GB 5009.168-2026 National food safety standard -Determination of fatty acids and trans fatty acids in foods
1 Scope
This standard specifies the method for the determination of fatty acids and trans fatty acids in foods (excluding foods for special dietary uses).
Method I (internal standard method) and Method II (external standard method) are applicable to the determination of fatty acids and trans fatty acids in foods.
Method III (normalization method) is applicable to the determination of fatty acid composition in oils and fats, as well as saturated fat and trans fat in foods.
Method I Internal standard method
2 Principle
Boron trifluoride‑methanol method and potassium hydroxide‑methanol method: After adding the internal standard to the oil and fat specimen, methyl esterification is carried out directly under alkaline conditions. For other specimens, after adding the internal standard, fat is extracted by hydrolysis, followed by methyl esterification under alkaline conditions. The resulting fatty acid methyl esters are analyzed by gas chromatography and quantified by the internal standard method.
Acetyl chloride‑methanol method: Fat and free fatty acids in the specimen are subjected to methyl esterification under the action of hydrochloric acid‑methanol generated from the reaction of acetyl chloride with methanol. The resulting fatty acid methyl esters are analyzed by gas chromatography and quantified by the internal standard method.
3 Reagents and materials
Unless otherwise specified, analytically-pure reagents and Class-I water as specified in GB/T 6682 are adopted for the purpose of this method.
3.1 Reagents
3.1.1 Iodine (I2).
3.1.2 Potassium iodide (KI).
3.1.3 Hydrochloric acid (HCl).
3.1.4 Diethyl ether (C4H10O).
3.1.5 Petroleum ether (CnH2n+2): with a boiling range of 30℃ to 60℃.
3.1.6 Methanol (CH4O): chromatographically pure.
3.1.7 Sodium hydroxide (NaOH).
3.1.8 Sodium chloride (NaCl).
3.1.9 Potassium hydroxide (KOH): ≥85%.
3.1.10 Acetyl chloride (C2H3ClO).
3.1.11 Anhydrous sodium carbonate (Na2CO3).
3.1.12 N-hexane (C6H14): chromatographically pure.
3.1.13 α-amylase: with an enzyme activity of ≥ 1.5 U/mg.
3.1.14 Ammonia solution (NH3·H2O).
3.1.15 Ethanol (C2H6O): ≥95%.
3.1.16 Boron trifluoride methanol solution: 14%.
3.1.17 N-heptane (C7H16): chromatographically pure.
3.1.18 Anhydrous sodium sulfate (Na2SO4).
3.1.19 Isooctane (C8H18): chromatographically pure.
3.1.20 Toluene (C7H8): chromatographically pure.
3.1.21 Sodium bisulfate (NaHSO4).
3.2 Preparation of reagents
3.2.1 Iodine solution (0.1 mol/L): Weigh 12.7 g of iodine and 25 g of potassium iodide, dissolve with water and make up to 1 000 mL.
3.2.2 Hydrochloric acid solution (8.3 mol/L): Measure 347 mL of hydrochloric acid, make up to 500 mL with water and mix well.
Contents
Foreword II
1 Scope
2 Principle
3 Reagents and materials
4 Apparatus
5 Analytical procedure
6 Expression of analysis results
7 Precision
8 Others
9 Principle
10 Reagents and materials
11 Apparatus
12 Analytical procedure
13 Expression of analysis results
14 Precision
15 Others
16 Principle
17 Reagents and materials
18 Apparatus
19 Analytical procedure
20 Expression of analysis results
21 Precision
22 Others
Annex A Information of fatty acid reference material
Annex B Reference retention time and relative retention time of fatty acid methyl esters
Annex C Chromatogram of fatty acid methyl ester standard solution
Annex D Conversion factors among fatty acid methyl esters, fatty acids and fatty acid triglycerides
Annex E Calculation of FID calibration factors
GB 5009.168-2026 National food safety standard -Determination of fatty acids and trans fatty acids in foods
1 Scope
This standard specifies the method for the determination of fatty acids and trans fatty acids in foods (excluding foods for special dietary uses).
Method I (internal standard method) and Method II (external standard method) are applicable to the determination of fatty acids and trans fatty acids in foods.
Method III (normalization method) is applicable to the determination of fatty acid composition in oils and fats, as well as saturated fat and trans fat in foods.
Method I Internal standard method
2 Principle
Boron trifluoride‑methanol method and potassium hydroxide‑methanol method: After adding the internal standard to the oil and fat specimen, methyl esterification is carried out directly under alkaline conditions. For other specimens, after adding the internal standard, fat is extracted by hydrolysis, followed by methyl esterification under alkaline conditions. The resulting fatty acid methyl esters are analyzed by gas chromatography and quantified by the internal standard method.
Acetyl chloride‑methanol method: Fat and free fatty acids in the specimen are subjected to methyl esterification under the action of hydrochloric acid‑methanol generated from the reaction of acetyl chloride with methanol. The resulting fatty acid methyl esters are analyzed by gas chromatography and quantified by the internal standard method.
3 Reagents and materials
Unless otherwise specified, analytically-pure reagents and Class-I water as specified in GB/T 6682 are adopted for the purpose of this method.
3.1 Reagents
3.1.1 Iodine (I2).
3.1.2 Potassium iodide (KI).
3.1.3 Hydrochloric acid (HCl).
3.1.4 Diethyl ether (C4H10O).
3.1.5 Petroleum ether (CnH2n+2): with a boiling range of 30℃ to 60℃.
3.1.6 Methanol (CH4O): chromatographically pure.
3.1.7 Sodium hydroxide (NaOH).
3.1.8 Sodium chloride (NaCl).
3.1.9 Potassium hydroxide (KOH): ≥85%.
3.1.10 Acetyl chloride (C2H3ClO).
3.1.11 Anhydrous sodium carbonate (Na2CO3).
3.1.12 N-hexane (C6H14): chromatographically pure.
3.1.13 α-amylase: with an enzyme activity of ≥ 1.5 U/mg.
3.1.14 Ammonia solution (NH3·H2O).
3.1.15 Ethanol (C2H6O): ≥95%.
3.1.16 Boron trifluoride methanol solution: 14%.
3.1.17 N-heptane (C7H16): chromatographically pure.
3.1.18 Anhydrous sodium sulfate (Na2SO4).
3.1.19 Isooctane (C8H18): chromatographically pure.
3.1.20 Toluene (C7H8): chromatographically pure.
3.1.21 Sodium bisulfate (NaHSO4).
3.2 Preparation of reagents
3.2.1 Iodine solution (0.1 mol/L): Weigh 12.7 g of iodine and 25 g of potassium iodide, dissolve with water and make up to 1 000 mL.
3.2.2 Hydrochloric acid solution (8.3 mol/L): Measure 347 mL of hydrochloric acid, make up to 500 mL with water and mix well.
Contents of GB 5009.168-2026
Contents
Foreword II
1 Scope
2 Principle
3 Reagents and materials
4 Apparatus
5 Analytical procedure
6 Expression of analysis results
7 Precision
8 Others
9 Principle
10 Reagents and materials
11 Apparatus
12 Analytical procedure
13 Expression of analysis results
14 Precision
15 Others
16 Principle
17 Reagents and materials
18 Apparatus
19 Analytical procedure
20 Expression of analysis results
21 Precision
22 Others
Annex A Information of fatty acid reference material
Annex B Reference retention time and relative retention time of fatty acid methyl esters
Annex C Chromatogram of fatty acid methyl ester standard solution
Annex D Conversion factors among fatty acid methyl esters, fatty acids and fatty acid triglycerides
Annex E Calculation of FID calibration factors