1 Scope
This standard specifies terms and definitions, classification, materials, requirements, test methods, inspection rules, packaging, marking, transport and storage of laminated solar PV glazing materials in building.
This standard is applicable to crystalline silicon cell type and thin-film cell type laminated solar PV glazing materials in buildings.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 308 Rolling bearings - Steel balls
GB/T 531.1 Rubber vulcanized or thermoplastic - Determination of indentation hardness - Part 1: Duromerer method (Shore hardness)
GB/T 1216 External micrometer
GB/T 5137.3-2002 Test methods of safety glazing materials used on road vehicles - Part 3: Radiation, high temperature, humidity, fire and simulated weathering resistance tests
GB/T 9056 Metal ruler
GB 11614 Flat glass
GB 15763.1 Safety glazing materials in building - Part 1: Fire-resistant glass
GB 15763.2 Safety glazing materials in building - Part 2: Tempered glass
GB 15763.4 Safety glazing materials in building - Part 4: Heat soaked thermally tempered glass
GB/T 17841 Heat strengthened glass
GB/T 21389 Vernier, dial and digital display calipers
JC/T 677 Test method to model wind pressure for architectural glass under the uniform static loads
JC/T 1006 Enamelled tempered and heat-strengthened glass
IEC 61215: 2005 Crystalline silicon terrestrial photovoltaic (PV) modules - Design qualification and type approval
IEC 61646: 2008 Thin-film terrestrial photovoltaic (PV) modules - Design qualification and type approval
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
laminated solar PV glazing materials
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Materials
6 Requirements
7 Test methods
8 Inspection rules
9 Packaging, marking, transport and storage
Annex A (Normative) Holder for falling ball impact test
Annex B (Normative ) Test device for shot-bag impact performance
Annex C (Normative) Forcemeter
Annex D (Informative) Calibration of shot-bag impact rating test frames
1 Scope
This standard specifies terms and definitions, classification, materials, requirements, test methods, inspection rules, packaging, marking, transport and storage of laminated solar PV glazing materials in building.
This standard is applicable to crystalline silicon cell type and thin-film cell type laminated solar PV glazing materials in buildings.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 308 Rolling bearings - Steel balls
GB/T 531.1 Rubber vulcanized or thermoplastic - Determination of indentation hardness - Part 1: Duromerer method (Shore hardness)
GB/T 1216 External micrometer
GB/T 5137.3-2002 Test methods of safety glazing materials used on road vehicles - Part 3: Radiation, high temperature, humidity, fire and simulated weathering resistance tests
GB/T 9056 Metal ruler
GB 11614 Flat glass
GB 15763.1 Safety glazing materials in building - Part 1: Fire-resistant glass
GB 15763.2 Safety glazing materials in building - Part 2: Tempered glass
GB 15763.4 Safety glazing materials in building - Part 4: Heat soaked thermally tempered glass
GB/T 17841 Heat strengthened glass
GB/T 21389 Vernier, dial and digital display calipers
JC/T 677 Test method to model wind pressure for architectural glass under the uniform static loads
JC/T 1006 Enamelled tempered and heat-strengthened glass
IEC 61215: 2005 Crystalline silicon terrestrial photovoltaic (PV) modules - Design qualification and type approval
IEC 61646: 2008 Thin-film terrestrial photovoltaic (PV) modules - Design qualification and type approval
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
laminated solar PV glazing materials
Contents of GB 29551-2013
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Materials
6 Requirements
7 Test methods
8 Inspection rules
9 Packaging, marking, transport and storage
Annex A (Normative) Holder for falling ball impact test
Annex B (Normative ) Test device for shot-bag impact performance
Annex C (Normative) Forcemeter
Annex D (Informative) Calibration of shot-bag impact rating test frames