1 Scope
This standard specifies the technical requirements, measurement methods, evaluation methods and inspection rules for the vibration (velocity) of deep groove ball bearings of diameter series 0, 2, 3 (hereinafter referred to as bearings) with the nominal external diameter greater than 10 mm to 200 mm and the boundary dimensions conforming to GB/T 276.
This standard is applicable to deep groove ball bearings. Group V specified in this standard is the basic requirement for vibration (velocity) of general bearing; Groups V1, V2, V3, V4 and VF3, VF4 are applicable to the bearings with higher vibration (velocity) requirements, and Groups VF3 and VF4 group are only applicable to the bearings with a nominal external diameter of more than 10 mm to 100 mm.
2 Normative References
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 276 Rolling Bearings — Deep Groove Ball Bearings — Boundary Dimensions
GB 443 Lubricating Oils for Total Loss Systems L-AN
GB/T 2828.1 Sampling Procedures for Inspection by Attributes — Part 1: Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-lot Inspection
GB/T 24610.1 Rolling Bearings — Measuring Methods for Vibration — Part 1: Fundamentals
GB/T 24610.2 Rolling Bearings — Measuring Methods for Vibration — Part 2: Radial Ball Bearings with Cylindrical Bore and Outside Surface
JB/T 2974 Rolling Bearings — Identification Code — Supplemental Regulations
SH 0004 Solvent Oil for Rubber Industry
3 Terms and Definitions
For the purpose of this document, the terms and definitions given in GB/T 24610.1 and the following apply.
3.1
peak value of bearing vibration velocity
the maximum value for the bearing vibration velocity within a given time interval
Foreword II
1 Scope
2 Normative References
3 Terms and Definitions
4 Codes for Groups
5 Technical Requirements
6 Measurement Methods
7 Evaluation Methods
8 Inspection Rules
Annex A (Normative) Measurement Methods of Mandrel Radial and Axial Circular Runouts
Annex B (Normative) Measurement Methods for Foundation Vibration of Driving Device
1 Scope
This standard specifies the technical requirements, measurement methods, evaluation methods and inspection rules for the vibration (velocity) of deep groove ball bearings of diameter series 0, 2, 3 (hereinafter referred to as bearings) with the nominal external diameter greater than 10 mm to 200 mm and the boundary dimensions conforming to GB/T 276.
This standard is applicable to deep groove ball bearings. Group V specified in this standard is the basic requirement for vibration (velocity) of general bearing; Groups V1, V2, V3, V4 and VF3, VF4 are applicable to the bearings with higher vibration (velocity) requirements, and Groups VF3 and VF4 group are only applicable to the bearings with a nominal external diameter of more than 10 mm to 100 mm.
2 Normative References
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 276 Rolling Bearings — Deep Groove Ball Bearings — Boundary Dimensions
GB 443 Lubricating Oils for Total Loss Systems L-AN
GB/T 2828.1 Sampling Procedures for Inspection by Attributes — Part 1: Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-lot Inspection
GB/T 24610.1 Rolling Bearings — Measuring Methods for Vibration — Part 1: Fundamentals
GB/T 24610.2 Rolling Bearings — Measuring Methods for Vibration — Part 2: Radial Ball Bearings with Cylindrical Bore and Outside Surface
JB/T 2974 Rolling Bearings — Identification Code — Supplemental Regulations
SH 0004 Solvent Oil for Rubber Industry
3 Terms and Definitions
For the purpose of this document, the terms and definitions given in GB/T 24610.1 and the following apply.
3.1
peak value of bearing vibration velocity
the maximum value for the bearing vibration velocity within a given time interval
Contents of GB/T 32325-2015
Foreword II
1 Scope
2 Normative References
3 Terms and Definitions
4 Codes for Groups
5 Technical Requirements
6 Measurement Methods
7 Evaluation Methods
8 Inspection Rules
Annex A (Normative) Measurement Methods of Mandrel Radial and Axial Circular Runouts
Annex B (Normative) Measurement Methods for Foundation Vibration of Driving Device