2023-9-22 3.239.59.31
Code of China Chinese Classification Professional Classification ICS Classification Latest News Value-added Services

Position: Chinese Standard in English/GB/T 3478.1-2008
GB/T 3478.1-2008   Straight cylindrical involute splines - Metric module side fit - Part 1: Generalities (English Version)
Standard No.: GB/T 3478.1-2008 Status:valid remind me the status change

Email:

Language:English File Format:PDF
Word Count: 39000 words Price(USD):140.0 remind me the price change

Email:

Implemented on:2009-5-1 Delivery: via email in 1 business day
,,
Standard No.: GB/T 3478.1-2008
English Name: Straight cylindrical involute splines - Metric module side fit - Part 1: Generalities
Chinese Name: 圆柱直齿渐开线花键(米制模数 齿侧配合) 第1部分:总论
Chinese Classification: J18    Chain drive, belt drive and key joint
Professional Classification: GB    National Standard
ICS Classification: 21.120.30 21.120.30    Keys and keyways, splines 21.120.30
Issued by: AQSIQ, SAC
Issued on: 2008-09-22
Implemented on: 2009-5-1
Status: valid
Superseding:GB/T 3478.1-1995 Straight cylindrical involute splines-Modules, basic rack profiles and tolerances
Language: English
File Format: PDF
Word Count: 39000 words
Price(USD): 140.0
Delivery: via email in 1 business day
1 Scope This part of GB/T 3478 specifies the series of modules, basic tooth profiles, tolerances and side-fit classification for straight cylindrical involute splines. This part is applicable to side-fitting straight cylindrical involute splines of standard pressure angles of 30° and 37.5 ° (modules from 0.5 mm ~ 10 mm), 45° (modules from 0.25 mm ~ 2.5 mm). Note: for computer management, 37°30″ is expressed as 37.5°. 2 Normative References The following documents contain provisions which, through reference in this part of GB/T 3478, constitute provisions of this Part. For dated reference, subsequent amendments to (excluding any corrigendum), or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For any undated references, the latest edition of the document referred to applies. GB/T 1800.1 Geometrical Product Specifications (GPS) - Limits and Fits - Part 1: Bases of Tolerances, Deviations and Fits GB/T 3478.5 Straight Cylindrical Involute Spline - Metric Module, Side Fit - Part 5: Inspection (GB/T 3478.5-2008, ISO 4156-3:2005, (Straight Cylindrical Involute Splines-Metric Module, Side Fit-Part 3: Inspection), MOD) 3 Terms and Definitions See Table 1 and Figure 1 for the terms and definitions applied in this part (30° pressure angle flat root, hereinafter referred to as "30° flat root "; 30° pressure angle fillet root as 30° fillet root; 37.5 ° pressure angle fillet root as 37.5 ° fillet root; 45° pressure angle fillet root as 45°fillet root). For the purpose of this part, the following terms and definitions apply. Table 1 Terms, Symbols and Definitions ... ... ... .. 4 Basic Parameters 4.1 See Table 2 for basic parameters. 4.2 The standard pressure angle αD is the tooth profile angle of basic tooth form. 4.3 Module m is classified into two series, 15 types; series 1 is preferred.
Foreword i 1 Scope 2 Normative References 3 Terms and Definitions 4 Basic Parameters 5 Basic Tooth Profiles 6 Dimension Series 7 Tolerance Classes 8 Tolerances 9 Side Fit 10 Effective Dimensions and Actual Dimensions 11 Inspection Methods 12 Parameter Annotation 13 Calculation Examples Appendix A (Normative) Conditions and Requirements for Application of Straight Tooth Form for Internal Spline Appendix B (Informative) Radial Runout Tolerance of Tooth Ring Appendix C (Informative) Calculation Examples of Spline
Referred in GB/T 3478.1-2008:
*GB/T 1800.1-2009 Geometrical product specifications (GPS) - Limits and fits - Part 1: Bases of tolerances deviations and fits
*GB/T 3478.5-2008 Straight cylindrical involute splines - Metric module side fit - Part 5: Inspection
GB/T 3478.1-2008 is referred in:
*GB/T 5104-2008 The basic types and dimensions of hobs for involute splines
*GB/T 17855-2017 Calculation of load capacity of spline
Code of China
Standard
GB/T 3478.1-2008  Straight cylindrical involute splines - Metric module side fit - Part 1: Generalities (English Version)
Standard No.GB/T 3478.1-2008
Statusvalid
LanguageEnglish
File FormatPDF
Word Count39000 words
Price(USD)140.0
Implemented on2009-5-1
Deliveryvia email in 1 business day
Detail of GB/T 3478.1-2008
Standard No.
GB/T 3478.1-2008
English Name
Straight cylindrical involute splines - Metric module side fit - Part 1: Generalities
Chinese Name
圆柱直齿渐开线花键(米制模数 齿侧配合) 第1部分:总论
Chinese Classification
J18
Professional Classification
GB
ICS Classification
Issued by
AQSIQ, SAC
Issued on
2008-09-22
Implemented on
2009-5-1
Status
valid
Superseded by
Superseded on
Abolished on
Superseding
GB/T 3478.1-1995 Straight cylindrical involute splines-Modules, basic rack profiles and tolerances
Language
English
File Format
PDF
Word Count
39000 words
Price(USD)
140.0
Keywords
GB/T 3478.1-2008, GB 3478.1-2008, GBT 3478.1-2008, GB/T3478.1-2008, GB/T 3478.1, GB/T3478.1, GB3478.1-2008, GB 3478.1, GB3478.1, GBT3478.1-2008, GBT 3478.1, GBT3478.1
Introduction of GB/T 3478.1-2008
1 Scope This part of GB/T 3478 specifies the series of modules, basic tooth profiles, tolerances and side-fit classification for straight cylindrical involute splines. This part is applicable to side-fitting straight cylindrical involute splines of standard pressure angles of 30° and 37.5 ° (modules from 0.5 mm ~ 10 mm), 45° (modules from 0.25 mm ~ 2.5 mm). Note: for computer management, 37°30″ is expressed as 37.5°. 2 Normative References The following documents contain provisions which, through reference in this part of GB/T 3478, constitute provisions of this Part. For dated reference, subsequent amendments to (excluding any corrigendum), or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For any undated references, the latest edition of the document referred to applies. GB/T 1800.1 Geometrical Product Specifications (GPS) - Limits and Fits - Part 1: Bases of Tolerances, Deviations and Fits GB/T 3478.5 Straight Cylindrical Involute Spline - Metric Module, Side Fit - Part 5: Inspection (GB/T 3478.5-2008, ISO 4156-3:2005, (Straight Cylindrical Involute Splines-Metric Module, Side Fit-Part 3: Inspection), MOD) 3 Terms and Definitions See Table 1 and Figure 1 for the terms and definitions applied in this part (30° pressure angle flat root, hereinafter referred to as "30° flat root "; 30° pressure angle fillet root as 30° fillet root; 37.5 ° pressure angle fillet root as 37.5 ° fillet root; 45° pressure angle fillet root as 45°fillet root). For the purpose of this part, the following terms and definitions apply. Table 1 Terms, Symbols and Definitions ... ... ... .. 4 Basic Parameters 4.1 See Table 2 for basic parameters. 4.2 The standard pressure angle αD is the tooth profile angle of basic tooth form. 4.3 Module m is classified into two series, 15 types; series 1 is preferred.
Contents of GB/T 3478.1-2008
Foreword i 1 Scope 2 Normative References 3 Terms and Definitions 4 Basic Parameters 5 Basic Tooth Profiles 6 Dimension Series 7 Tolerance Classes 8 Tolerances 9 Side Fit 10 Effective Dimensions and Actual Dimensions 11 Inspection Methods 12 Parameter Annotation 13 Calculation Examples Appendix A (Normative) Conditions and Requirements for Application of Straight Tooth Form for Internal Spline Appendix B (Informative) Radial Runout Tolerance of Tooth Ring Appendix C (Informative) Calculation Examples of Spline
About Us   |    Contact Us   |    Terms of Service   |    Privacy   |    Cancellation & Refund Policy   |    Payment
Tel: +86-10-8572 5655 | Fax: +86-10-8581 9515 | Email: coc@codeofchina.com | QQ: 672269886
Copyright: TransForyou Co., Ltd. 2008-2040
 
 
Keywords:
GB/T 3478.1-2008, GB 3478.1-2008, GBT 3478.1-2008, GB/T3478.1-2008, GB/T 3478.1, GB/T3478.1, GB3478.1-2008, GB 3478.1, GB3478.1, GBT3478.1-2008, GBT 3478.1, GBT3478.1