GB/T 8626-2026 Test method of flammability for building materials
Warning:
Fire testing can be hazardous and that there is a possibility that toxic and/ or harmful smoke and gases can be evolved during the test. Operational hazards can also arise during the testing of specimens and the disposal of test residues.
An assessment of all potential hazards and risks to health shall be made and safety precautions identified and provided. Written safety instructions shall be issued. Appropriate training shall be given to relevant personnel. Laboratory personnel shall ensure that they follow written safety instructions at all times.
It’s critical to provide adequate means of extinguishing.
In some cases, smouldering can be difficult to extinguish completely and immersion in water may be necessary.
1 Scope
This document specifies a method of test for determining the ignitability of products by direct small flame impingement under zero impressed irradiance using vertically oriented test specimens.
This document applies to the determination of flammability for building materials, decorative and finishing materials and products used in industrial and civil buildings. The determination of flammability for materials and products used in other places may refer to this document.
Information on the precision of the test method is given in Annex A. Information on testing not essentially flat end-use products is given in Annex B. Information on testing perforated end-use products is given in Annex C.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendments) applies.
GB/T 5907.1 Fire protection vocabulary - Part 1: General terms
GB/T 5907.2 Fire protection vocabulary - Part 2: Fire prevention
GB 8624 Classification for burning behavior of building materials and products
GB/T 40238 Reaction to fire tests for building materials and products - General rules for selection of substrates, conditioning and mounting of specimen
3 Terms and definitions
For the purpose of this document, the terms and definitions given in GB/T 5907.1, GB/T 5907.2 and GB 8624 and the following apply.
3.1
product
material, element or component about which information is required
3.2
essentially flat product
product having one of the following characteristics:
a) a planar exposed surface;
b) a planar exposed surface with a surface irregularity that is evenly distributed over the exposed surface, provided that
1) at least 50 % of the surface of a representative square area of 250 mm × 250 mm lies within a depth of 6 mm from a plane taken across the highest points on the exposed surface, or
2) for a surface containing cracks, fissures or holes, these do not exceed 6.5 mm in width or 10 mm in depth, and that the total area of such cracks, fissures or holes at the surface does not exceed 30 % of a representative square area of 250 mm × 250 mm of the exposed surface
3.3
flaming droplet/particle
material separating from the specimen during the fire test procedure and igniting the filter paper beneath the specimen
3.4
multi-layered product
product composed of two or more layers of different materials
Note: multi-layered product can be either substantial and/or non-substantial
3.5
sustained flaming
persistence of flame for a period greater than 3s
3.6
ignition
presence of sustained flaming
4 Test apparatus
4.1 Test laboratory
Test laboratory, capable of providing an environment at (23 ± 5) °C and a relative humidity of (50 ± 20) %.
Note: It has been found that a partially darkened room assists with the perception of small surface flames.
4.2 Combustion chamber
Combustion chamber, consisting of an enclosure constructed from stainless steel sheets, with heat-resistant, glazed doors provided for access and observation in at least the front and one lateral side, see Figures 1a) and 1b). Ventilation of the enclosure shall be free through the square box section base in the bottom of the chamber, see Figures 1c). This shall be made of stainless steel of 1.5 mm thickness, 50 mm in height, with the open square area being 25 mm × 25 mm, see Figures 1d). To make free ventilation possible, the chamber shall stand on 40 mm high supports which provide a gap at the bottom of the combustion chamber. The combustion chamber shall be situated under a suitably ventilated hood. The air velocity measured on the central axis in the chimney of the combustion chamber shall be (0.7 ± 0.1) m/s, measured with the burner only ignited and with the ventilation hood “on”.
Dimensions in millimeters
a) Front view b) Right side view
c) Square box section base in the bottom of the chamber d) Open square
Key
1 - measuring point for air velocity
2 - metal grid mesh
3 - horizontal plate
4 - chimney
Note: All dimensions are nominal values in millimetres unless tolerances are given.
Figure 1 Combustion box
4.3 Burner
The burner, as shown in Figure 2a), consists of a gas jet, burner tube and flame stabilizer, see Figure 2b) to Figure 2d). It shall be such designed that it can be used vertically or be tilted at 45° with respect to the vertical axis. The burner shall be mounted onto a horizontal plate so that it moves smoothly forwards and backwards along the centreline of the combustion chamber.
Contents
Foreword Ⅲ
1 Scope
2 Normative references
3 Terms and definitions
4 Test apparatus
5 Test specimen
6 Conditioning
7 Test procedure
8 Expression of results
9 Test report
Annex A (Informative) Precision of test method
Annex B (Normative) Testing information of not essentially flat end-use products
Annex C (Normative) Testing information of perforated end-use products
Bibliography
GB/T 8626-2026 Test method of flammability for building materials
Warning:
Fire testing can be hazardous and that there is a possibility that toxic and/ or harmful smoke and gases can be evolved during the test. Operational hazards can also arise during the testing of specimens and the disposal of test residues.
An assessment of all potential hazards and risks to health shall be made and safety precautions identified and provided. Written safety instructions shall be issued. Appropriate training shall be given to relevant personnel. Laboratory personnel shall ensure that they follow written safety instructions at all times.
It’s critical to provide adequate means of extinguishing.
In some cases, smouldering can be difficult to extinguish completely and immersion in water may be necessary.
1 Scope
This document specifies a method of test for determining the ignitability of products by direct small flame impingement under zero impressed irradiance using vertically oriented test specimens.
This document applies to the determination of flammability for building materials, decorative and finishing materials and products used in industrial and civil buildings. The determination of flammability for materials and products used in other places may refer to this document.
Information on the precision of the test method is given in Annex A. Information on testing not essentially flat end-use products is given in Annex B. Information on testing perforated end-use products is given in Annex C.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendments) applies.
GB/T 5907.1 Fire protection vocabulary - Part 1: General terms
GB/T 5907.2 Fire protection vocabulary - Part 2: Fire prevention
GB 8624 Classification for burning behavior of building materials and products
GB/T 40238 Reaction to fire tests for building materials and products - General rules for selection of substrates, conditioning and mounting of specimen
3 Terms and definitions
For the purpose of this document, the terms and definitions given in GB/T 5907.1, GB/T 5907.2 and GB 8624 and the following apply.
3.1
product
material, element or component about which information is required
3.2
essentially flat product
product having one of the following characteristics:
a) a planar exposed surface;
b) a planar exposed surface with a surface irregularity that is evenly distributed over the exposed surface, provided that
1) at least 50 % of the surface of a representative square area of 250 mm × 250 mm lies within a depth of 6 mm from a plane taken across the highest points on the exposed surface, or
2) for a surface containing cracks, fissures or holes, these do not exceed 6.5 mm in width or 10 mm in depth, and that the total area of such cracks, fissures or holes at the surface does not exceed 30 % of a representative square area of 250 mm × 250 mm of the exposed surface
3.3
flaming droplet/particle
material separating from the specimen during the fire test procedure and igniting the filter paper beneath the specimen
3.4
multi-layered product
product composed of two or more layers of different materials
Note: multi-layered product can be either substantial and/or non-substantial
3.5
sustained flaming
persistence of flame for a period greater than 3s
3.6
ignition
presence of sustained flaming
4 Test apparatus
4.1 Test laboratory
Test laboratory, capable of providing an environment at (23 ± 5) °C and a relative humidity of (50 ± 20) %.
Note: It has been found that a partially darkened room assists with the perception of small surface flames.
4.2 Combustion chamber
Combustion chamber, consisting of an enclosure constructed from stainless steel sheets, with heat-resistant, glazed doors provided for access and observation in at least the front and one lateral side, see Figures 1a) and 1b). Ventilation of the enclosure shall be free through the square box section base in the bottom of the chamber, see Figures 1c). This shall be made of stainless steel of 1.5 mm thickness, 50 mm in height, with the open square area being 25 mm × 25 mm, see Figures 1d). To make free ventilation possible, the chamber shall stand on 40 mm high supports which provide a gap at the bottom of the combustion chamber. The combustion chamber shall be situated under a suitably ventilated hood. The air velocity measured on the central axis in the chimney of the combustion chamber shall be (0.7 ± 0.1) m/s, measured with the burner only ignited and with the ventilation hood “on”.
Dimensions in millimeters
a) Front view b) Right side view
c) Square box section base in the bottom of the chamber d) Open square
Key
1 - measuring point for air velocity
2 - metal grid mesh
3 - horizontal plate
4 - chimney
Note: All dimensions are nominal values in millimetres unless tolerances are given.
Figure 1 Combustion box
4.3 Burner
The burner, as shown in Figure 2a), consists of a gas jet, burner tube and flame stabilizer, see Figure 2b) to Figure 2d). It shall be such designed that it can be used vertically or be tilted at 45° with respect to the vertical axis. The burner shall be mounted onto a horizontal plate so that it moves smoothly forwards and backwards along the centreline of the combustion chamber.
Contents of GB/T 8626-2026
Contents
Foreword Ⅲ
1 Scope
2 Normative references
3 Terms and definitions
4 Test apparatus
5 Test specimen
6 Conditioning
7 Test procedure
8 Expression of results
9 Test report
Annex A (Informative) Precision of test method
Annex B (Normative) Testing information of not essentially flat end-use products
Annex C (Normative) Testing information of perforated end-use products
Bibliography