Steel wire for lift ropes
1 Scope
This standard specifies the terms and definitions, technical requirements, test methods, inspection rules, packaging, storage, transport, marking, and quality certification of steel wires for lift ropes.
This standard is applicable to steel wires for lift ropes with a nominal wire diameter of 0.15mm to 3.50mm.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 228.1 Metallic materials - Tensile testing - Part 1: Method of test at room temperature
GB/T 238 Metallic materials - Wire - Reverse bend test
GB/T 239.1 Metallic materials - Wire - Part 1: Simple torsion test
GB/T 341 Steel wire - Classification and terminology
GB/T 1839 Test method for gravimetric determination of the mass per unit area of galvanized coatings on steel products
GB/T 2103-2008 General requirements for acceptance, packing, marking and quality certification of steel wire
GB/T 2976 Metallic materials - Wire - Wrapping test
GB/T 4354 Hot rolled quality carbon steel wire rods
YB/T 081 Rule for rounding off of numerical values and judgment of testing values for technical standards of metallurgy
3 Terms and definitions
For the purposes of this document, the terms and definitions given in GB/T 341 and the following apply.
3.1
nominal diameter
nominal diameter in millimeters, with which the inspection and acceptance of various technical indicators are carried out
3.2
actual diameter
arithmetic mean of two measurements taken in mutually perpendicular directions on the same cross-section of the steel wire
4 Technical requirements
4.1 Raw materials
The wire rods for steel wires shall comply with the provisions of GB/T 4354, and the grade shall be selected by the manufacturer; after mutual consultation between the supplier and the purchaser and as specified in the contract, wire rods of other steel classes and grades may also be selected.
4.2 Diameter and permissible deviation
The nominal diameter and permissible deviation of steel wire shall be as specified in Table 1.
Table 1 Permissible deviation of diameter
4.3 Out-of-roundness
The out-of-roundness of steel wire shall not be larger than half of the nominal diameter tolerance.
4.4 Shape
The steel wire can be delivered by coil or spool packaging method. The spool shall be wrapped tightly and flat, and the coil shall not be loose, and it shall not be in a "∞" shape when opened.
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Technical requirements
5 Test methods
6 Inspection rules
7 Packaging, storage and transport
8 Marking and quality certification
Steel wire for lift ropes
1 Scope
This standard specifies the terms and definitions, technical requirements, test methods, inspection rules, packaging, storage, transport, marking, and quality certification of steel wires for lift ropes.
This standard is applicable to steel wires for lift ropes with a nominal wire diameter of 0.15mm to 3.50mm.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 228.1 Metallic materials - Tensile testing - Part 1: Method of test at room temperature
GB/T 238 Metallic materials - Wire - Reverse bend test
GB/T 239.1 Metallic materials - Wire - Part 1: Simple torsion test
GB/T 341 Steel wire - Classification and terminology
GB/T 1839 Test method for gravimetric determination of the mass per unit area of galvanized coatings on steel products
GB/T 2103-2008 General requirements for acceptance, packing, marking and quality certification of steel wire
GB/T 2976 Metallic materials - Wire - Wrapping test
GB/T 4354 Hot rolled quality carbon steel wire rods
YB/T 081 Rule for rounding off of numerical values and judgment of testing values for technical standards of metallurgy
3 Terms and definitions
For the purposes of this document, the terms and definitions given in GB/T 341 and the following apply.
3.1
nominal diameter
nominal diameter in millimeters, with which the inspection and acceptance of various technical indicators are carried out
3.2
actual diameter
arithmetic mean of two measurements taken in mutually perpendicular directions on the same cross-section of the steel wire
4 Technical requirements
4.1 Raw materials
The wire rods for steel wires shall comply with the provisions of GB/T 4354, and the grade shall be selected by the manufacturer; after mutual consultation between the supplier and the purchaser and as specified in the contract, wire rods of other steel classes and grades may also be selected.
4.2 Diameter and permissible deviation
The nominal diameter and permissible deviation of steel wire shall be as specified in Table 1.
Table 1 Permissible deviation of diameter
4.3 Out-of-roundness
The out-of-roundness of steel wire shall not be larger than half of the nominal diameter tolerance.
4.4 Shape
The steel wire can be delivered by coil or spool packaging method. The spool shall be wrapped tightly and flat, and the coil shall not be loose, and it shall not be in a "∞" shape when opened.
Contents of YB/T 5198-2015
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Technical requirements
5 Test methods
6 Inspection rules
7 Packaging, storage and transport
8 Marking and quality certification
