Standard No.:	JB/T 9214-2010
English Name:	Non-destructive Testing - Test Methods for Evaluating Performance Characteristics of A-scan Pulse-echo Ultrasonic Testing Systems
Chinese Name:	无损检测 A型脉冲反射式超声检测系统工作性能测试方法
Professional Classification:	JB    Professional Standard - Machinery
Issued by:	MIIT
Issued on:	2010-2-11
Implemented on:	2010-7-1
Status:	valid
Superseding:	JB/T 9214-1999 Practice for evaluating performance characteristics of A scope ultrasonic pulse. Echo testing systems
Language:	English
File Format:	PDF
Word Count:	5000 words
Price(USD):	100.0
Delivery:	via email in 1 business day

1 Scope 1.1 This standard applies when evaluating performance characteristics of ultrasonic testing systems at test field. The ultrasonic testing systems refer to equipment used in the test, including A-scan pulse-echo ultrasonic tester, ultrasonic probe and high frequency cable connected therewith. In the test, only standard block specified in this standard is used instead of any electronic instruments. 1.2 This standard only specifies test method for evaluating performance characteristics of ultrasonic testing systems, but does not propose performance index or acceptance condition. Where necessary, the supplier and the purchaser may make an antecedent negotiation and specify the minimum performance index which the ultrasonic testing systems shall reach when the product is accepted. 1.3 This standard is only applicable to manual testing but not to automatic ultrasonic testing. 1.4 This standard is only applicable to the system including ordinary contact ultrasonic normal probe or angled probe but not to the systems including ultrasonic probes of other types (such as bicrystal type and water immersion type). 2 Normative References The following documents contain provisions which, through reference in this standard, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections) to, or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of these documents is applicable. For undated references, the latest edition of the normative documents applies. GB/T 12604.1 Non-destructive Testing—Terminology—Terms Used in Ultrasonic Testing (GB/T 12604.1-2005, ISO 5577: 2000, DT) GB/T 19799.1-2005 Non-destructive Testing—Ultrasonic Testing—Calibration Block No.1 (ISO 2400: 1972, DT) GB/T 20737 Non-destructive Testing—General Terms and Definitions (GB/T 20737-2006, ISO/TS 18173: 2005, IDT) JB/T 8428-2006 Non-destructive Testing—Blocks for Ultrasonic Testing 3 Terms and Definitions For the purpose of this standard, the terms and definitions given in GB/T 12604.1 and GB/T 20737 apply.

Foreword i 1 Scope 2 Normative References 3 Terms and Definitions 4 Items under Test 5 Test Methods for Surplus Sensitivity of Normal Probe 6 Test Methods for Vertical Linearity of Normal Probe 7 Test Methods for Horizontal Linearity 8 Test Methods for Resolution of Normal Probe 9 Test Method for Dead Zone of Normal Probe 10 Test Methods for Point of Incidence of Angled Probe 11 Test Methods for Angle of Refraction or K Value of Angled Probe 12 Test Methods for Resolution of Angled Probe 13 Test Methods for Surplus Sensitivity of Angled Probe 14 Test Report Annex A (Normative) Standard Block Figure 1 Bottom Echo Indication in Horizontal Linearity Test Figure 2 Resolution Test for Normal Probe and Echo Indication Figure 3 Test of Point of Incidence of Angled Probe Figure 4 Test of Angle of Refraction or K Value of Angled Probe Figure 5 Echo Indication in Test of Angled probe Resolution Figure A.1 DB-P Block Figure A.2 DZ-I Block Table 1 Vertical Linearity Test Record Table A.1 DB-P Block Dimension