This standard applies to metal-oxide surge arrester without gaps (hereinafter referred to as "arrester") designed to limit overvoltage on AC power system.
2 Normative References
The following documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, the parties who enter into agreement according to these specifications are encouraged to research whether the latest editions of these documentations are applied or not. For undated references, the latest edition of the referenced document is applicable to this standard.
GB/T 191-2000 "Packaging-Pictorial Marking for Handling of Goods" (eqv ISO 780:1997)
GB 311.1-1997 "Insulation Co-ordination for High Voltage Transmission and Distribution Equipment" (neq IEC 60071-1:1993)
GB/T 311.2-2002 "Insulation Co-ordination-Part 2: Application Guide forInsulation Co-ordination for High Voltage Transmission and Distribution Equipment" (eqv IEC 60071-2:1996)
GB/T 775.1-2000 "Test Method for Insulators-Part 1: General Test Methods"
GB/T 775.3-2006 "Test Method for Insulators-Part 3: Mechanical Test Methods"
GB/T 2423.17-1993 "Basic Environmental Testing Procedures for Electric and Electronic Products-Test Ka: Salt Mist Test Method" (eqv IEC 68-2-11:1981)
GB/T 2423.22-2002 "Environmental Testing for Electric and Electronic Products-Part 2: Test Methods-Test N: Change of Temperature" (IEC 60068-2-14:1984, IDT)
GB/T 2900.19-1994 "Electrotechnical Terminology-High-voltage Test Technique and Insulation Co-ordination"
GB 3906-2006 "Alternating-current Metal-enclosed Switchgear and Controlgear for Rated Voltages above 3.6kV and up to and Including 40.5kV" (IEC 62271-200:2003, MOD)
GB/T 4585-2004 "Artificial Pollution Tests on High-voltage Insulators to Be Used on A.c. Systems" (IEC 60507:1991, IDT)
GB/T 6553-2003 "Test Methods for Evaluating Resistance to Tracking and Erosion of Electrical Insulating Materials Used under Severe Ambient Conditions" (IEC 60587:1984, IDT)
GB/T 19519-2004 "Composite Insulators for A.c. Overhead Lines with a Nominal Voltage Greater than 1000V-Definitions,Test Methods and Acceptance Criteria" (IEC 61109:1992, MOD)
IEC 60068-2-42:2003 "Environmental Testing-Part 2-42: Tests-Test Kc: Sulphur Dioxide Test for Contacts and Connections"
IEC 60815:1986 "Guide for the Selection of Insulators in Respect of Polluted Conditions"
IEC 61166:1993 "High-voltage Alternating Current Circuit-breakers-Guide for Seismic Qualification of High-voltage Alternating Current Circuit-breakers"
CISPR 16-1:1999 "Specification for Radio Disturbance and Immunity Measuring Apparatus and Methods-Part 1: Radio Disturbance and Immunity Measuring Apparatus"
CISPR 18-2:1986 "Radio Interference Characteristics of Overhead Power Lines and High-voltage Equipment-Part 2: Methods of Measurement and Procedure for Determining Limits"
JB/T 7618-1994 "Leakage Test for Surge Arresters-Bath Method"
JB/T 9673-1999 "Packet of Insulators"
3 Terms and Definitions
For the purposes of this standard, the following terms and definitions apply.
The terms used in this standard shall comply with this standard, in addition, the rest shall comply with GB/T 2900.12-2008 and GB/T 2900.19-1994.
3.1
Metal-oxide surge arrester without gaps
Arrester having non-linear metal-oxide resistors connected in series and/or in parallel without any integrated series or parallel spark gaps.
3.2
Non-linear metal-oxide resistor
Part of the surge arrester which, by its non-linear voltage versus current characteristics, acts as a low resistance to overvoltages, thus limiting the voltage across the arrester terminals, and as a high resistance at normal power-frequency voltage (non-linear metal-oxide resistor, hereinafter referred to as "resistor").
3.3
Internal grading system of an arrester
Grading impedances, in particular grading capacitors connected in parallel to one single or to a group of non-linear metal-oxide resistors, to control the voltage distribution along the metal-oxide resistor stack.
3.4
Grading ring of an arrester
Metal part, usually circular in shape, mounted to modify electrostatically the voltage distribution along the arrester.
3.5
Section of an arrester
Complete, suitably assembled part of an arrester necessary to represent the behaviour of a complete arrester with respect to a particular test. A section of an arrester is not necessarily a unit of an arrester.
3.6
Unit of an arrester
Completely housed part of an arrester which may be connected in series and/or in parallel with other units to construct an arrester of higher rated voltage and/or higher nominal discharge current rating. A unit of an arrester is not necessarily a section of an arrester.
3.7
Pressure-relief device of an arrester
Means for relieving internal pressure in an arrester and preventing violent shattering of the housing following prolonged passage of fault current or internal flashover of the arrester.
Foreword I 1 Scope 2 Normative References 3 Terms and Definitions 4 Identification and Classification 4.1 Arrester Identification 4.2 Arrester Classification 5 Standard Ratings and Service Conditions 5.1 Standard Rated Voltages 5.2 Standard Rated Frequencies 5.3 Standard Nominal Discharge Currents 5.4 Service Conditions 6 Technical Requirements 6.1 Insulation Withstand of the Arrester Housing 6.2 Reference Voltage 6.3 Residual Voltages 6.4 Internal Partial Discharges 6.5 Sealing Performance of the Arrester 6.6 Current Distribution in a Multi-column Arrester 6.7 Thermal Stability 6.8 Long-duration Current Impulse Withstand 6.9 Operating Duty 6.10 Power-frequency Voltage Withstand versus Time Characteristics of an Arrester 6.11 Short-circuit Test 6.12 Disconnector 6.13 Requirements for Arrester Accessories 6.14 Mechanical Loads of an Arrester 6.15 Electromagnetic Compatibility 6.16 End of Life 6.17 Lightning Impulse Discharge Capability 6.18 Continuous Current of an Arrester 6.19 Leak Current at 0.75 Ud.c.ref 6.20 High Current Impulse Withstand 6.21 Pollution Resistance of an Arrester 6.22 Packing, Transport and Keeping of an Arrester 7 Test Requirements 7.1 Measuring Equipment and Accuracy 7.2 Test Samples 8 Type Tests (Design Tests) 8.1 General 8.2 Insulation Withstand Tests on the Arrester Housing 8.3 Residual Voltage Tests 8.4 Long-duration Current Impulse Withstand Test 8.5 Operating Duty Tests 8.6 Tests of Arrester Disconnectors/Fault Indicators 8.7 Short-circuit Tests 8.8 Internal Partial Discharge Tests 8.9 Test of the Bending Load 8.10 Environmental Tests 8.11 Seal Leak Rate Test 8.12 Radio Interference Voltage (RIV) Test 8.13 Artificial Pollution Test 8.14 Continuous Current Test 8.15 Power-frequency Reference Voltage Test 8.16 DC Reference Voltage Test 8.17 Leak Current Test at 0.75 Ud.c.ref 8.18 Current Distribution Test for Multi-column Arrester 8.19 High Current Impulse Withstand Test 9 Routine Tests, Acceptance Tests, Periodic Tests and Sample Tests 9.1 Routine Tests 9.2 Acceptance Tests 9.3 Periodic Tests 9.4 Sample Test 10 Polymer-housed Arrester 10.1 Scope 10.2 Normative References 10.3 Terms and Definitions 10.4 Identification and Classification 10.5 Standard Ratings and Service Conditions 10.6 Technical Requirements 10.7 Test Requirements 10.8 Type Tests (Design tests) 10.9 Routine Tests, Acceptance Tests, Periodic Tests and Sample Tests 11 Test Requirements on Gas-insulated Metal Enclosed Arresters (GIS-arresters) 11.1 Scope 11.2 Normative References 11.3 Terms and Definitions 11.4 Identification and Classification 11.5 Standard Ratings and Service Conditions 11.6 Requirements 11.7 Test Requirements 11.8 Type Test (Design Tests) 11.9 Routine Tests, Acceptance Tests, Periodic Tests and Sample Tests 11.10 Test after Erection on Site 12 Separable and Dead-front Arresters 12.1 Scope 12.2 Normative References 12.3 Terms and Definitions 12.4 Identification and Classification 12.5 Standard Ratings and Service Conditions 12.6 Requirements 12.7 Test Requirements 12.8 Type Tests (Design Tests) 12.9 Routine Tests, Acceptance Tests, Periodic Tests and Sample Tests 13 Liquid-immersed Arresters 13.1 Scope 13.2 Normative References 13.3 Terms and Definitions 13.4 Identification and Classification 13.5 Standard Ratings and Service Conditions 13.6 Requirements 13.7 General Testing Procedure 13.8 Type Tests (Design Tests) 13.9 Routine Tests, Acceptance Tests, Periodic Tests and Sample Tests Annex A (Normative) Abnormal Service Conditions Annex B (Normative) Test to Verify Thermal Equivalency between Complete Arrester and Arrester Section Annex C (Normative) Requirements for High Lightning Duty Arresters for Voltage Range 1kV to 52kV Annex D (Normative) Procedure to Verify the Power-frequency Voltage-versus-time Characteristics of an Arrester Annex E (Informative) Guide to Selection of Line Discharge Class Annex F (Normative) Artificial Pollution Test with Respect to the Thermal Stress on Porcelain-housed Multi-unit Metal-oxide Surge Arresters F.1 Glossary F.2 General F.3 Classification of Site Severity F.4 Preliminary Heating Test: Measurement of the Thermal Time Constant τ and Calculation of β F.5 Verification of the Need to Perform the Pollution Tests F.6 General Requirements for the Pollution Test F.7 Test Procedures F.8 Evaluation of Test Results F.9 Example Annex G (Informative) Typical Information Given with Enquiries and Tenders G.1 Information Given with Enquiry G.2 Information Given with Tender Annex H (Informative) Typical Circuit for High Current Impulse Operating Duty Test Annex I (Informative) Typical Circuit for a Distributed Constant Impulse Generator for the Long Duration Current Impulse Withstand Test Annex J (Normative) Typical Maximum Residual Voltages Annex K (Informative) Ageing Test Procedure-Arrhenius law-Problems with Higher Temperatures Annex L (Informative) Guide for the Determination of the Voltage Distribution along Metal-oxide Surge Arresters L.1 General L.2 Modelling of the Surge Arrester L.3 Modelling of the Boundary Conditions L.4 Calculation Procedures L.5 Example of Calculation Annex M (Normative) Mechanical Considerations M.1 Test of Bending Moment M.2 Seismic Test M.3 Definition of Mechanical Loads M.4 Definition of Seal Leak Rate M.5 Calculation of Wind-bending-moment Annex N (Normative) Test procedure to Determine the Lightning Impulse Discharge Capability N.1 General N.2 Selection of Test Samples N.3 Test Procedure N.4 Test Parameters for the Lightning Impulse Discharge Capability Test N.5 Measurements during the Lightning Impulse Discharge Capability Test N.6 Rated Lightning Impulse Discharge Capability N.7 List of Rated Energy Values N.8 List of Rated Charge Values Annex O (Informative) Artificial Pollution Test Methods O.1 Pollution Classification O.2 Test O.3 Test Evaluation Annex P (Informative) Packing, Transport and Storage P.1 Packing P.2 Technical Document Provided along with Products P.3 Transport and Storage Annex Q (Informative) Main Technical Differences and their Reasons between this Standard and IEC 60099-4: Annex R (Informative) Comparison between This Standard and IEC 60099-4:2006 in Terms of Chapter and Article Numbers
1 Scope
This standard applies to metal-oxide surge arrester without gaps (hereinafter referred to as "arrester") designed to limit overvoltage on AC power system.
2 Normative References
The following documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, the parties who enter into agreement according to these specifications are encouraged to research whether the latest editions of these documentations are applied or not. For undated references, the latest edition of the referenced document is applicable to this standard.
GB/T 191-2000 "Packaging-Pictorial Marking for Handling of Goods" (eqv ISO 780:1997)
GB 311.1-1997 "Insulation Co-ordination for High Voltage Transmission and Distribution Equipment" (neq IEC 60071-1:1993)
GB/T 311.2-2002 "Insulation Co-ordination-Part 2: Application Guide forInsulation Co-ordination for High Voltage Transmission and Distribution Equipment" (eqv IEC 60071-2:1996)
GB/T 775.1-2000 "Test Method for Insulators-Part 1: General Test Methods"
GB/T 775.3-2006 "Test Method for Insulators-Part 3: Mechanical Test Methods"
GB/T 2423.17-1993 "Basic Environmental Testing Procedures for Electric and Electronic Products-Test Ka: Salt Mist Test Method" (eqv IEC 68-2-11:1981)
GB/T 2423.22-2002 "Environmental Testing for Electric and Electronic Products-Part 2: Test Methods-Test N: Change of Temperature" (IEC 60068-2-14:1984, IDT)
GB/T 2900.12-2008 "Electrotechnical Terminology-Surge Arresters, Low-voltage Surge Protective Devices and Components"
GB/T 2900.19-1994 "Electrotechnical Terminology-High-voltage Test Technique and Insulation Co-ordination"
GB 3906-2006 "Alternating-current Metal-enclosed Switchgear and Controlgear for Rated Voltages above 3.6kV and up to and Including 40.5kV" (IEC 62271-200:2003, MOD)
GB/T 4585-2004 "Artificial Pollution Tests on High-voltage Insulators to Be Used on A.c. Systems" (IEC 60507:1991, IDT)
GB/T 6553-2003 "Test Methods for Evaluating Resistance to Tracking and Erosion of Electrical Insulating Materials Used under Severe Ambient Conditions" (IEC 60587:1984, IDT)
GB/T 7354-2003 "Partial Discharge Measurements" (IEC 60270:2000, IDT)
GB 7674-1997 "Gas-insulated Metal-enclosed Switchgear for Rated Voltages of 72.5 kV and above" (IEC 60517:1990, MOD)
GB/T 8905-1996 "The Guide for Processing and Measuring SF6 Gas in Power Apparatus" (IEC 60480:1974, neq; IEC 60376:1971, neq)
GB/T 11023-1989 "Test Guide of SF6 Gas Tightness for High-voltage Switchgear"
GB/T 16927.1-1997 "Hign Voltage Test Techniques-Part 1: General Test Requirements" (eqv IEC 60060-1:1989)
GB/T 16927.2-1997 "High Voltage Test Techniques-Part 2: Measuring Systems" (eqv IEC 60060-2:1994)
GB/T 17467-1998 "High-voltage/Low-voltage Prefabricated Substations" (eqv IEC 61330:1995)
GB/T 19519-2004 "Composite Insulators for A.c. Overhead Lines with a Nominal Voltage Greater than 1000V-Definitions,Test Methods and Acceptance Criteria" (IEC 61109:1992, MOD)
IEC 60068-2-42:2003 "Environmental Testing-Part 2-42: Tests-Test Kc: Sulphur Dioxide Test for Contacts and Connections"
IEC 60815:1986 "Guide for the Selection of Insulators in Respect of Polluted Conditions"
IEC 61166:1993 "High-voltage Alternating Current Circuit-breakers-Guide for Seismic Qualification of High-voltage Alternating Current Circuit-breakers"
CISPR 16-1:1999 "Specification for Radio Disturbance and Immunity Measuring Apparatus and Methods-Part 1: Radio Disturbance and Immunity Measuring Apparatus"
CISPR 18-2:1986 "Radio Interference Characteristics of Overhead Power Lines and High-voltage Equipment-Part 2: Methods of Measurement and Procedure for Determining Limits"
JB/T 7618-1994 "Leakage Test for Surge Arresters-Bath Method"
JB/T 9673-1999 "Packet of Insulators"
3 Terms and Definitions
For the purposes of this standard, the following terms and definitions apply.
The terms used in this standard shall comply with this standard, in addition, the rest shall comply with GB/T 2900.12-2008 and GB/T 2900.19-1994.
3.1
Metal-oxide surge arrester without gaps
Arrester having non-linear metal-oxide resistors connected in series and/or in parallel without any integrated series or parallel spark gaps.
3.2
Non-linear metal-oxide resistor
Part of the surge arrester which, by its non-linear voltage versus current characteristics, acts as a low resistance to overvoltages, thus limiting the voltage across the arrester terminals, and as a high resistance at normal power-frequency voltage (non-linear metal-oxide resistor, hereinafter referred to as "resistor").
3.3
Internal grading system of an arrester
Grading impedances, in particular grading capacitors connected in parallel to one single or to a group of non-linear metal-oxide resistors, to control the voltage distribution along the metal-oxide resistor stack.
3.4
Grading ring of an arrester
Metal part, usually circular in shape, mounted to modify electrostatically the voltage distribution along the arrester.
3.5
Section of an arrester
Complete, suitably assembled part of an arrester necessary to represent the behaviour of a complete arrester with respect to a particular test. A section of an arrester is not necessarily a unit of an arrester.
3.6
Unit of an arrester
Completely housed part of an arrester which may be connected in series and/or in parallel with other units to construct an arrester of higher rated voltage and/or higher nominal discharge current rating. A unit of an arrester is not necessarily a section of an arrester.
3.7
Pressure-relief device of an arrester
Means for relieving internal pressure in an arrester and preventing violent shattering of the housing following prolonged passage of fault current or internal flashover of the arrester.
Contents of GB 11032-2010
Foreword I
1 Scope
2 Normative References
3 Terms and Definitions
4 Identification and Classification
4.1 Arrester Identification
4.2 Arrester Classification
5 Standard Ratings and Service Conditions
5.1 Standard Rated Voltages
5.2 Standard Rated Frequencies
5.3 Standard Nominal Discharge Currents
5.4 Service Conditions
6 Technical Requirements
6.1 Insulation Withstand of the Arrester Housing
6.2 Reference Voltage
6.3 Residual Voltages
6.4 Internal Partial Discharges
6.5 Sealing Performance of the Arrester
6.6 Current Distribution in a Multi-column Arrester
6.7 Thermal Stability
6.8 Long-duration Current Impulse Withstand
6.9 Operating Duty
6.10 Power-frequency Voltage Withstand versus Time Characteristics of an Arrester
6.11 Short-circuit Test
6.12 Disconnector
6.13 Requirements for Arrester Accessories
6.14 Mechanical Loads of an Arrester
6.15 Electromagnetic Compatibility
6.16 End of Life
6.17 Lightning Impulse Discharge Capability
6.18 Continuous Current of an Arrester
6.19 Leak Current at 0.75 Ud.c.ref
6.20 High Current Impulse Withstand
6.21 Pollution Resistance of an Arrester
6.22 Packing, Transport and Keeping of an Arrester
7 Test Requirements
7.1 Measuring Equipment and Accuracy
7.2 Test Samples
8 Type Tests (Design Tests)
8.1 General
8.2 Insulation Withstand Tests on the Arrester Housing
8.3 Residual Voltage Tests
8.4 Long-duration Current Impulse Withstand Test
8.5 Operating Duty Tests
8.6 Tests of Arrester Disconnectors/Fault Indicators
8.7 Short-circuit Tests
8.8 Internal Partial Discharge Tests
8.9 Test of the Bending Load
8.10 Environmental Tests
8.11 Seal Leak Rate Test
8.12 Radio Interference Voltage (RIV) Test
8.13 Artificial Pollution Test
8.14 Continuous Current Test
8.15 Power-frequency Reference Voltage Test
8.16 DC Reference Voltage Test
8.17 Leak Current Test at 0.75 Ud.c.ref
8.18 Current Distribution Test for Multi-column Arrester
8.19 High Current Impulse Withstand Test
9 Routine Tests, Acceptance Tests, Periodic Tests and Sample Tests
9.1 Routine Tests
9.2 Acceptance Tests
9.3 Periodic Tests
9.4 Sample Test
10 Polymer-housed Arrester
10.1 Scope
10.2 Normative References
10.3 Terms and Definitions
10.4 Identification and Classification
10.5 Standard Ratings and Service Conditions
10.6 Technical Requirements
10.7 Test Requirements
10.8 Type Tests (Design tests)
10.9 Routine Tests, Acceptance Tests, Periodic Tests and Sample Tests
11 Test Requirements on Gas-insulated Metal Enclosed Arresters (GIS-arresters)
11.1 Scope
11.2 Normative References
11.3 Terms and Definitions
11.4 Identification and Classification
11.5 Standard Ratings and Service Conditions
11.6 Requirements
11.7 Test Requirements
11.8 Type Test (Design Tests)
11.9 Routine Tests, Acceptance Tests, Periodic Tests and Sample Tests
11.10 Test after Erection on Site
12 Separable and Dead-front Arresters
12.1 Scope
12.2 Normative References
12.3 Terms and Definitions
12.4 Identification and Classification
12.5 Standard Ratings and Service Conditions
12.6 Requirements
12.7 Test Requirements
12.8 Type Tests (Design Tests)
12.9 Routine Tests, Acceptance Tests, Periodic Tests and Sample Tests
13 Liquid-immersed Arresters
13.1 Scope
13.2 Normative References
13.3 Terms and Definitions
13.4 Identification and Classification
13.5 Standard Ratings and Service Conditions
13.6 Requirements
13.7 General Testing Procedure
13.8 Type Tests (Design Tests)
13.9 Routine Tests, Acceptance Tests, Periodic Tests and Sample Tests
Annex A (Normative) Abnormal Service Conditions
Annex B (Normative) Test to Verify Thermal Equivalency between Complete Arrester and Arrester Section
Annex C (Normative) Requirements for High Lightning Duty Arresters for Voltage Range 1kV to 52kV
Annex D (Normative) Procedure to Verify the Power-frequency Voltage-versus-time Characteristics of an Arrester
Annex E (Informative) Guide to Selection of Line Discharge Class
Annex F (Normative) Artificial Pollution Test with Respect to the Thermal Stress on Porcelain-housed Multi-unit Metal-oxide Surge Arresters
F.1 Glossary
F.2 General
F.3 Classification of Site Severity
F.4 Preliminary Heating Test: Measurement of the Thermal Time Constant τ and Calculation of β
F.5 Verification of the Need to Perform the Pollution Tests
F.6 General Requirements for the Pollution Test
F.7 Test Procedures
F.8 Evaluation of Test Results
F.9 Example
Annex G (Informative) Typical Information Given with Enquiries and Tenders
G.1 Information Given with Enquiry
G.2 Information Given with Tender
Annex H (Informative) Typical Circuit for High Current Impulse Operating Duty Test
Annex I (Informative) Typical Circuit for a Distributed Constant Impulse Generator for the Long Duration Current Impulse Withstand Test
Annex J (Normative) Typical Maximum Residual Voltages
Annex K (Informative) Ageing Test Procedure-Arrhenius law-Problems with Higher Temperatures
Annex L (Informative) Guide for the Determination of the Voltage Distribution along Metal-oxide Surge Arresters
L.1 General
L.2 Modelling of the Surge Arrester
L.3 Modelling of the Boundary Conditions
L.4 Calculation Procedures
L.5 Example of Calculation
Annex M (Normative) Mechanical Considerations
M.1 Test of Bending Moment
M.2 Seismic Test
M.3 Definition of Mechanical Loads
M.4 Definition of Seal Leak Rate
M.5 Calculation of Wind-bending-moment
Annex N (Normative) Test procedure to Determine the Lightning Impulse Discharge Capability
N.1 General
N.2 Selection of Test Samples
N.3 Test Procedure
N.4 Test Parameters for the Lightning Impulse Discharge Capability Test
N.5 Measurements during the Lightning Impulse Discharge Capability Test
N.6 Rated Lightning Impulse Discharge Capability
N.7 List of Rated Energy Values
N.8 List of Rated Charge Values
Annex O (Informative) Artificial Pollution Test Methods
O.1 Pollution Classification
O.2 Test
O.3 Test Evaluation
Annex P (Informative) Packing, Transport and Storage
P.1 Packing
P.2 Technical Document Provided along with Products
P.3 Transport and Storage
Annex Q (Informative) Main Technical Differences and their Reasons between this Standard and IEC 60099-4:
Annex R (Informative) Comparison between This Standard and IEC 60099-4:2006 in Terms of Chapter and Article Numbers
