GB/T 48072-2026 Sodium ion cells and batteries used in electrical energy storage systems - Safety technical specification
1 Scope
This document specifies the safety requirements for sodium ion cells and batteries used in electrical energy storage systems, and describes the corresponding test methods.
This document is applicable to sodium ion cells and batteries used in electrical energy storage systems (hereinafter referred to as "cells" and "batteries"). The applications of electrical energy storage systems include but are not limited to:
a) Telecommunications;
b) Central emergency lighting and alarm systems;
c) Uninterruptible power supplies (UPS) and emergency power supplies;
d) Stationary engine starting;
e) Photovoltaic systems;
f) Home (residential) energy storage systems;
g) Large-capacity energy storage.
2 Normative references
The contents in the following documents constitute essential provisions of this document through normative references in the text. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 2423.4 Environmental testing for electric and electronic products - Part 2: Test method - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
GB/T 2423.18 Environmental testing - Part 2: Test methods - Test Kb:Salt mist, cyclic (sodium chloride solution)
GB 4943.1 Audio/video, information and communication technology equipment - Part 1: Safety requirements
GB/T 5169.16 Fire hazard testing for electric and electronic products - Part 16: Test flames - 50 W horizontal and vertical flame test methods
GB/T 5169.21 Fire hazard testing for electric and electronic products - Part 21: Abnormal heat - Ball pressure test method
GB/T 17626.2 Electromagnetic compatibility - Testing and measurement techniques - Electrostatic discharge immunity test
GB/T 45565 Coding regulations of lithium ion batteries
SJ/T 12033 Sodium ion batteries - Terminology and vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in SJ/T 12033 and listed in the following apply.
3.1
sodium ion cell
device that converts chemical energy into electrical energy and vice versa by the back-and-forth migration of sodium ions between the positive electrode and negative electrode
Note 1 to entry: It generally includes electrodes, separator, electrolyte, container, and terminals, and is the minimum unit for energy conversion.
Note 2 to entry: It is hereinafter referred to as "cell".
3.2
large sodium ion cell
sodium ion cell with a total mass exceeding 500 g
Note to entry: It is hereinafter referred to as "large cell".
3.3
cell block
group of cells connected together in parallel configuration with or without protective devices [e.g., fuse or positive temperature coefficient (PTC) thermistor] and monitoring circuitry
Note to entry: It is not ready for use in equipment because it is not yet fitted with its final housing, terminal arrangement and electronic control device.
[SOURCE: IEC 63056:2020, 3.8]
3.4
module
group of cells connected together in a series and/or parallel configuration with or without protective devices [e.g., fuse or positive temperature coefficient (PTC) thermistor] and monitoring circuitry
[SOURCE: IEC 63056:2020, 3.9, modified]
3.5
battery pack
energy storage device which comprises one or more cells or modules electrically connected
Note 1 to entry: A battery pack includes the monitoring circuitry that provides information (such as cell voltage) to the battery system.
Note 2 to entry: A battery pack may incorporate a protective housing provided with terminals or other interconnection arrangement.
[SOURCE: IEC 63056:2020, 3.10, modified]
3.6
battery system
battery
system which comprises one or more cells, modules or battery packs
Note 1 to entry: It is equipped with a battery management system that acts in the event of overcharge, overcurrent, overdischarge, overtemperature, etc.
Note 2 to entry: Overdischarge cutoff is not mandatory if there is an agreement between the cell manufacturer and the user.
Note 3 to entry: The battery system may have cooling or heating devices, and some may even have charge-discharge modules and inverter modules.
Note 4 to entry: More than one battery system may constitute a larger battery system.
[SOURCE: IEC 63056:2020, 3.11, modified]
3.7
large sodium ion battery
sodium ion battery with a total mass exceeding 12 kg
Note to entry: It is hereinafter referred to as "large battery".
3.8
battery management system; BMS
set of protection functions associated with a battery to prevent overcharge, overcurrent, overtemperature, under-temperature and, if applicable, overdischarge and which monitors and/or manages its state, calculates secondary data, reports the data and/or controls its environment to influence the battery’s safety, performance and/or service life
Contents
Foreword III
1 Scope
2 Normative references
3 Terms and definitions
4 Test conditions
4.1 Applicability of tests
4.2 Environmental conditions for tests
4.3 Tolerances for parameter measurement
4.4 Temperature measurement method
4.5 Charging and discharging procedures for tests
4.6 Type test
5 General safety requirements
5.1 General safety considerations
5.2 Safe operating parameters
5.3 Marking and warning instructions
5.4 Safety-critical components
6 Electrical safety requirements and test methods for cells
6.1 External short circuit at high temperature
6.2 Overcharge
6.3 Forced discharge
7 Environmental safety requirements and test methods
7.1 Low air pressure
7.2 Temperature cycling
7.3 Vibration
7.4 Acceleration impact
7.5 Drop-weight impact
7.6 Crush
7.7 Nail penetration
7.8 Thermal abuse
7.9 Drop
7.10 Salt mist
7.11 Cyclic damp heat
8 Electrical safety requirements and test methods for battery system
8.1 Requirements for battery management unit / battery management system
8.2 Test sample
8.3 Overvoltage charging control
8.4 Overcurrent charging control
8.5 Undervoltage discharging control
8.6 Overtemperature control
9 Other requirements
9.1 Abnormal heat resistance
9.2 Casing materials for transportable battery systems used for installation or maintenance
9.3 Electrical insulation performance during transport and installation
9.4 Short circuit protection during transport and installation
9.5 Reverse connection protection
9.6 Dielectric strength of battery system
9.7 Pressure resistance of liquid cooling
9.8 Thermal runaway of cells and thermal propagation of battery systems
9.9 Packaging and transport
Annex A (normative) Test sequence
Annex B (normative) Procedure of thermal runaway test for cells
B.1 Test object
B.2 Test method
Annex C (informative) Procedure of propagation test by laser radiation
C.1 General
C.2 Test conditions
Annex D (informative) Procedure of propagation test using methods other than lasers
D.1 General
D.2 Test conditions
D.3 Methods for initiating thermal runaway
D.4 Example of procedure of propagation test by internal heating
Annex E (informative) Packaging and transport
Bibliography
GB/T 48072-2026 Sodium ion cells and batteries used in electrical energy storage systems - Safety technical specification
1 Scope
This document specifies the safety requirements for sodium ion cells and batteries used in electrical energy storage systems, and describes the corresponding test methods.
This document is applicable to sodium ion cells and batteries used in electrical energy storage systems (hereinafter referred to as "cells" and "batteries"). The applications of electrical energy storage systems include but are not limited to:
a) Telecommunications;
b) Central emergency lighting and alarm systems;
c) Uninterruptible power supplies (UPS) and emergency power supplies;
d) Stationary engine starting;
e) Photovoltaic systems;
f) Home (residential) energy storage systems;
g) Large-capacity energy storage.
2 Normative references
The contents in the following documents constitute essential provisions of this document through normative references in the text. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 2423.4 Environmental testing for electric and electronic products - Part 2: Test method - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
GB/T 2423.18 Environmental testing - Part 2: Test methods - Test Kb:Salt mist, cyclic (sodium chloride solution)
GB 4943.1 Audio/video, information and communication technology equipment - Part 1: Safety requirements
GB/T 5169.16 Fire hazard testing for electric and electronic products - Part 16: Test flames - 50 W horizontal and vertical flame test methods
GB/T 5169.21 Fire hazard testing for electric and electronic products - Part 21: Abnormal heat - Ball pressure test method
GB/T 17626.2 Electromagnetic compatibility - Testing and measurement techniques - Electrostatic discharge immunity test
GB/T 45565 Coding regulations of lithium ion batteries
SJ/T 12033 Sodium ion batteries - Terminology and vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in SJ/T 12033 and listed in the following apply.
3.1
sodium ion cell
device that converts chemical energy into electrical energy and vice versa by the back-and-forth migration of sodium ions between the positive electrode and negative electrode
Note 1 to entry: It generally includes electrodes, separator, electrolyte, container, and terminals, and is the minimum unit for energy conversion.
Note 2 to entry: It is hereinafter referred to as "cell".
3.2
large sodium ion cell
sodium ion cell with a total mass exceeding 500 g
Note to entry: It is hereinafter referred to as "large cell".
3.3
cell block
group of cells connected together in parallel configuration with or without protective devices [e.g., fuse or positive temperature coefficient (PTC) thermistor] and monitoring circuitry
Note to entry: It is not ready for use in equipment because it is not yet fitted with its final housing, terminal arrangement and electronic control device.
[SOURCE: IEC 63056:2020, 3.8]
3.4
module
group of cells connected together in a series and/or parallel configuration with or without protective devices [e.g., fuse or positive temperature coefficient (PTC) thermistor] and monitoring circuitry
[SOURCE: IEC 63056:2020, 3.9, modified]
3.5
battery pack
energy storage device which comprises one or more cells or modules electrically connected
Note 1 to entry: A battery pack includes the monitoring circuitry that provides information (such as cell voltage) to the battery system.
Note 2 to entry: A battery pack may incorporate a protective housing provided with terminals or other interconnection arrangement.
[SOURCE: IEC 63056:2020, 3.10, modified]
3.6
battery system
battery
system which comprises one or more cells, modules or battery packs
Note 1 to entry: It is equipped with a battery management system that acts in the event of overcharge, overcurrent, overdischarge, overtemperature, etc.
Note 2 to entry: Overdischarge cutoff is not mandatory if there is an agreement between the cell manufacturer and the user.
Note 3 to entry: The battery system may have cooling or heating devices, and some may even have charge-discharge modules and inverter modules.
Note 4 to entry: More than one battery system may constitute a larger battery system.
[SOURCE: IEC 63056:2020, 3.11, modified]
3.7
large sodium ion battery
sodium ion battery with a total mass exceeding 12 kg
Note to entry: It is hereinafter referred to as "large battery".
3.8
battery management system; BMS
set of protection functions associated with a battery to prevent overcharge, overcurrent, overtemperature, under-temperature and, if applicable, overdischarge and which monitors and/or manages its state, calculates secondary data, reports the data and/or controls its environment to influence the battery’s safety, performance and/or service life
Contents of GB/T 48072-2026
Contents
Foreword III
1 Scope
2 Normative references
3 Terms and definitions
4 Test conditions
4.1 Applicability of tests
4.2 Environmental conditions for tests
4.3 Tolerances for parameter measurement
4.4 Temperature measurement method
4.5 Charging and discharging procedures for tests
4.6 Type test
5 General safety requirements
5.1 General safety considerations
5.2 Safe operating parameters
5.3 Marking and warning instructions
5.4 Safety-critical components
6 Electrical safety requirements and test methods for cells
6.1 External short circuit at high temperature
6.2 Overcharge
6.3 Forced discharge
7 Environmental safety requirements and test methods
7.1 Low air pressure
7.2 Temperature cycling
7.3 Vibration
7.4 Acceleration impact
7.5 Drop-weight impact
7.6 Crush
7.7 Nail penetration
7.8 Thermal abuse
7.9 Drop
7.10 Salt mist
7.11 Cyclic damp heat
8 Electrical safety requirements and test methods for battery system
8.1 Requirements for battery management unit / battery management system
8.2 Test sample
8.3 Overvoltage charging control
8.4 Overcurrent charging control
8.5 Undervoltage discharging control
8.6 Overtemperature control
9 Other requirements
9.1 Abnormal heat resistance
9.2 Casing materials for transportable battery systems used for installation or maintenance
9.3 Electrical insulation performance during transport and installation
9.4 Short circuit protection during transport and installation
9.5 Reverse connection protection
9.6 Dielectric strength of battery system
9.7 Pressure resistance of liquid cooling
9.8 Thermal runaway of cells and thermal propagation of battery systems
9.9 Packaging and transport
Annex A (normative) Test sequence
Annex B (normative) Procedure of thermal runaway test for cells
B.1 Test object
B.2 Test method
Annex C (informative) Procedure of propagation test by laser radiation
C.1 General
C.2 Test conditions
Annex D (informative) Procedure of propagation test using methods other than lasers
D.1 General
D.2 Test conditions
D.3 Methods for initiating thermal runaway
D.4 Example of procedure of propagation test by internal heating
Annex E (informative) Packaging and transport
Bibliography