1.1 This code presents the technological process and construction method in the construction of vertical cylindrical low-temperature storage tank and specifies the process control, quality inspection, and test requirement for the precasting, assembling and welding.
1.2 This code is applicable to the precasting, assembling, welding, inspection, test and acceptance and inspection of the vertical cylindrical low-temperature storage tank (hereinafter referred to as low-temperature storage tank), its nominal capacity is greater than or equal to 10000m3 and its design temperature is neither higher than -45℃ or nor less than -168℃. Those low-temperature storage tanks with nominal capacity being less than 10000m3 may be used by referring to this.
1.3 This code is applicable to the low-temperature storage tank storing such mediums as liquefied petroleum gas, propylene, ethylene, and natural gas. And those low-temperature storage tanks storing other mediums may be used by referring to this.
1.4 This code is applicable to the construction of low-temperature storage tank made of low alloy steel. And the stainless steel low-temperature storage tank may be used by referring to this.
1.5 This code is applicable to the steel single-layer low-temperature storage tank, steel double-layer low-temperature storage tank, and steel part of the double-layer low-temperature storage tank whose outer tank is of reinforced concrete structure. Please see appendix A for its typical structure.
1 Scope
2 Normative references
3 General requirements
4 Preparation of construction
5 Materials
6 Construction process
7 Precasting processing
7.1 General requirements
7.2 Soleplate precasting
7.3 Wallboard precasting
7.4 Vault precasting
7.5 Precasting of inner suspending roof
7.6 Precasting of other elements
7.7 Delivery inspection
8 Recheck of the foundation and outer reinforced concrete tank
8.1 Recheck of foundation
8.2 Recheck of outer reinforced concrete tank
9 Assembly of tank bottom
9.1 General requirements
9.2 Assembly of overlapped tank soleplates
9.3 Assembly of butt joint soleplate in tank
9.4 Assembly of inner double-layer low-temperature storage tank bottom
10 Assembly of tank shell
10.1 General requirements
10.2 Assembly of tank shell
11 Assembly of tank deck
11.1 Central support method
11.2 Air-lifting method
12 Installation of appurtenance
12.1 Installation of pipe at open pore of tank shell
12.2 Installation of other appurtenances
13 Welding
13.1 General requirements
13.2 Management of welding materials
13.3 Welding requirements
13.4 Welding sequences and methods
13.5 Repairing
14 Cold insulation
14.1 General requirements
14.2 Cold insulation of tank bottom
14.3 Cold insulation of tank shell
14.4 Cold insulation of pipelines in tank
14.5 Cold insulation of inner suspending roof
15 Inspection and test
15.1 Inspection of weld appearance
15.2 Nondestructive test and leakage test of weld
15.3 Geometric shape and dimension inspection of tank shell
15.4 Test of tank body
16 Engineering acceptance
Appendix A (Informative) Several Typical Structures of Low-temperature Storage Tank
Appendix B (Informative) Construction Process Flow
SH/T 3537-2002, SH 3537-2002, SHT 3537-2002, SH/T3537-2002, SH/T 3537, SH/T3537, SH3537-2002, SH 3537, SH3537, SHT3537-2002, SHT 3537, SHT3537
Introduction of SH/T 3537-2002
1.1 This code presents the technological process and construction method in the construction of vertical cylindrical low-temperature storage tank and specifies the process control, quality inspection, and test requirement for the precasting, assembling and welding.
1.2 This code is applicable to the precasting, assembling, welding, inspection, test and acceptance and inspection of the vertical cylindrical low-temperature storage tank (hereinafter referred to as low-temperature storage tank), its nominal capacity is greater than or equal to 10000m3 and its design temperature is neither higher than -45℃ or nor less than -168℃. Those low-temperature storage tanks with nominal capacity being less than 10000m3 may be used by referring to this.
1.3 This code is applicable to the low-temperature storage tank storing such mediums as liquefied petroleum gas, propylene, ethylene, and natural gas. And those low-temperature storage tanks storing other mediums may be used by referring to this.
1.4 This code is applicable to the construction of low-temperature storage tank made of low alloy steel. And the stainless steel low-temperature storage tank may be used by referring to this.
1.5 This code is applicable to the steel single-layer low-temperature storage tank, steel double-layer low-temperature storage tank, and steel part of the double-layer low-temperature storage tank whose outer tank is of reinforced concrete structure. Please see appendix A for its typical structure.
Contents of SH/T 3537-2002
1 Scope
2 Normative references
3 General requirements
4 Preparation of construction
5 Materials
6 Construction process
7 Precasting processing
7.1 General requirements
7.2 Soleplate precasting
7.3 Wallboard precasting
7.4 Vault precasting
7.5 Precasting of inner suspending roof
7.6 Precasting of other elements
7.7 Delivery inspection
8 Recheck of the foundation and outer reinforced concrete tank
8.1 Recheck of foundation
8.2 Recheck of outer reinforced concrete tank
9 Assembly of tank bottom
9.1 General requirements
9.2 Assembly of overlapped tank soleplates
9.3 Assembly of butt joint soleplate in tank
9.4 Assembly of inner double-layer low-temperature storage tank bottom
10 Assembly of tank shell
10.1 General requirements
10.2 Assembly of tank shell
11 Assembly of tank deck
11.1 Central support method
11.2 Air-lifting method
12 Installation of appurtenance
12.1 Installation of pipe at open pore of tank shell
12.2 Installation of other appurtenances
13 Welding
13.1 General requirements
13.2 Management of welding materials
13.3 Welding requirements
13.4 Welding sequences and methods
13.5 Repairing
14 Cold insulation
14.1 General requirements
14.2 Cold insulation of tank bottom
14.3 Cold insulation of tank shell
14.4 Cold insulation of pipelines in tank
14.5 Cold insulation of inner suspending roof
15 Inspection and test
15.1 Inspection of weld appearance
15.2 Nondestructive test and leakage test of weld
15.3 Geometric shape and dimension inspection of tank shell
15.4 Test of tank body
16 Engineering acceptance
Appendix A (Informative) Several Typical Structures of Low-temperature Storage Tank
Appendix B (Informative) Construction Process Flow