1 Scope
This specification specifies the requirements, quality assurance requirements and delivery preparation of the missile hooking vehicle of tactical missile (hereinafter referred to as “vehicle”).
This specification is applicable to the design, manufacture and acceptance of missile hooking vehicle of tactical missile, and the hooking equipment of other types of airborne weapons may also be implemented with reference.
2 Normative references
The following documents contain provisions which, through reference in this text, constitute provisions of this code. For dated reference, subsequent amendments to (excluding any corrigendum), or revisions of, any of these publications do not apply. However, parties to agreements based on this specification are encouraged to investigate the possibility of applying the most recent editions of the documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 191 Packaging—Pictorial marking for handling of goods
GB/T 3766-2001 Hydraulic fluid power—General rules relating to systems
GB 11118.1 Mineral oil type and synthetic hydrocarbon type hydraulic oil
GB/T 14039-2002 Hydraulic fluid power—Fluids—Method for coding the level of contamination by solid particles
GJB 4.11-1983 Environmental test of ship electronic equipment—Salt spray test
GJB 145A-1993 Specification of preservation packaging
GJB 150.3-1986 Environmental test methods for military equipments—High temperature test
GJB 150.4-1986 Environmental test methods for military equipments—Low temperature test
GJB 150.10-1986 Environmental test methods for military equipments—Fungus test
GJB 150.11-1986 Environmental test methods for military equipments—Salt fog test
GJB 368A-1994 General maintainability program for material
GJB 450A-2004 General requirement for material reliability program
GJB 481 Welding quality control requirements
GJB 805.8-1990 General specification for ground support equipments of ground-to-ground strategic missile—Making, packing, transportation, storage
GJB 900 General program for system safety
GJB 3207 Human engineering requirements for military equipment and facilities
QJ 918 Bending radius of conduit
QJ 919A-1998 General technical conditions for acceptance of conduit manufacturing
QJ 1895 Technical conditions for installation, use and maintenance of hydraulic system of ground equipment
QJ 2243 Naming method of ground equipment products
SH 0358-1995 No.10 aviation hydraulic oil
3 Requirements
3.1 General
The vehicle shall meet all requirements specified in this specification and detailed specifications. If the requirements of this specification are inconsistent with the detailed specifications, the latter shall prevail.
3.2 Weight
Self-weight of vehicle with load capacity of 1t shall be no more than 3t, and that of vehicle with load capacity of 1t or higher is generally no more than twice the load capacity.
3.3 Colours
Generally, the colour of the vehicle is military green or camouflage color.
3.4 Appearance quality
The appearance of the vehicle shall meet the following requirements:
a) The vehicle shall be neat and beautiful, and the surface shall not have defects such as acute angle, sharp edge, rust, crack, deformation and breakage;
b) The welding seam is uniform, and the welding quality shall comply with the drawing and GJB 481;
c) The metal coating is in good condition, the precision grade, colour, gloss and uniformity of the topcoat shall meet the requirements of relevant detailed specifications, and the topcoat shall be free from flow marks, bubbles and peeling off;
d) The arrangement of hydraulic pipelines and electrical cables shall be reasonable, orderly, fixed and reliable, and the hose connection shall be free from distortion;
e) Fasteners shall not be loose or fall off, and there is no leakage in the hydraulic system.
3.5 Signs and code
3.5.1 Signs
The signs shall be eye-catching, clear and lasting. Generally, the content of the sign shall include the code name, name, serial number, manufacturer and date of manufacture of the product.
3.5.2 Code
Code shall be short, generally no more than 15 characters, and meet the requirements of QJ 2243.
3.6 Design and structure
3.6.1 General requirements
The design of the vehicle shall meet the following basic requirements:
a) It shall meet the requirements of the assignment book or contract;
b) It can adapt to various aircraft stores and be kind of universal;
c) It has good maneuverability to meet the requirements of various narrow space environments of aircraft and apron;
d) While inheriting mature technology, try our best to adopt the "three-oriented" design;
e) While meeting the requirements of technical performance indicators, full consideration is given to its economy.
1 Scope
This specification specifies the requirements, quality assurance requirements and delivery preparation of the missile hooking vehicle of tactical missile (hereinafter referred to as “vehicle”).
This specification is applicable to the design, manufacture and acceptance of missile hooking vehicle of tactical missile, and the hooking equipment of other types of airborne weapons may also be implemented with reference.
2 Normative references
The following documents contain provisions which, through reference in this text, constitute provisions of this code. For dated reference, subsequent amendments to (excluding any corrigendum), or revisions of, any of these publications do not apply. However, parties to agreements based on this specification are encouraged to investigate the possibility of applying the most recent editions of the documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 191 Packaging—Pictorial marking for handling of goods
GB/T 3766-2001 Hydraulic fluid power—General rules relating to systems
GB 11118.1 Mineral oil type and synthetic hydrocarbon type hydraulic oil
GB/T 14039-2002 Hydraulic fluid power—Fluids—Method for coding the level of contamination by solid particles
GJB 4.11-1983 Environmental test of ship electronic equipment—Salt spray test
GJB 145A-1993 Specification of preservation packaging
GJB 150.3-1986 Environmental test methods for military equipments—High temperature test
GJB 150.4-1986 Environmental test methods for military equipments—Low temperature test
GJB 150.10-1986 Environmental test methods for military equipments—Fungus test
GJB 150.11-1986 Environmental test methods for military equipments—Salt fog test
GJB 368A-1994 General maintainability program for material
GJB 450A-2004 General requirement for material reliability program
GJB 481 Welding quality control requirements
GJB 805.8-1990 General specification for ground support equipments of ground-to-ground strategic missile—Making, packing, transportation, storage
GJB 900 General program for system safety
GJB 3207 Human engineering requirements for military equipment and facilities
QJ 918 Bending radius of conduit
QJ 919A-1998 General technical conditions for acceptance of conduit manufacturing
QJ 1895 Technical conditions for installation, use and maintenance of hydraulic system of ground equipment
QJ 2243 Naming method of ground equipment products
SH 0358-1995 No.10 aviation hydraulic oil
3 Requirements
3.1 General
The vehicle shall meet all requirements specified in this specification and detailed specifications. If the requirements of this specification are inconsistent with the detailed specifications, the latter shall prevail.
3.2 Weight
Self-weight of vehicle with load capacity of 1t shall be no more than 3t, and that of vehicle with load capacity of 1t or higher is generally no more than twice the load capacity.
3.3 Colours
Generally, the colour of the vehicle is military green or camouflage color.
3.4 Appearance quality
The appearance of the vehicle shall meet the following requirements:
a) The vehicle shall be neat and beautiful, and the surface shall not have defects such as acute angle, sharp edge, rust, crack, deformation and breakage;
b) The welding seam is uniform, and the welding quality shall comply with the drawing and GJB 481;
c) The metal coating is in good condition, the precision grade, colour, gloss and uniformity of the topcoat shall meet the requirements of relevant detailed specifications, and the topcoat shall be free from flow marks, bubbles and peeling off;
d) The arrangement of hydraulic pipelines and electrical cables shall be reasonable, orderly, fixed and reliable, and the hose connection shall be free from distortion;
e) Fasteners shall not be loose or fall off, and there is no leakage in the hydraulic system.
3.5 Signs and code
3.5.1 Signs
The signs shall be eye-catching, clear and lasting. Generally, the content of the sign shall include the code name, name, serial number, manufacturer and date of manufacture of the product.
3.5.2 Code
Code shall be short, generally no more than 15 characters, and meet the requirements of QJ 2243.
3.6 Design and structure
3.6.1 General requirements
The design of the vehicle shall meet the following basic requirements:
a) It shall meet the requirements of the assignment book or contract;
b) It can adapt to various aircraft stores and be kind of universal;
c) It has good maneuverability to meet the requirements of various narrow space environments of aircraft and apron;
d) While inheriting mature technology, try our best to adopt the "three-oriented" design;
e) While meeting the requirements of technical performance indicators, full consideration is given to its economy.
