1 Scope
This standard specifies the terms and definitions, requirements, test methods, inspection rules, packaging, marking, transportation and storage for the woven belts.
This standard is applicable to the woven belts made of such fibrous materials as purified cotton, chinlon, vinylon, acrylon, polypropylene fiber and dacron. Elastic woven belts may be implemented by reference to this standard.
2 Normative References
The following referenced documents are indispensable references, only the edition cited applies. For the dated normative references, only the dated editions are applicable to this document. For undated references, the latest edition of the normative document (including all amendments) referred to applies.
GB/T 250 Textiles—Tests for colour fastness—Grey scale for assessing change in colour
GB/T 251 Textiles—Tests for colour fastness—Grey scale for assessing staining
GB/T 2828.1-2003 Sampling procedures for inspection by attributes-Part1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
GB/T 3820 Determination of thickness of textiles and textile products
GB/T 3920 Textiles—Tests for colour fastness—Colour fastness to rubbing
GB/T 3922 Textiles--Testing method for colour fastness to perspiration
GB 5296.4 Instructions for use of products of consumer interest--Instructions for use of textiles and apparel
GB/T 8427-2008 Textiles - Tests for color fastness - Color fastness to artificial light: Xenon arc fading lamp test
GB 18401 National General Safety Technical Code for Textile Products
FZ/T 01018 Textiles-woven fabrics defect terminology
FZ/T 60021-2010 Test method for physical properties of belt
3 Terms and Definitions
Terms and definitions established in FZ/T 01018 and the following ones are applicable to this document.
3.1
Skips
Warp or weft not interwoven along the texture, but floating on the belt surface.
3.2
Open-set mark
Obvious gap between two adjacent wefts of woven belt
3.3
Buckle
Metal auxiliaries matching with belt
4 Requirements
4.1 Technical requirements of woven belts are divided into inherent quality and appearance quality. Inherent quality requirements include seven indexes: width deviation, weft direction density deviation ratio, thickness deviation, length deviation, colour fastness to perspiration, colour fastness to rubbing and colour fastness to light. Appearance quality requirements mainly include the appearance defects.
4.2 Inherent quality requirements of woven belts are detailed in Table 1.
Foreword i
1 Scope
2 Normative References
3 Terms and Definitions
4 Requirements
5 Grading Requirements
6 Test Methods
7 Inspection Rules
8 Packaging, Marking, Transportation and Storage
9 Others
1 Scope
This standard specifies the terms and definitions, requirements, test methods, inspection rules, packaging, marking, transportation and storage for the woven belts.
This standard is applicable to the woven belts made of such fibrous materials as purified cotton, chinlon, vinylon, acrylon, polypropylene fiber and dacron. Elastic woven belts may be implemented by reference to this standard.
2 Normative References
The following referenced documents are indispensable references, only the edition cited applies. For the dated normative references, only the dated editions are applicable to this document. For undated references, the latest edition of the normative document (including all amendments) referred to applies.
GB/T 250 Textiles—Tests for colour fastness—Grey scale for assessing change in colour
GB/T 251 Textiles—Tests for colour fastness—Grey scale for assessing staining
GB/T 2828.1-2003 Sampling procedures for inspection by attributes-Part1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
GB/T 3820 Determination of thickness of textiles and textile products
GB/T 3920 Textiles—Tests for colour fastness—Colour fastness to rubbing
GB/T 3922 Textiles--Testing method for colour fastness to perspiration
GB 5296.4 Instructions for use of products of consumer interest--Instructions for use of textiles and apparel
GB/T 8427-2008 Textiles - Tests for color fastness - Color fastness to artificial light: Xenon arc fading lamp test
GB 18401 National General Safety Technical Code for Textile Products
FZ/T 01018 Textiles-woven fabrics defect terminology
FZ/T 60021-2010 Test method for physical properties of belt
3 Terms and Definitions
Terms and definitions established in FZ/T 01018 and the following ones are applicable to this document.
3.1
Skips
Warp or weft not interwoven along the texture, but floating on the belt surface.
3.2
Open-set mark
Obvious gap between two adjacent wefts of woven belt
3.3
Buckle
Metal auxiliaries matching with belt
4 Requirements
4.1 Technical requirements of woven belts are divided into inherent quality and appearance quality. Inherent quality requirements include seven indexes: width deviation, weft direction density deviation ratio, thickness deviation, length deviation, colour fastness to perspiration, colour fastness to rubbing and colour fastness to light. Appearance quality requirements mainly include the appearance defects.
4.2 Inherent quality requirements of woven belts are detailed in Table 1.
Contents of FZ/T 63005-2010
Foreword i
1 Scope
2 Normative References
3 Terms and Definitions
4 Requirements
5 Grading Requirements
6 Test Methods
7 Inspection Rules
8 Packaging, Marking, Transportation and Storage
9 Others
