This part of GB/T 7095 specifies the general requirements of enamelled rectangular copper winding wires.
The range of nominal conductor dimensions is given in the relevant specification sheet.
When reference is made to a winding wire according to a standard of the GB/T 7095 series mentioned under clause 2, the following information is given in the description:
— Reference to GB and/or IEC specification;
— Nominal conductor dimensions in millimetres (width × thickness);
— Grade of thickness of the insulation.
Example: GB/T 7095.3-2008, 4.00 × 1.00 Grade 1; or IEC 60317-16 – 4.00 × 1.00 Grade 1.
Foreword II
1 Scope 1
2 Normative References 1
3 Definitions, General Notes on Tests and Appearance 2
4 Dimensions 3
5 Electrical Resistance 6
6 Elongation 7
7 Springiness 7
8 Flexibility and Adherence 7
9 Heat Shock 7
10 Cut-through 7
11 Resistance to Abrasion 7
12 Resistance to Solvents 7
13 Breakdown Voltage 8
14 Continuity of Insulation 8
15 Temperature Index 8
16 Resistance to Refrigerants 8
17 Solderability 8
18 Heat or Solvent Bonding 8
19 Dielectric Dissipation Factor 8
20 Resistance to Transformer Oil 9
21 Loss of Mass 9
23 Pin-hole Test 9
30 Packaging 9
Appendix A (Informative) Nominal Cross-sectional Areas for Preferred and Intermediate Sizes 10
Appendix B (Informative) Special Tolerances 20
Appendix E (Informative) High Temperature Failure Test 21
Appendix F (Informative) Type and Comparison Table of Enamelled Rectangular Copper Winding Wires 22
Appendix G (Informative) Test Item Categories 23
This part of GB/T 7095 specifies the general requirements of enamelled rectangular copper winding wires.
The range of nominal conductor dimensions is given in the relevant specification sheet.
When reference is made to a winding wire according to a standard of the GB/T 7095 series mentioned under clause 2, the following information is given in the description:
— Reference to GB and/or IEC specification;
— Nominal conductor dimensions in millimetres (width × thickness);
— Grade of thickness of the insulation.
Example: GB/T 7095.3-2008, 4.00 × 1.00 Grade 1; or IEC 60317-16 – 4.00 × 1.00 Grade 1.
Contents of GB/T 7095.1-2008
Foreword II
1 Scope 1
2 Normative References 1
3 Definitions, General Notes on Tests and Appearance 2
4 Dimensions 3
5 Electrical Resistance 6
6 Elongation 7
7 Springiness 7
8 Flexibility and Adherence 7
9 Heat Shock 7
10 Cut-through 7
11 Resistance to Abrasion 7
12 Resistance to Solvents 7
13 Breakdown Voltage 8
14 Continuity of Insulation 8
15 Temperature Index 8
16 Resistance to Refrigerants 8
17 Solderability 8
18 Heat or Solvent Bonding 8
19 Dielectric Dissipation Factor 8
20 Resistance to Transformer Oil 9
21 Loss of Mass 9
23 Pin-hole Test 9
30 Packaging 9
Appendix A (Informative) Nominal Cross-sectional Areas for Preferred and Intermediate Sizes 10
Appendix B (Informative) Special Tolerances 20
Appendix E (Informative) High Temperature Failure Test 21
Appendix F (Informative) Type and Comparison Table of Enamelled Rectangular Copper Winding Wires 22
Appendix G (Informative) Test Item Categories 23