Structure, main size and basic parameters of one piece glass-lined steel vessels with agitator
1 Scope
This standard specifies the definition, structure, main size, basic parameters and marks of one piece glass-lined vessels with agitator (hereinafter referred as "the vessel").
This standard is applicable to one piece glass-lined vessels with agitators with the design pressure less than or equal to 1.0 MPa, the nominal volume of 1000 L ~ 40000 L, the design pressure less than or equal to 0.6 MPa in U-shaped jacket, and the design temperature higher than -20 °C ~ 200 °C in inner container and jacket.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendment) applies.
GB 25025 Specification for glass-lined equipment for industry
HG/T 2048.1 Glass-lined stuffing boxes
HG/T 2050 Gaskets for glass-lined steel vessel
HG/T 2051.3 Glass-lined agitator retreat curve impeller type
HG/T 2051.4 Glass-lined agitator pitch blade turbine type
HG/T 2052 Drive for glass-lined vessel with agitator
HG/T 2054 Clamps for glass lined vessels
HG/T 2055.1 Manhole for glass lined steel vessel
HG/T 2055.2 Glass-lined manhole with sight glass
HG/T 2057 Stirred glass lined vessel mechanical seals
HG/T 2058.1 Glass-lined thermometer tube
HG/T 2058.2 Thermometer tube of the glass-lined baffle
HG/T 2143 Glass-lined steel vessel - nozzles
HG/T 3217 Glass-lined lift up valves
HG/T 3218 Glass-lined lift down valves
HG/T 20592 Steel pipe flanges (PN designated)
JB/T 4712.3 Vessel supports - Part 3: Lug support
JB/T 4712.4 Vessel supports - Part 4: Bracket support
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
capacity for under agitator flanged or agitator nozzles
refers to the volume below the flange if the upper head of the vessel is equipped with an equipment flange or to the volume below the stirring shaft hole if the upper head of the vessel is not equipped with the equipment flange
4 Structure and classification
The vessels are divided into F-structure and Q-structure according to the different structures of upper heads, as shown in Figure 1. The upper heads of the vessels are provided with equipment flanges, and those with the nominal diameter of their equipment flanges of less than half of the nominal diameter of the vessels fall into F-structure, while those without equipment flanges on their upper heads belong to Q-structure.
Forword i
1 Scope
2 Normative references
3 Terms and definitions
4 Structure and classification
5 Main size and parameters
6 Marking and example thereof
Structure, main size and basic parameters of one piece glass-lined steel vessels with agitator
1 Scope
This standard specifies the definition, structure, main size, basic parameters and marks of one piece glass-lined vessels with agitator (hereinafter referred as "the vessel").
This standard is applicable to one piece glass-lined vessels with agitators with the design pressure less than or equal to 1.0 MPa, the nominal volume of 1000 L ~ 40000 L, the design pressure less than or equal to 0.6 MPa in U-shaped jacket, and the design temperature higher than -20 °C ~ 200 °C in inner container and jacket.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendment) applies.
GB 25025 Specification for glass-lined equipment for industry
HG/T 2048.1 Glass-lined stuffing boxes
HG/T 2050 Gaskets for glass-lined steel vessel
HG/T 2051.3 Glass-lined agitator retreat curve impeller type
HG/T 2051.4 Glass-lined agitator pitch blade turbine type
HG/T 2052 Drive for glass-lined vessel with agitator
HG/T 2054 Clamps for glass lined vessels
HG/T 2055.1 Manhole for glass lined steel vessel
HG/T 2055.2 Glass-lined manhole with sight glass
HG/T 2057 Stirred glass lined vessel mechanical seals
HG/T 2058.1 Glass-lined thermometer tube
HG/T 2058.2 Thermometer tube of the glass-lined baffle
HG/T 2143 Glass-lined steel vessel - nozzles
HG/T 3217 Glass-lined lift up valves
HG/T 3218 Glass-lined lift down valves
HG/T 20592 Steel pipe flanges (PN designated)
JB/T 4712.3 Vessel supports - Part 3: Lug support
JB/T 4712.4 Vessel supports - Part 4: Bracket support
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
capacity for under agitator flanged or agitator nozzles
refers to the volume below the flange if the upper head of the vessel is equipped with an equipment flange or to the volume below the stirring shaft hole if the upper head of the vessel is not equipped with the equipment flange
4 Structure and classification
The vessels are divided into F-structure and Q-structure according to the different structures of upper heads, as shown in Figure 1. The upper heads of the vessels are provided with equipment flanges, and those with the nominal diameter of their equipment flanges of less than half of the nominal diameter of the vessels fall into F-structure, while those without equipment flanges on their upper heads belong to Q-structure.
Contents of GB/T 25026-2017
Forword i
1 Scope
2 Normative references
3 Terms and definitions
4 Structure and classification
5 Main size and parameters
6 Marking and example thereof