JB/T 2379-2016 Metallic tube type electroheating elements
1 Scope
This standard specifies the terms and definitions, product classification, technical requirements, test methods, inspection rules, as well as marking, packaging, transport and storage, ordering and supply of metallic tube type electroheating elements (hereinafter referred to as "elements").
This standard is applicable to metallic tube type electroheating elements with metallic tubes as cases.
This standard is not applicable to tube type electroheating elements for daily and similar uses.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB 5959.1-2005 Safety in electroheat installations - Part 1: General requirements
GB/T 10066.1-2004 Test methods for electroheat installations - Part 1: General
GB/T 10067.1-2005 Basic specifications for electroheat installations - Part 1: General
3 Terms and definitions
For the purposes of this document, the terms and definitions given in GB/T 2900.23-2008 and GB/T 10066.1-2004 as well as the following apply.
3.1
metallic tube type electroheating elements
electroheating element with a metallic tube as the case, an alloy heating wire as the heater, leads protruding from one end or both ends, and a dense magnesium oxide powder insulating medium filled in the metallic tube to fix the heating element
3.2
lead
conductive metallic part connected with the heater to connect the element with the power supply or another element
3.3
stretching length
L
sum of the length of the straight and curved portions of the metallic tube on the element drawing, in millimeters (mm)
Foreword I 1 Scope 2 Normative references 3 Terms and definitions 4 Product classification 4.1 Types and specifications 4.2 Designation 4.3 Main parameters 5 Technical requirements 5.1 Design requirements 5.2 Manufacturing requirements 5.3 Performance requirements 6 Test methods 6.1 General requirements 6.2 Lead tension test 6.3 Sealing test 6.4 X-ray inspection 6.5 Measurement of temperature rise time 6.6 Measurement of rated power 6.7 Measurement of leakage current 6.8 Measurement of insulation resistance 6.9 Dielectric strength test 6.10 On/off test 6.11 Overload test 6.12 Heat resistance test 7 Inspection rules 7.1 Acceptance type 7.2 End-of-manufacturing inspection 7.3 Type inspection 7.4 Others 8 Marking, packaging, transport and storage 9 Ordering and supply 9.1 Ordering documents 9.2 Special requirements 9.3 Basis for supply 9.4 Technical assurance
JB/T 2379-2016 Metallic tube type electroheating elements
1 Scope
This standard specifies the terms and definitions, product classification, technical requirements, test methods, inspection rules, as well as marking, packaging, transport and storage, ordering and supply of metallic tube type electroheating elements (hereinafter referred to as "elements").
This standard is applicable to metallic tube type electroheating elements with metallic tubes as cases.
This standard is not applicable to tube type electroheating elements for daily and similar uses.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 2900.23-2008 Electrotechnical terminology - Industrial electroheat
GB 5959.1-2005 Safety in electroheat installations - Part 1: General requirements
GB/T 10066.1-2004 Test methods for electroheat installations - Part 1: General
GB/T 10067.1-2005 Basic specifications for electroheat installations - Part 1: General
3 Terms and definitions
For the purposes of this document, the terms and definitions given in GB/T 2900.23-2008 and GB/T 10066.1-2004 as well as the following apply.
3.1
metallic tube type electroheating elements
electroheating element with a metallic tube as the case, an alloy heating wire as the heater, leads protruding from one end or both ends, and a dense magnesium oxide powder insulating medium filled in the metallic tube to fix the heating element
3.2
lead
conductive metallic part connected with the heater to connect the element with the power supply or another element
3.3
stretching length
L
sum of the length of the straight and curved portions of the metallic tube on the element drawing, in millimeters (mm)
Contents of JB/T 2379-2016
Foreword I
1 Scope
2 Normative references
3 Terms and definitions
4 Product classification
4.1 Types and specifications
4.2 Designation
4.3 Main parameters
5 Technical requirements
5.1 Design requirements
5.2 Manufacturing requirements
5.3 Performance requirements
6 Test methods
6.1 General requirements
6.2 Lead tension test
6.3 Sealing test
6.4 X-ray inspection
6.5 Measurement of temperature rise time
6.6 Measurement of rated power
6.7 Measurement of leakage current
6.8 Measurement of insulation resistance
6.9 Dielectric strength test
6.10 On/off test
6.11 Overload test
6.12 Heat resistance test
7 Inspection rules
7.1 Acceptance type
7.2 End-of-manufacturing inspection
7.3 Type inspection
7.4 Others
8 Marking, packaging, transport and storage
9 Ordering and supply
9.1 Ordering documents
9.2 Special requirements
9.3 Basis for supply
9.4 Technical assurance
