General specification for onboard cable network of missile/launch vehicle
1 Scope
This specification specifies the requirements, quality assurance requirements and delivery preparation of onboard cable network of missile/launch vehicle.
It is applicable to the design, production, test and acceptance of onboard cable network of missile/launch vehicle.
2 Normative references
The following documents contain provisions which, through reference in this text, constitute provisions of this specification. For dated reference, subsequent amendments to (excluding any corrigendum), or revisions of, any of these publications do not apply. However, parties to agreements based on this specification are encouraged to investigate the possibility of applying the most recent editions of the documents indicated below. For undated references, the latest edition of the normative document referred to applies.
QJ 19 Specification for preparation of product certificates
QJ 165 General specifications for installation of aerospace electronic and electrical products
QJ 603 General technical requirements for electric cable assemble manufacturing
QJ 1238.2 Test method for onboard cable of missile/launch vehicle - Part 2: Low temperature test
QJ 1238.3 Test method for onboard cable of missile/launch vehicle - Part 3: High temperature test
QJ 1238.4 Test method for onboard cable of missile/launch vehicle - Part 4: Cyclic damp heat test
QJ 1238.6 Test method for onboard cable of missile/launch vehicle - Part 6: Mold test
QJ 1238.7 Test method for onboard cable of missile/launch vehicle - Part 7: Salt spray test
QJ 1238.9 Test method for onboard cable of missile/launch vehicle - Part 9: Impulse test
QJ 1238.10 Test method for onboard cable of missile/launch vehicle - Part 10: Vibration test
QJ 1238.11 Test method for onboard cable of missile/launch vehicle - Part 11: Acceleration test
QJ 1238.15 Test method for onboard cable of missile/launch vehicle - Part 15: Line correctness test
QJ 1238.16 Test method for onboard cable of missile/launch vehicle - Part 16: Insulation resistance test
QJ 1238.17 Test method for onboard cable of missile/launch vehicle - Part 17: AC voltage test
QJ 1238.18 Test method for onboard cable of missile/launch vehicle - Part 18: Low air pressure test
QJ 1238.19 Test method for onboard cable of missile/launch vehicle - Part 19: Road transportation simulation test method
QJ 2847 Specification for wooden packing boxes for electronic products
QJ 2850 Prevention and control for foreign object debris (FOD) of space products
QJ 2999 Specification for preparation of product quality logbook
3 Requirements
3.1 General
General specification for onboard cable network of missile/launch vehicle
1 Scope
This specification specifies the requirements, quality assurance requirements and delivery preparation of onboard cable network of missile/launch vehicle.
It is applicable to the design, production, test and acceptance of onboard cable network of missile/launch vehicle.
2 Normative references
The following documents contain provisions which, through reference in this text, constitute provisions of this specification. For dated reference, subsequent amendments to (excluding any corrigendum), or revisions of, any of these publications do not apply. However, parties to agreements based on this specification are encouraged to investigate the possibility of applying the most recent editions of the documents indicated below. For undated references, the latest edition of the normative document referred to applies.
QJ 19 Specification for preparation of product certificates
QJ 165 General specifications for installation of aerospace electronic and electrical products
QJ 603 General technical requirements for electric cable assemble manufacturing
QJ 1238.2 Test method for onboard cable of missile/launch vehicle - Part 2: Low temperature test
QJ 1238.3 Test method for onboard cable of missile/launch vehicle - Part 3: High temperature test
QJ 1238.4 Test method for onboard cable of missile/launch vehicle - Part 4: Cyclic damp heat test
QJ 1238.6 Test method for onboard cable of missile/launch vehicle - Part 6: Mold test
QJ 1238.7 Test method for onboard cable of missile/launch vehicle - Part 7: Salt spray test
QJ 1238.9 Test method for onboard cable of missile/launch vehicle - Part 9: Impulse test
QJ 1238.10 Test method for onboard cable of missile/launch vehicle - Part 10: Vibration test
QJ 1238.11 Test method for onboard cable of missile/launch vehicle - Part 11: Acceleration test
QJ 1238.15 Test method for onboard cable of missile/launch vehicle - Part 15: Line correctness test
QJ 1238.16 Test method for onboard cable of missile/launch vehicle - Part 16: Insulation resistance test
QJ 1238.17 Test method for onboard cable of missile/launch vehicle - Part 17: AC voltage test
QJ 1238.18 Test method for onboard cable of missile/launch vehicle - Part 18: Low air pressure test
QJ 1238.19 Test method for onboard cable of missile/launch vehicle - Part 19: Road transportation simulation test method
QJ 2847 Specification for wooden packing boxes for electronic products
QJ 2850 Prevention and control for foreign object debris (FOD) of space products
QJ 2999 Specification for preparation of product quality logbook
3 Requirements
3.1 General