This standard specifies the technical conditions and technical requirements for amusement rides shooting category.
This standard is applicable to the design, manufacturing, installation, reconstruction, maintenance, test, inspection and application management of amusement rides shooting category (hereinafter referred to as amusement rides shooting).
2 Normative References
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments to (excluding amending errors in the text), or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of the normative document is applicable. For undated references, the latest edition of the normative document applies.
GB/T 2828.1 Sampling Procedures for Inspection by Attribute - Part 1: Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-lot Inspection (GB/T 2828.1-2003, ISO 2859-1:1999, IDT)
GB 8408-2008 Amusement Device Safety Code
JB/T 5000.12-1998 The Heavy Mechanical General Techniques and Standards Coating
3 General Requirements
3.1 Amusement rides shooting refers to amusement rides with signal, audio equipment, lamplight and digital display and mutually coordinated with mechanical action, target and shooting as well as those of similar type.
3.2 The design, manufacturing, installation, reconstruction, maintenance, test, inspection and application management of amusement rides shooting shall be implemented according to the relevant requirements of GB 8408-2008 and this standard.
3.3 Personnel safety shall be ensured during the design, manufacturing, installation and application of amusement rides shooting.
3.4 Other requirements not mentioned in this standard shall be implemented according to relevant national standards, regulations and requirements.
Foreword I 1 Scope 2 Normative References 3 General Requirements 4 Basic Design Requirements 5 Drive System 6 Electrical and Control Systems 7 Manufacturing and Installation 8 Test Method 9 Inspection Rules
1 Scope
This standard specifies the technical conditions and technical requirements for amusement rides shooting category.
This standard is applicable to the design, manufacturing, installation, reconstruction, maintenance, test, inspection and application management of amusement rides shooting category (hereinafter referred to as amusement rides shooting).
2 Normative References
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments to (excluding amending errors in the text), or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of the normative document is applicable. For undated references, the latest edition of the normative document applies.
GB/T 2828.1 Sampling Procedures for Inspection by Attribute - Part 1: Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-lot Inspection (GB/T 2828.1-2003, ISO 2859-1:1999, IDT)
GB 8408-2008 Amusement Device Safety Code
JB/T 5000.12-1998 The Heavy Mechanical General Techniques and Standards Coating
3 General Requirements
3.1 Amusement rides shooting refers to amusement rides with signal, audio equipment, lamplight and digital display and mutually coordinated with mechanical action, target and shooting as well as those of similar type.
3.2 The design, manufacturing, installation, reconstruction, maintenance, test, inspection and application management of amusement rides shooting shall be implemented according to the relevant requirements of GB 8408-2008 and this standard.
3.3 Personnel safety shall be ensured during the design, manufacturing, installation and application of amusement rides shooting.
3.4 Other requirements not mentioned in this standard shall be implemented according to relevant national standards, regulations and requirements.
Contents of GB/T 18167-2008
Foreword I
1 Scope
2 Normative References
3 General Requirements
4 Basic Design Requirements
5 Drive System
6 Electrical and Control Systems
7 Manufacturing and Installation
8 Test Method
9 Inspection Rules
