This standard specifies classification, code, designation, general requirements, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of washbasin faucet.
This standard is applicable to the washbasin faucets that are mounted on the cold and hot water supply pipes inside buildings under the conditions with the nominal pressure no larger than 1.0 MPa and the medium temperature no larger than 90 ℃.
2 Normative References
The following normative document contains provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 2828.1 Sampling Procedures for Inspection by Attributes — Part 1: Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-lot Inspection
GB/T 2829 Sampling Procedures and Tables for Periodic Inspection by Attributes (Apply to Inspection of Process Stability)
GB/T 6461 Methods for Corrosion Testing of Metallic and Other Inorganic Coatings on Metallic Substrates — Rating of Test Specimens and Manufactured Articles Subjected to Corrosion Tests
GB/T 7306.1 Pipe Threads with 55 Degree Thread Angle Where Pressure-tight Joints Are Made on the Threads — Part 1: Parallel Internal and Taper External Threads (eqv ISO 7-1:1994)
GB/T 7306.2 Pipe Threads with 55 Degree Thread Angle Where Pressure-tight Joints Are Made on the Threads — Part 2: Taper Internal and External Threads (eqv ISO 7-1:1994)
Foreword I 1 Scope 2 Normative References 3 Classification, Code and Designation 4 General Requirements 5 Technical Requirements 6 Test Methods 7 Inspection Rules 8 Marking, Packaging, Transportation and Storage
1 Scope
This standard specifies classification, code, designation, general requirements, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of washbasin faucet.
This standard is applicable to the washbasin faucets that are mounted on the cold and hot water supply pipes inside buildings under the conditions with the nominal pressure no larger than 1.0 MPa and the medium temperature no larger than 90 ℃.
2 Normative References
The following normative document contains provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 2828.1 Sampling Procedures for Inspection by Attributes — Part 1: Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-lot Inspection
GB/T 2829 Sampling Procedures and Tables for Periodic Inspection by Attributes (Apply to Inspection of Process Stability)
GB/T 6461 Methods for Corrosion Testing of Metallic and Other Inorganic Coatings on Metallic Substrates — Rating of Test Specimens and Manufactured Articles Subjected to Corrosion Tests
GB/T 7306.1 Pipe Threads with 55 Degree Thread Angle Where Pressure-tight Joints Are Made on the Threads — Part 1: Parallel Internal and Taper External Threads (eqv ISO 7-1:1994)
GB/T 7306.2 Pipe Threads with 55 Degree Thread Angle Where Pressure-tight Joints Are Made on the Threads — Part 2: Taper Internal and External Threads (eqv ISO 7-1:1994)
Contents of JC/T 758-2008
Foreword I
1 Scope
2 Normative References
3 Classification, Code and Designation
4 General Requirements
5 Technical Requirements
6 Test Methods
7 Inspection Rules
8 Marking, Packaging, Transportation and Storage
