Code of China Chinese Classification Professional Classification ICS Classification Latest Value-added Services

LoginRegister

Title Standard No. Implemented On
Die casting dies—Components—Part 13: Ejector plate washersGB/T 4678.13-20182019-4-1
Die casting dies—Components—Part 12:Return pinsGB/T 4678.12-20182019-4-1
Cold chamber die casting machinesGB/T 21269-20182018-12-1
Diecasting dies - Components - Part 11: Ejector pinGB/T 4678.11-20172018-4-1
Diecasting dies--Components--Part 2: Round insertsGB/T 4678.2-20172018-4-1
Diecasting dies--Components--Part 19: Locating elementGB/T 4678.19-20172018-4-1
Diecasting dies--Components--SpecificationsGB/T 4679-20172018-4-1
Diecasting dies - Components - Part 9: Ejector guide pillarGB/T 4678.9-20172018-4-1
Diecasting dies - Components - Part 8: Ejector plateGB/T 4678.8-20172018-4-1
Diecasting dies--Components--Part 6: Headed guide bushGB/T 4678.6-20172018-4-1
Diecasting dies - Components - Part 10: Ejector guide bushGB/T 4678.10-20172018-4-1
Diecasting dies--Components--Part 4: Square guide pillarsGB/T 4678.4-20172018-4-1
Diecasting dies--Components--Part 7: Straight guide bushGB/T 4678.7-20172018-4-1
Diecasting dies--Components--Part 3: Rectangular insertsGB/T 4678.3-20172018-4-1
Foundry machinery - Noise measurement method of sound power levelsGB/T 34388-20172018-4-1
Diecasting dies--Components--Part 5: Round guide pillarGB/T 4678.5-20172018-4-1
Tools for moulding-Tool specification sheet for diecasting diesGB/T 32663-20162016-11-1
Tools for moulding-Tool specification sheet for injection mouldsGB/T 32664-20162016-11-1
Blast wheelGB/T 32567-20162016-9-1
Coldbox venting plugT/CFA 020302-1-20162016-6-1
Blowtube sealing sleeve of the tolling for castingT/CFA 020302-2-20162016-6-1
External combustion hot blast cupolaGB/T 31553-20152016-1-1
Manipulator for foundryGB/T 31555-20152016-1-1
Foundry machinery―Determination of cleanlinessGB/T 31562-20152016-1-1
Used green sand reclamation equipment―Technical requirementsGB/T 31561-20152016-1-1
Sodium silicate-bonded sand reclamation equipment―Technical requirementsGB/T 31551-20152016-1-1
Foundry machinery―Model formulating meansGB/T 31552-20152016-1-1
Fine blanking dies - SpecificationsGB/T 30218-20132014-10-1
Green sand mixer - Safety requirementsGB 28759-20122013-10-1
Low pressure die casting machine—Technical requirementsGB/T 28688-20122013-1-1
Numerical control die casting machinesGB/T 28687-20122013-1-1
Efficient rotator mixer—Technical requirementsGB/T 28689-20122013-1-1
Resin-bonded sand reclamation equipment—Technical requirementsGB/T 28690-20122013-1-1
Molten steel ladle - Safety requirementsGB 25683-20102012-1-1
Molding machine - Safety requirementsGB 25491-20102011-10-1
Shakeout - Safety requirementsGB 25492-20102011-10-1
Water-cooled tuyeres- Part 1:Types and basic parametersJB/T 11161.1-20112011-8-1
Slag conveyors for cupolas - Technical requirementsJB/T 11159-20112011-8-1
Electromagnetic drum-Technical requirementsJB/T 6101-20112011-8-1
Hanger blasting cleaning machine - Technical requirementsJB/T 11164-20112011-8-1
Slag extractors- Part 2:Technical requirementsJB/T 11158.2-20112011-8-1
Electromagnetic pulley-Technical requirementsJB/T 6100-20112011-8-1
Cupola charging machines - Part 2:Technical requirementsJB/T 8350.2-20112011-8-1
Hydro-deduster for cupola use - Technical requirementsJB/T 11163-20112011-8-1
Roller conveyor shot blasting machine -Part 1:ParametersJB/T 9984.1-20112011-8-1
Cupola forehearth - Part 2:Technical requirementsJB/T 11043.2-20112011-8-1
Two-way belt conveyer for mix and feed system of cupolaJB/T 11180-20112011-8-1
Skip hoist-Part 1:Basic parametersJB/T 11165.1-20112011-8-1
Rising and falling ladle - Part 2: Technical requirementsJB/T 11046.2-20112011-8-1
Ladle drier-Technical requirementsJB/T 6577-20112011-8-1
Overhead hanger continuous system shot blasting machine -Technical requirementsJB/T 9979-20112011-8-1
Overhead hanger stepping shot blasting machine -Technical requirementsJB/T 8351-20112011-8-1
Dense muscle-type heat exchanger -Part 1:Basic parametersJB/T 11183.1-20112011-8-1
Directional force excitersJB/T 11166-20112011-8-1
Iron charge skip bucket - Part 2:Technical requirementsJB/T 11184.2-20112011-8-1
Top spraying dust collector of cupola-Technical requirementsJB/T 11179-20112011-8-1
Continuous mould conveyor -Technical requirementsJB/T 8607-20112011-8-1
Slag extractors- Part 1:Types and basic parametersJB/T 11158.1-20112011-8-1
Cupola charging machines - Part 1:Types and basic parametersJB/T 8350.1-20112011-8-1
Cupola rotating chute - Technical requirementsJB/T 11162-20112011-8-1
Water-cooled tuyeres- Part 2:Technical requirementsJB/T 11161.2-20112011-8-1
Transitional charging skipJB/T 11182-20112011-8-1
Skip hoist-Part 2:Technical requirementsJB/T 11165.2-20112011-8-1
Heat exchangers- Part 1:Types and basic parametersJB/T 11160.1-20112011-8-1
Heat exchangers- Part 2:Technical requirementsJB/T 11160.2-20112011-8-1
Top spraying dust collector of cupola-Technical requirementsJB/T 11181-20112011-8-1
Double-disk blast whell -Part 2:Technical requirementJB/T 3713.2-20112011-8-1
Magnetic-drum separator-Technical requirementsJB/T 6099-20112011-8-1
Roller conveyor shot blasting machine -Part 2:Technical requirementsJB/T 9984.2-20112011-8-1
Vibratory stress relief technology - Parameter selection and effect evaluation methodsGB/T 25712-20102011-7-1
Sphere nodular cast pipe mold finish machining projectGB/T 25715-20102011-7-1
Hot chamber die casting machines for magnesium alloysGB/T 25717-20102011-7-1
Molten iron ladle - Part 2: Types and basic parametersGB/T 25714.1-20102011-7-1
Cold chamber die casting machines for magnesium alloysGB/T 25716-20102011-7-1
Molten iron ladle - Part 2: Technical requirementsGB/T 25714.2-20102011-7-1
Foundry machinery - General technical requirementsGB/T 25711-20102011-7-1
Foundry machinery—TerminologyGB/T 25370-20102011-3-1
Specification of moulds for vacuum thermoformingGB/T 25143-20102011-3-1
Foundry machinery—Measurement method of sound pressure levelGB/T 25371-20102011-3-1
Shot(air)blast equipment - Safety requirementsGB 24390-20092010-7-1
Side heated hot blast cupla - Technical requirementsJB/T 11045-20102010-7-1
Single - Track hoist for cupola - Technical requirementsJB/T 11042-20102010-7-1
Desulphation ladle - Part 1: Basic parameterJB/T 11047.1-20102010-7-1
Cupola forehearth - Part 1: Types and basic parametersJB/T 11043.1-20102010-7-1
Single - Track hoist for cupola - Technical requirementsJB/T 11041-20102010-7-1
Work car shot blastingmachine-Technical requirementsJB/T 8495-20102010-7-1
Rising and falling ladle-Part 1:Types and basic parametersJB/T 11046.1-20102010-7-1
Multi-table shot blasting machine-Technical requirementJB/T 11044-20102010-7-1
Low pressure die casting machine—Safety requirementsGB 24391-20092010-7-1
Molten steel ladle—Part 2:Technical requirementsGB/T 23583.2-20092010-1-1
Sliding guide steel-plate punch holders of stamping dies—Part 2:Diagonal-pillar punch holdersGB/T 23566.2-20092010-1-1
Abrasive blasting equipment - General technical requirementsGB/T 23576-20092010-1-1
Ball-bearing guide steel-plate punch holders of stamping dies - Part 2: Diagonal-pillar punch holdersGB/T 23564.2-20092010-1-1
Steel-plate die holders of stamping dies—Part 3:Center-pillar die holdersGB/T 23562.3-20092010-1-1
Sliding guide steel-plate punch holders of stamping dies - Part 1: Rear-pillar punch holdersGB/T 23566.1-20092010-1-1
Sliding guide steel-plate die sets of stamping dies—Part 2:Diagonal-pillar die setsGB/T 23565.2-20092010-1-1
Sliding guide steel-plate die sets of stamping dies—Part 1:Rear-pillar die setsGB/T 23565.1-20092010-1-1
Ball-bearing guide steel-plate punch holders of stamping dies - Part 4: Four-pillar punch holdersGB/T 23564.4-20092010-1-1
Ball-bearing guide steel-plate die sets of stamping dies - Part 2: Diagonal-pillar die setsGB/T 23563.2-20092010-1-1
Steel-plate die holders of stamping dies—Part 4:Four-pillar die holdersGB/T 23562.4-20092010-1-1
Molten steel ladle - Part 1: Types and basic parametersGB/T 23583.1-20092010-1-1
Ball-bearing guide steel-plate die sets of stamping dies - Part 4: Four-pillar die setsGB/T 23563.4-20092010-1-1
Ball-bearing guide steel-plate die sets of stamping dies - Part 3: Center-pillar die setsGB/T 23563.3-20092010-1-1
Ball-bearing guide steel-plate punch holders of stamping dies—Part 1:Rear-pillar punch holdersGB/T 23564.1-20092010-1-1
Sliding guide steel-plate punch holders of stamping dies - Part 3: Center-pillar punch holdersGB/T 23566.3-20092010-1-1
Steel-plate die holders of stamping dies—Part 1:Rear-pillar die holdersGB/T 23562.1-20092010-1-1
Sliding guide steel-plate die sets of stamping dies - Part 4: Four-pillar die setsGB/T 23565.4-20092010-1-1
Sliding guide steel-plate punch holders of stamping dies - Part 4: Four-pillar punch holdersGB/T 23566.4-20092010-1-1
Ball-bearing guide steel-plate die sets of stamping dies - Part 1: Rear-pillar die setsGB/T 23563.1-20092010-1-1
Steel-plate die holders of stamping dies—Part 2:Diagonal-pillar die holdersGB/T 23562.2-20092010-1-1
Ball-bearing guide steel-plate punch holders of stamping dies - Part 3: Center-pillar punch holdersGB/T 23564.3-20092010-1-1
Sliding guide steel-plate die sets of stamping dies - Part 3: Center-pillar die setsGB/T 23565.3-20092010-1-1
Cupola - Part 2: Technical requirementsGB/T 22341.2-20082009-2-1
Cupola - Part 1: Types and basic parametersGB/T 22341.1-20082009-2-1
Barrel shot blasting machine—Technical requirementsJB/T 7460-20082008-11-1
Components of plastic profile extrusion tooling—Part 4:Round adaptersJB/T 8746.4-20082008-11-1
Components of plastic profile extrusion tooling—Part 5:tank platesJB/T 8746.5-20082008-11-1
Components of plastic profile extrusion tooling—Part 6:mould platesJB/T 8746.6-20082008-11-1
Motor-driven vibrating feeders with rectangular or Trapezoidal trough—Types and basic parametersJB/T 9981-20082008-11-1
Overhead hanger type shot blasting reclaiming blast chamber—Basic parametersJB/T 6332-20082008-11-1
Components of plastic profile extrusion tooling—Part 2:Round mould platesJB/T 8746.2-20082008-11-1
Mixer of clay-bonded sand—General technical requirementsJB/T 505-20082008-11-1
Overhead hanger type shot blasting reclaiming blast chamber—Basic parametersJB/T 6333-20082008-11-1
Electrical extra-infrared heating core oven—Technical requirementsJB/T 8377-20082008-11-1
Core shooter with removable shooterJB/T 8785-20082008-11-1
Cupola skip hoistJB/T 10911-20082008-11-1
Eddy-vibrating finishing machineJB/T 6574-20082008-11-1
Components of plastic profile extrusion tooling—Part 3:Rectangular adaptersJB/T 8746.3-20082008-11-1
Motor-driven vibrating feeders with rectangular or Trapezoidal trough—Types and basic parametersJB/T 9983-20082008-11-1
Indirect heated hot blast cupola—Technical requirementsJB/T 10913-20082008-11-1
Specifications for plastic profile extrusion toolingJB/T 8745-20082008-11-1
Components of plastic profile extrusion tooling—Part 1:Rectangular mould platesJB/T 8746.1-20082008-11-1
Shakeout—Test methods for reliabilityJB/T 10914-20082008-11-1
Sand drying barrel with three returns—Technical requirementsJB/T 5551-20082008-11-1
Vibrating hopper feeder—Technical requirementsJB/T 6572-20082008-11-1
Water cooled and lingingless stack cupolaJB/T 10912-20082008-11-1
Double disk blast wheel-Part 1:Basic parametersJB/T 3713.1-20082008-11-1
Guide unit for stamping dies - Part 4: Guide bushes for ball-bearingGB/T 2861.4-20082008-10-1
Guide unit for stamping dies - Part 7: Guide pillars with taper lead for sliding guideGB/T 2861.7-20082008-10-1
Sliding guide die sets for stamping diesGB/T 2851-20082008-10-1
Holders for sliding guide die sets for stamping dies - Part 1: Punch holders for die setsGB/T 2855.1-20082008-10-1
Guide unit for stamping dies - Part 10: WashersGB/T 2861.10-20082008-10-1
Guide unit for stamping dies - Part 5: CagesGB/T 2861.5-20082008-10-1
Guide unit for stamping dies - Part 9: BushingsGB/T 2861.9-20082008-10-1
Guide unit for stamping dies - Part 3: Guide bushes for sliding guideGB/T 2861.3-20082008-10-1
Guide unit for stamping dies - Part 6: Cylindrical helical compression springsGB/T 2861.6-20082008-10-1
Holders for sliding guide die sets for stamping dies - Part 2: Die holders for die setsGB/T 2855.2-20082008-10-1
Guide unit for stamping dies - Part 11: ClampersGB/T 2861.11-20082008-10-1
Guide unit for stamping dies - Part 8: Guide pillars with taper lead for ball-bearingGB/T 2861.8-20082008-10-1
Holders for ball-bearing die sets for stamping dies - Part 2: Die holders for die setsGB/T 2856.2-20082008-10-1
Cupola and cupola charging machine - Safety requirementsGB 21501-20082008-10-1
Ball-bearing die sets for stamping diesGB/T 2852-20082008-10-1
Guide unit for stamping dies - Part 1: Guide pillars for sliding guideGB/T 2861.1-20082008-10-1
Holders for ball-bearing die sets for stamping dies - Part 1: Punch holders for die setsGB/T 2856.1-20082008-10-1
Guide unit for stamping dies - Part 2: Guide pillars for ball-bearingGB/T 2861.2-20082008-10-1
Stock stopping and spring units of stamping dies-Part 6:Stop sets with torsional springJB/T 7649.6-20082008-7-1
Stamping die plates-Part 1:Rectangular die platesJB/T 7643.1-20082008-7-1
Single punch plates of stamping dies-Part8:Bolster plates for ball-locked side-fixed single punchesJB/T 7645.2-20082008-7-1
Single punch plates of stamping dies-Part7:Retaining plates for ball-locked side-fixed single punchesJB/T 7644.7-20082008-7-1
Single punch plates of stamping dies-Part3:Retaining plates for side-fixed single punchesJB/T 7644.3-20082008-7-1
Specification of components for stamping die setsJB/T 8070-20082008-7-1
Single punch plates of stamping dies-Part8:Bolster plates for ball-locked side-fixed single punchesJB/T 7645.4-20082008-7-1
Pitch punch and stock guide units of stamping dies-Part 2:Stop blocks for pitch punches-Type AJB/T 7648.2-20082008-7-1
Stamping die shanks-Part 4:Slotted die shanksJB/T 7646.4-20082008-7-1
Stripping units of stamping dies-Part 1:Shouldered ejector pinsJB/T 7650.1-20082008-7-1
Specification of stamping die componentsJB/T 7653-20082008-7-1
Single punch plates of stamping dies-Part6:Bolster plates for ball-locked single punchesJB/T 7644.6-20082008-7-1
Pitch punch and stock guide units of stamping dies-Part 4:Stop blocks for pitch punches-Type CJB/T 7648.4-20082008-7-1
Pitch punch and stock guide units of stamping dies-Part 5:Stock guide railsJB/T 7648.5-20082008-7-1
Stamping dies-Round punches with cylindrical head and reduced shankJB/T 5826-20082008-7-1
Stock stopping and spring units of stamping dies-Part 4:Side-push leaf springsJB/T 7649.4-20082008-7-1
Stamping dies-Ball-locked round punchesJB/T 5829-20082008-7-1
Single punch plates of stamping dies-Part8:Bolster plates for ball-locked side-fixed single punchesJB/T 7645.5-20082008-7-1
Pilot pins of stamping dies-Part 1:Pilot pins-Type AJB/T 7647.1-20082008-7-1
Single punch plates of stamping dies-Part8:Bolster plates for ball-locked side-fixed single punchesJB/T 7645.1-20082008-7-1
Stripping units of stamping dies-Part 6:Hexagonal socket stripper boltsJB/T 7650.6-20082008-7-1
Stamping dies-Round punches with cylindrical head and straight shankJB/T 5825-20082008-7-1
Scrap cutters of stamping dies-Part 2:Square cutterJB/T 7651.2-20082008-7-1
Single punch plates of stamping dies-Part8:Bolster plates for ball-locked side-fixed single punchesJB/T 7645.7-20082008-7-1
Pitch punch and stock guide units of stamping dies-Part 7:Stock lifting pins-Type AJB/T 7648.7-20082008-7-1
Stock stopping and spring units of stamping dies-Part 1:Starting stop setsJB/T 7649.1-20082008-7-1
Single punch plates of stamping dies-Part8:Bolster plates for ball-locked side-fixed single punchesJB/T 7645.8-20082008-7-1
Stripping units of stamping dies-Part 8:Adjusting washersJB/T 7650.8-20082008-7-1
Stripping units of stamping dies-Part 4:Kicker platesJB/T 7650.4-20082008-7-1
Limiting and supporting units of stamping dies-Part 2:Limit pillarsJB/T 7652.2-20082008-7-1
Single punch plates of stamping dies-Part5:Retaining plates for ball-locked single punchesJB/T 7644.5-20082008-7-1
Single punch plates of stamping dies-Part8:Bolster plates for ball-locked side-fixed single punchesJB/T 7645.3-20082008-7-1
Stamping dies-Round punches with 60°conical head and straight shankJB/T 5827-20082008-7-1
Pilot pins of stamping dies-Part 3:Pilot pins-Type CJB/T 7647.3-20082008-7-1
Stamping die shanks-Part 6:Pushed-in movable die shanksJB/T 7646.6-20082008-7-1
Stock stopping and spring units of stamping dies-Part 8:Ball knockout stop setsJB/T 7649.8-20082008-7-1
Pitch punch and stock guide units of stamping dies-Part 8:Stock lifting pins-Type BJB/T 7648.8-20082008-7-1
Stripping units of stamping dies-Part 3:Kicker pinsJB/T 7650.3-20082008-7-1
Stripping units of stamping dies-Part 2:Screwed ejector pinsJB/T 7650.2-20082008-7-1
Stamping die shanks-Part 1:Press-fit die shanksJB/T 7646.1-20082008-7-1
Stamping die plates-Part 3:Rectangular bolster platesJB/T 7643.3-20082008-7-1
Stripping units of stamping dies-Part 5:Clyindrical head stripper boltsJB/T 7650.5-20082008-7-1
Stamping dies-Round diesJB/T 5830-20082008-7-1
Stock stopping and spring units of stamping dies-Part 10:Fixed stop pinsJB/T 7649.10-20082008-7-1
Stamping die plates-Part 6:Round bolster platesJB/T 7643.6-20082008-7-1
Accuracy test for stamping die setsJB/T 8071-20082008-7-1
Stamping die shanks-Part 5:Self-centering die shanksJB/T 7646.5-20082008-7-1
Stock stopping and spring units of stamping dies-Part 2:Mandrels for springsJB/T 7649.2-20082008-7-1
Stock stopping and spring units of stamping dies-Part 7:Tripper stop setsJB/T 7649.7-20082008-7-1
Single punch plates of stamping dies-Part1:Retaining plates for single punchesJB/T 7644.1-20082008-7-1
Stock stopping and spring units of stamping dies-Part 3:Spring-operated side push setsJB/T 7649.3-20082008-7-1
Pitch punch and stock guide units of stamping dies-Part 1:Pitch punchesJB/T 7648.1-20082008-7-1
Stock stopping and spring units of stamping dies-Part 9:Movable stop pinsJB/T 7649.9-20082008-7-1
Pitch punch and stock guide units of stamping dies-Part 3:Stop blocks for pitch punches-Type BJB/T 7648.3-20082008-7-1
Stamping die shanks-Part 2:Screwed die shanksJB/T 7646.2-20082008-7-1
Limiting and supporting units of stamping dies-Part 1:Supporting setsJB/T 7652.1-20082008-7-1
Single punch plates of stamping dies-Part2:Bolster plates for single punchesJB/T 7644.2-20082008-7-1
Single punch plates of stamping dies-Part8:Bolster plates for ball-locked side-fixed single punchesJB/T 7645.6-20082008-7-1
Stock stopping and spring units of stamping dies-Part 5:Stop sets with coil springJB/T 7649.5-20082008-7-1
Stamping die plates-Part 4:Round die platesJB/T 7643.4-20082008-7-1
Stamping die plates-Part 5:Round retaining platesJB/T 7643.5-20082008-7-1
Stamping die shanks-Part 3:Flanged die shanksJB/T 7646.3-20082008-7-1
Stripping units of stamping dies-Part 7:Width fixing setsJB/T 7650.7-20082008-7-1
Stamping dies-Round punches with 60°conical head and reduced shankJB/T 5828-20082008-7-1
Scrap cutters of stamping dies-Part 1:Round scrap cuttersJB/T 7651.1-20082008-7-1
Single punch plates of stamping dies-Part8:Bolster plates for ball-locked side-fixed single punchesJB/T 7644.8-20082008-7-1
Single punch plates of stamping dies-Part4:Bolster plates for side-fixed single punchesJB/T 7644.4-20082008-7-1
Technical specifications for press die setsJB/T 8050-20082008-7-1
Pilot pins of stamping dies-Part 2:Pilot pins-Type BJB/T 7647.2-20082008-7-1
Stamping die plates-Part 2:Rectangular retaining platesJB/T 7643.2-20082008-7-1
Pilot pins of stamping dies-Part 2:Pilot pins-Type BJB/T 7647.4-20082008-7-1
Pitch punch and stock guide units of stamping dies-Part 6:Stock supporting platesJB/T 7648.6-20082008-7-1
Cold chamber die casting machinesGB/T 21269-20072008-6-1
Pouring machine-Technical requirementsJB/T 6579-20072008-2-1
Rotator mixer-Technical requirementsJB/T 7457-20072008-2-1
Eddy-vibrating screenJB/T 5774-20072008-2-1
Muller and intensive mixer-Basic parametersJB/T 2656-20072008-2-1
Jolt and squeeze moulding machine jolt moulding machine-Technical requirementsJB/T 1430-20072008-2-1
Apron type shot blasting machine-Technical requirementsJB/T 5360-20072008-2-1
Air impact moulding machineJB/T 5773-20072008-2-1
Dust collector for foundry-General technical requirementsJB/T 10788-20072008-2-1
Single hook type airless and shot blasting machine-Technical requirementsJB/T 7459-20072008-2-1
Screw feeder-Technical requirementsJB/T 5363-20072008-2-1
Shell moulding mahine-Technical requirementsJB/T 5552-20072008-2-1
Elements for Cold Press Dies - Part 14: Limit PoleQJ 2514.14A-20072007-11-1
Elements for Cold Press Dies - Part 9: Minitype and Rhombus Universal HolderQJ 2514.9A-20072007-11-1
Elements for Cold Press Dies - Part 10: Guide Unit Type AQJ 2514.10A-20072007-11-1
Elements for Cold Press Dies - Part 12: Guide PillarsQJ 2514.12A-20072007-11-1
Elements for Cold Press Cold - Part 11: Guide Unit Type BQJ 2514.11A-20072007-11-1
Elements for Cold Press Dies - Part 1: Die PlateQJ 2514.1A-20072007-11-1
Technical Requirements for Cold Press Die ComponentsQJ 2522A-20072007-11-1
Elements for Cold Press Dies - Part 4: Backing PlateQJ 2514.4A-20072007-11-1
Elements for Cold Press Dies - Part 3: Stripper PlateQJ 2514.3A-20072007-11-1
Elements for Cold Press Dies - Part 16: Piercing and Locating SetQJ 2514.16A-20072007-11-1
Elements for Cold Press Dies - Part 13: Guide BushesQJ 2514.13A-20072007-11-1
Elements for Cold Press Dies - Part 8: Large and Medium Universal HolderQJ 2514.8A-20072007-11-1
Elements for Cold Press Dies - Part 15: Supporting BushesQJ 2514.15A-20072007-11-1
Elements for Cold Press Dies - Part 6: ShankQJ 2514.6A-20072007-11-1
Elements for Cold Press Dies - Part 2: Retaining PlateQJ 2514.2A-20072007-11-1
Elements for Cold Press Dies - Part 7: Pilot PinQJ 2514.7A-20072007-11-1
Elements for Cold Press Dies - Part 5: PunchQJ 2514.5A-20072007-11-1
Safety requirments for high pressure metal diecasting nuitsGB 20906-20072007-10-1
Safety requirements for foundry machineryGB 20905-20072007-10-1
Specification of plastic packaging mouldsGB/T 14663-20072007-9-1
Stamping dies—Gas springs—Part 1:General specificationGB/T 20914.1-20072007-9-1
Stamping dies—Elastomer pressure springs Part 1:General specificationGB/T 20915.1-20072007-9-1
Stamping dies—Gas springs—Part 2:Specification of accessoriesGB/T 20914.2-20072007-9-1
Stamping dies—Elastomer pressure springs—Part 2:Specifiction of AccessoriesGB/T 20915.2-20072007-9-1
Electrical vibrator-Part 1:Types and basic parametersJB/T 5548.1-20062007-7-1
Single disk blast wheel-Technical requirementsJB/T 6578-20062007-7-1
Entirely vertical motor die casting machines - Part 3 : Testing of the accuraciesJB/T 8353.3-20062007-7-1
Entirely vertical motor die casting machines - Part 2 : Technical requirementsJB/T 8353.2-20062007-7-1
Molten iron ladle-Part 2:Technical requirementsJB/T 5771.2-20062007-7-1
Electrical vibrator- Part 2:Technical requirementsJB/T 5548.2-20062007-7-1
Cold-box core shooter-Technical requirementsJB/T 5361-20062007-7-1
Molten steel ladleJB/T 6685-20062007-7-1
Cupola-Part 2:Basic parametersJB/T 6576.2-20062007-7-1
Molten iron ladle-Part 1:Basic parametersJB/T 5771.1-20062007-7-1
Entirely vertical motor rotor die casting machines - Part 1 : Basic parametersJB/T 8353.1-20062007-7-1
Components of injection moulds for plastics - Part 2: Straight guide bushGB/T 4169.2-20062007-4-1
Components of injection moulds for plastics - Part 5: Shouldered guide pillarGB/T 4169.5-20062007-4-1
Components of injection moulds for plastics - Part 4: Headed guide pillar GB/T 4169.4-20062007-4-1
Components of injection moulds for plastics - Part 6: Spacer blockGB/T 4169.6-20062007-4-1
Injection mould bases for plasticsGB/T 12555-20062007-4-1
Components of injection moulds for plastics - Part 14: Ejector guide pillarGB/T 4169.14-20062007-4-1
Components of injection moulds for plastics - Part 3: Headed guide bushGB/T 4169.3-20062007-4-1
Components of injection moulds for plastics - Part 18: Locating ring GB/T 4169.18-20062007-4-1
Components of injection moulds for plastics - Part 11: Round locating element GB/T 4169.11-20062007-4-1
Specifiication of injection moulds for plasticsGB/T 12554-20062007-4-1
Components of injection moulds for plastics - Part 10: Support pillarGB/T 4169.10-20062007-4-1
Components of injection moulds for plastics ― Part 8:Mould plateGB/T 4169.8-20062007-4-1
Components of injection moulds for plastics - Part 19: Sprue bushGB/T 4169.19-20062007-4-1
Components of injection moulds for plastics - Part 15: Flat ejector pinGB/T 4169.15-20062007-4-1
ShakeoutJB/T 6575-20062007-4-1
Components of injection moulds for plastics - Part 22: Round mould opening delayer GB/T 4169.22-20062007-4-1
Components of injection moulds for plastics - Part 21: Rectangular locating element GB/T 4169.21-20062007-4-1
Components of injection moulds for plastics - Part 20: Limit pinGB/T 4169.20-20062007-4-1
Components of injection moulds for plastics - Part 17: Ejector sleeve GB/T 4169.17-20062007-4-1
Specification of injection mould bases for plasticsGB/T 12556-20062007-4-1
Components of injection moulds for plastics - Part 12: Ejector guide bush GB/T 4169.12-20062007-4-1
Components of injection moulds for plastics - Part 1: Ejector pinGB/T 4169.1-20062007-4-1
Components of injection moulds for plastics - Part 9: Stop pin GB/T 4169.9-20062007-4-1
Components of injection moulds for plastics - Part 16: Shouldered ejector pinGB/T 4169.16-20062007-4-1
Components of injection moulds for plastics - Part 7: Ejector plateGB/T 4169.7-20062007-4-1
Components of injection moulds for plastics - Part 23: Rectangular mould opening delayerGB/T 4169.23-20062007-4-1
Specification of components of injection moulds for plastics GB/T 4170-20062007-4-1
Components of injection moulds for plastics ― Part 13: Return pinGB/T 4169.13-20062007-4-1
Tumbling barrel cleaning machineJB/T 504-20062007-3-1
Core shooterJB/T 2848-20062007-3-1
Low pressure diecasting machine - Technical requirementsJB/T 8608-20062007-3-1
Model formulating means of foundry machineryJB/T 3000-20062007-3-1
Barrel shot blasting machine-Technical requirementJB/T 5359-20062007-3-1
Machinery vibrating stress relief device Part 2:Technical requirementsJB/T 5925.2-20052005-9-1
Cupola Part 1:Technical requirementsJB/T 6576.1-20052005-9-1
Hot-chamber diecasting machine Part2:Testing of the accuracyJB/T 6309.2-20052005-9-1
Foundry machinery-general technical requirementJB/T 1644-20052005-9-1
Hot-chamber diecasting machine Part3:Technical requirementsJB/T 6309.3-20052005-9-1
Vibrating stress relief effect-Evaluation methodsJB/T 5926-20052005-9-1
Machinery vibrating stress relief device Part 1:Basic parametersJB/T 5925.1-20052005-9-1
Die-casting die components-Part 10: Ejector guide bushGB/T 4678.10-20032004-3-1
Die-casting die components-Part 5: Headed guide pillarGB/T 4678.5-20032004-3-1
Die-casting die components-Part 13: Ejector plate washerGB/T 4678.13-20032004-3-1
Die-casting die components--Part 19:Locating elementGB/T 4678.19-20032004-3-1
Die-casting die components-Part 3: Rectangular insert blockGB/T 4678.3-20032004-3-1
Die-casting die components-Part 2: Round insert blockGB/T 4678.2-20032004-3-1
Die-casting die components-Part 8: Ejector plateGB/T 4678.8-20032004-3-1
Specification of die-casting die componentsGB/T 4679-20032004-3-1
Die-casting die components--Part18:Support pillarGB/T 4678.18-20032004-3-1
Die-casting die components-Part 9: Ejector guide pillarGB/T 4678.9-20032004-3-1
Die-casting die components-Part 12: Return pinGB/T 4678.12-20032004-3-1
Die-casting die components-Part 1: Mould plateGB/T 4678.1-20032004-3-1
Die-casting die components-Part 6: Headed guide bushGB/T 4678.6-20032004-3-1
Die-casting die components-Part 15: Spacer blockGB/T 4678.15-20032004-3-1
Die-casting die components-Part 7: Straight guide bushGB/T 4678.7-20032004-3-1
Die-casting die components—Part16:Flat ejector pinGB/T 4678.16-20032004-3-1
Die-casting die components—Part17:Ejector sleeveGB/T 4678.17-20032004-3-1
Die-casting die components-Part 4: Shouldered guide pillarGB/T 4678.4-20032004-3-1
Die-casting die components-Part 14: Stop pinGB/T 4678.14-20032004-3-1
Small-sized Combination Die - Socket QJ 778.2(1)-19831994-11-1
Small-sized Combination Die - Cyclinder QJ 778.1(3)-19831994-11-1
Small-sized Combination Die - Plug Pin QJ 778.2(2)-19831994-11-1
Small-sized Combination Die - Cover Plate QJ 778.1(2)-19831994-11-1
Small-sized Combination Die - Support QJ 778.1(1)-19831994-11-1
Small-sized Combination Die - Hand Grip QJ 778.2(4)-19831994-11-1
Small-sized Combination Die - Plug Screw QJ 778.2(3)-19831994-11-1
Specification of the press toolsGB/T 14662-19931994-7-1
Specification of plastic packaging mouldGB/T 14663-19931994-7-1
Positioning Plate for Universal Trough Curve Mould (L≤600mm)QJ 2313.7-19921993-11-1
Female Die for Universal Trough Curve Mold (L≤2000mm)QJ 2315.4-19921992-11-1
Positioning Plate for Universal Trough Curve Mold (L≤2000mm)QJ 2315.7-19921992-11-1
Mold Shaft for Universal Trough Curve Mold (L≤220mm)QJ 2312.3-19921992-11-1
Universal Trough Curve Mold (L≤1200mm)QJ 2315-19921992-11-1
Male Mold of Universal Trough Curve Mold (L≤220mm) QJ 2312.2-19921992-11-1
Top Piece for Universal Trough Curve Mold (L≤2000mm)QJ 2315.5-19921992-11-1
Female Die for Universal Trough Curve Mold (L≤220mm) QJ 2312.4-19921992-11-1
Lower Holder of Universal Trough Curve Mold (L≤220mm) QJ 2312.1-19921992-11-1
Technical Conditions for Universal Trough Curve Mold QJ 2316-19921992-11-1
Splits of Universal Trough Curve Mold (L≤220mm) QJ 2312.10-19921992-11-1
Top Pole of Universal Trough Curve Mold (L≤2000mm)QJ 2315.6-19921992-11-1
Injection mould for plastic large-size mould bases -Guide pillars with headGB/T 12555.8-19901991-10-1
Injection mould for plastic large-size mould bases -Ejector platesGB/T 12555.6-19901991-10-1
Injection mould for plastic large-size mould bases -Guide pillars with shoulderGB/T 12555.9-19901991-10-1
Injection mould for plastic Specifications for medium size and small size mould basesGB/T 12556.2-19901991-10-1
Injection mould for plastic Medium size and small size mould basesGB/T 12556.1-19901991-10-1
Injection mould for plastic large-size mould bases -Guide pins for ejector platerGB/T 12555.10-19901991-10-1
Injection mould for plastic large-size mould bases -Stralght guide bushesGB/T 12555.11-19901991-10-1
Injection mould for plastic large-size mould bases --Standard mould basesGB/T 12555.1-19901991-10-1
Injection mould for plastic large-size mould bases-Elamping platesGB/T 12555.3-19901991-10-1
Injection mould for plastic large-size mould bases -Spacer platesGB/T 12555.7-19901991-10-1
Injection mould for plastic large-size mould bases -Return pinsGB/T 12555.13-19901991-10-1
Specification of injection mould for plasticsGB/T 12554-19901991-10-1
Injection mould for plastic large-size mould bases -Guide bushes with headGB/T 12555.12-19901991-10-1
Holder for ball slide die sets for press tools-Die holder for center pillar setsGB/T 2856.4-19901991-5-1
Guide unit for press tools-ClamprGB/T 2861.16-19901991-5-1
Guide unit for press tools-Guide pillar with taper lead, type BGB/T 2861.13-19901991-5-1
Guide unit for press tools-Guide bushes, type BGB/T 2861.7-19901991-5-1
Guide unit for press tools-BushingGB/T 2861.14-19901991-5-1
Guide unit for press tools-Guide pillar with taper lead, type AGB/T 2861.12-19901991-5-1
Guide unit for press tools-WasherGB/T 2861.15-19901991-5-1
Sliding guide die sets for press tools-Back pillar sets (narrow)GB/T 2851.4-19901991-5-1
Holder for sliding guide die sets for press tools-Punch holder for back pillar setsGB/T 2855.5-19901991-5-1
Holder for ball slide die sets for press tools-Die holder for back pillar setsGB/T 2855.6-19901991-5-1
Guide unit for press tools-Guide bushes, type CGB/T 2861.8-19901991-5-1
Holder for sliding guide die sets for press tools-Die holder for back pillar sets (narrow)GB/T 2855.8-19901991-5-1
Holder for sliding guide die sets for press tools-Punch holder for back pillar sets (narrow)GB/T 2855.7-19901991-5-1
Ball slide die sets for press tools-Center pillar setsGB/T 2852.2-19901991-5-1
Guide unit for press tools-Guide pillars, type CGB/T 2861.3-19901991-5-1
Holder for ball slide die sets for press tools-Punch holder for four pillar setsGB/T 2856.5-19901991-5-1
Holder for sliding guide die sets for press tools-Punch holder for center pillar sets (round)GB/T 2855.11-19901991-5-1
Holder for sliding guide die sets for press tools-Die holder for center pillar sets (round)GB/T 2855.12-19901991-5-1
Guide unit for press tools-Guide pillars, type BGB/T 2861.2-19901991-5-1
Sliding guide die sets for press tools-Center pillar sets (round)GB/T 2851.6-19901991-5-1
Guide unit for press dies-CageGB/T 2861.10-19901991-5-1
Holder for ball silde die sets for press tools-Punch holder for center pillar setsGB/T 2856.3-19901991-5-1
Guide unit for press tools-Cylindrical coil compression springGB/T 2861.11-19901991-5-1
Terminology of forging dies and elementsGB/T 9453-19881989-3-1
Terminology for die-casting dieGB/T 8847-19881988-9-1
Terminology for diesGB/T 8845-19881988-9-1
Terminology of mould for plasticsGB/T 8846-19881988-9-1
Specification of the die-casting diesGB/T 8844-20031988-8-1
Methods for chemical analysis of silica sand for foundryGB/T 7143-19861987-10-1
Multifunctional Combined Stamping Die Holder - Cheese Head Screw QJ 959.2-19851986-6-1
Plastic Extrusion Mould - Guide Pillar QJ 884-19841986-3-1
Plastic Extrusion Mould - Hand Shank QJ 889.1-19841986-3-1
Plastic Extrusion Mould - Hand Shank QJ 889.2-19841986-3-1
Plastic Extrusion Mould - Rectangle Plastic Extrusion MouldQJ 870.3-19841986-3-1
Plastic Extrusion Mould - Cavity Plate QJ 874.2-19841986-3-1
Plastic Extrusion Mould - Base Plate QJ 877.5-19841986-3-1
Plastic Extrusion Mould - Base Plate QJ 877.7-19841986-3-1
Plastic Extrusion Mould - Circular Loading Cavity QJ 881.1-19841986-3-1
Plastic Extrusion Mould - Combined Thread Core (For Fixing Inserts)QJ 890.1-19841986-3-1
Plastic Extrusion Mould - Push Rod QJ 886.2-19841986-3-1
Plastic Extrusion Mould - Cavity Plate QJ 873.2-19841986-3-1
Plastic Extrusion Mould - Push Rod QJ 886.3-19841986-3-1
Plastic Extrusion Mould - Rectangle Plastic Extrusion MouldQJ 870.1-19841986-3-1
Plastic Extrusion Mould - Circular Plastic Extrusion MouldQJ 869.3-19841986-3-1
Plastic Extrusion Mould - Positioning Pin QJ 885-19841986-3-1
Plastic Extrusion Mould - Circular Plastic Press Mould QJ 867.1-19841986-3-1
Plastic Extrusion Mould - Fixed Plate QJ 879.4-19841986-3-1
Back
About Us Contact Us Payment
Tel: +86-10-8572 5655 | Fax: +86-10-8581 9515 Email: coc@codeofchina.com | Send me a messageQQ: 672269886
Copyright: Codeofchina Inc 2008-2020