1 Scope
This standard specifies test methods for the asynchronous generator for grid-connected wind turbine generator systems.
This standard is applicable to the performance test for the asynchronous generator (hereinafter referred to as "generator") with single speed or double speed for grid-connected wind turbine generator systems.
2 Normative References
The following standards contain provisions which, through reference in this part of GB/T 19071, constitute provisions of this part. For dated references, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, the parties who enter into agreement according to this standard are encouraged to study whether the latest editions of these documents apply. For undated references, the latest edition applies to this part.
GB 755 Rotating Electrical Machines - Rating and Performance (idt IEC 60034-1: 1996)
GB/T 1032 Test Methods for Three-phase Asynchronous Motor
GB/T 4942.1 Classification of Degrees of Protection Provided by Enclosures of Rotating Electrical Machines (IP Code) (idt IEC 60034-5: 1991)
GB 10068-2000 Mechanical Vibration of Certain Machines with Shaft Heights of 56mm and Higher – Measurement, Evaluation and Limit Value of Vibration (idt IEC 60034-14: 1996)
GB/T 10069.1 The Determination Method and Limit Value for Noise of Rotating Electrical Machines - the Determination Method of Noise Engineering (neq ISO 1680-1: 1986)
GB/T 10069.2 The Determination Method and Limit Value for Noise of Rotating Electrical Machines - the Simple Determination Method of Noise (neq ISO 1680-2: 1986)
GB 10069.3 The Determination Method and Limit Value for Noise of Rotating Electrical Machines - Noise Limit Value (neq IEC 60034-9)
GB/T 12665-1990 Requirements of Damp-heat Testing for Electrical Machines Used in General Environmental Conditions
3 Test Requirements and Preparations
3.1 The requirements of test power supply shall comply with those specified in GB/T 1032.
3.2 The selection of measuring instruments shall comply with those specified in GB/T 1032.
3.3 The measurement requirements shall comply with those specified in GB/T 1032.
3.4 Preparations before the test shall comply with those specified in GB/T 1032.
Foreword i
1 Scope
2 Normative References
3 Test Requirements and Preparations
4 Test Items and Test Methods
1 Scope
This standard specifies test methods for the asynchronous generator for grid-connected wind turbine generator systems.
This standard is applicable to the performance test for the asynchronous generator (hereinafter referred to as "generator") with single speed or double speed for grid-connected wind turbine generator systems.
2 Normative References
The following standards contain provisions which, through reference in this part of GB/T 19071, constitute provisions of this part. For dated references, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, the parties who enter into agreement according to this standard are encouraged to study whether the latest editions of these documents apply. For undated references, the latest edition applies to this part.
GB 755 Rotating Electrical Machines - Rating and Performance (idt IEC 60034-1: 1996)
GB/T 1032 Test Methods for Three-phase Asynchronous Motor
GB/T 4942.1 Classification of Degrees of Protection Provided by Enclosures of Rotating Electrical Machines (IP Code) (idt IEC 60034-5: 1991)
GB 10068-2000 Mechanical Vibration of Certain Machines with Shaft Heights of 56mm and Higher – Measurement, Evaluation and Limit Value of Vibration (idt IEC 60034-14: 1996)
GB/T 10069.1 The Determination Method and Limit Value for Noise of Rotating Electrical Machines - the Determination Method of Noise Engineering (neq ISO 1680-1: 1986)
GB/T 10069.2 The Determination Method and Limit Value for Noise of Rotating Electrical Machines - the Simple Determination Method of Noise (neq ISO 1680-2: 1986)
GB 10069.3 The Determination Method and Limit Value for Noise of Rotating Electrical Machines - Noise Limit Value (neq IEC 60034-9)
GB/T 12665-1990 Requirements of Damp-heat Testing for Electrical Machines Used in General Environmental Conditions
3 Test Requirements and Preparations
3.1 The requirements of test power supply shall comply with those specified in GB/T 1032.
3.2 The selection of measuring instruments shall comply with those specified in GB/T 1032.
3.3 The measurement requirements shall comply with those specified in GB/T 1032.
3.4 Preparations before the test shall comply with those specified in GB/T 1032.
Contents of GB/T 19071.2-2003
Foreword i
1 Scope
2 Normative References
3 Test Requirements and Preparations
4 Test Items and Test Methods