Industrial woven metal wire cloth (square opening series)
1 Scope
This standard specifies the weaving type, model, specification, designation, technical requirements, test methods, inspection rules and marking of industrial woven metal wire cloth for screening and filtration.
This standard is applicable to the industrial woven metal wire cloth (square opening series) for screening of solid particles, filtration of liquid and gas substances and other industrial uses.
This standard is applicable to the industrial woven metal wire cloth (square opening series) with a nominal opening size of 0.02mm to 16.0mm.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections) to, or revisions of, any of these publications do not apply to this standard. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 699 Quality carbon structure steels
GB/T 4239 Cold rolled stainless steel and heat-resisting steel strips
GB/T 5231 Wrought copper and copper alloys chemical composition limits and forms of wrought products
GB/T 10611 Industrial screens - Designation and nominal sizes of apertures (GB/T 10611-2003, ISO 2194:1991 Industrial screens - Woven wire cloth, perforated plate and electroformed sheet - Designation and nominal sizes of openings, MOD)
3 Weaving type, model and specification
3.1 Weaving type
The weaving type of industrial woven metal wire cloth (square opening series) is classified into plain weaving (see Figure 1) and twill weaving (see Figure 2).
Foreword i
1 Scope
2 Normative references
3 Weaving type, model and specification
4 Technical requirements
5 Test method
6 Inspection rules
7 Marking, packaging, transportation and storage
Annex A (Informative) Structural parameters and mesh number of industrial woven metal wire cloth (square opening series)
Annex B (Informative) Structural parameters and mesh number of industrial woven metal wire cloth (square opening series) (supplementary sizes)
Annex C (Informative) Terms and definitions of cloth surface defects and weaving defects of woven metal wire cloth
Industrial woven metal wire cloth (square opening series)
1 Scope
This standard specifies the weaving type, model, specification, designation, technical requirements, test methods, inspection rules and marking of industrial woven metal wire cloth for screening and filtration.
This standard is applicable to the industrial woven metal wire cloth (square opening series) for screening of solid particles, filtration of liquid and gas substances and other industrial uses.
This standard is applicable to the industrial woven metal wire cloth (square opening series) with a nominal opening size of 0.02mm to 16.0mm.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections) to, or revisions of, any of these publications do not apply to this standard. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 699 Quality carbon structure steels
GB/T 4239 Cold rolled stainless steel and heat-resisting steel strips
GB/T 5231 Wrought copper and copper alloys chemical composition limits and forms of wrought products
GB/T 10611 Industrial screens - Designation and nominal sizes of apertures (GB/T 10611-2003, ISO 2194:1991 Industrial screens - Woven wire cloth, perforated plate and electroformed sheet - Designation and nominal sizes of openings, MOD)
3 Weaving type, model and specification
3.1 Weaving type
The weaving type of industrial woven metal wire cloth (square opening series) is classified into plain weaving (see Figure 1) and twill weaving (see Figure 2).
Contents of GB/T 5330-2003
Foreword i
1 Scope
2 Normative references
3 Weaving type, model and specification
4 Technical requirements
5 Test method
6 Inspection rules
7 Marking, packaging, transportation and storage
Annex A (Informative) Structural parameters and mesh number of industrial woven metal wire cloth (square opening series)
Annex B (Informative) Structural parameters and mesh number of industrial woven metal wire cloth (square opening series) (supplementary sizes)
Annex C (Informative) Terms and definitions of cloth surface defects and weaving defects of woven metal wire cloth