Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
This Standard replace FZ/T 81004-1991 "Skirts and Skirted Suit".
Compared with FZ/T 81004-1991, this Standard has the following main changes:
——Adjust the application scope of the Standard;
——Add the quality technical requirements of skirt, one-piece dress and skirted suit;
——Supplement the normative references;
——Revise the requirements on splicing and color difference;
——add the specifications of warp and weft directions;
——Cancel Position 4 of finished product;
——Cancel on the content on 5 · 3 series;
——Add inspection indices of distortion rate of tight skirt products;
——Add the assessment for the peeled off strength of the position covered with adhesive interlining and the slipping degree of seam;
——Add the limit of the formaldehyde content emitted from finished product;
——Add the limit of pH value of finished product;
——Add the requirements in allowable degrees of dry cleaning fastness, dry friction fastness, wet friction fastness and light fastness for finished products;
——Add the requirements of dimensional change ratio of finished product after washing;
——Add the requirements in the allowable degree of fuzzing and pilling of finished product;
——Divide the product quality grades into superior quality product, first-grade product and qualified product;
——Supplement and improve the contents related to the quality defect determination of finished products;
——Add Appendix A "Test Methods for Slipping Degree of Seam".
Annex A of this standard is normative.
This Standard was proposed by the China National Textile and Apparel Council.
This national standard is under the jurisdiction of the National Technical Committee 219 on Garments of Standardization Administration of China.
Drafting organizations: Shenzhen Academy of Metrology& Quality Inspection, Shanghai Garment Research Institute, National Garments Quality Inspection and Supervision Center (Shanghai), Wenzhou Institute of technology Testing & Quality, Zhejiang Xuege Fashion Co., Ltd., Wensli Group Co., Ltd.
Chief drafting staffs: Yang Zhimin, Xu Jian, Zhan Zuqin, Tu Hongyan, Ma Qianfang, Zhang Aizhen, Lin Ouwen, Cheng Mili, Chen Guoqiang, Qin Wei
This Standard was firstly issued in 1991, and firstly revised this time.
Contents
1 Scope 1
2 Normative References 1
3 Requirements 2
4 Inspection (test) method 8
5 Inspection Classification Rules 11
6 Marking, Packaging, Transportation and Storage 16
Appendix A (Normative) Test method for determining seam slipping 17
Skirts and Skirted Suit
1 Scope
This standard specifies requirements, inspection method, inspection rules, marking, packing, transportation and storage of skirt, one-piece dress and skirted suit.
This standard is applicable to mass-produced skirt, one-piece dress and skirted suit made of raw materials like cotton, hemp, silk, chemical fiber and blend fabric.
2 Normative References
Provisions of the following documents, through reference in this standard, constitute provisions of this standard. For dated reference, subsequent amendments to, or revisions of, any of these publications do not apply. Parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For undated references, the latest editions of the normative documents are applicable to this standard.
GB 250 Gray scale for assessing change in colour
GB 251 Gray scale for assessing staining
GB/T 1335.2 Standard sizing systems for garments - Women
GB/T 1335.3 Standard sizing systems for garments - Children
GB/T 2910-1997 Textile - Binary fibre mixtures - Quantitative chemical analysis
GB/T 2911-1997 Textiles - Ternary fibre mixtures - Quantitative analysis
GB/T 2912- 11998 Textiles - Determination of Formaldehyde - Part 1: Free and Hydrolized Formaldehyde (Water Extraction Method)
GB/T 3920-1997 Textiles - Tests for colour fastness - Colour fastness to rubbing
GB/T 3921.1-1997 Textiles - Tests for colour fastness - colour fastness to washing: Test 1
GB/T 3921.3-1997 Textiles - Tests for colour fastness - colour fastness to washing: Test 3
GB/T 3922-1995 Textiles - Testing method for colour fastness to perspiration
GB/T 4802.1-1997 Textiles - Assessing the rate of pilling of fabrics - Circular locus method
GB 5296.4 Instructions for use of products of consumer interest - Instructions for use of textiles and apparel
GB/T 5711-1997 Textiles - Tests for colour fastness - Colour fastness to dry cleaning
GB/T 7573-2002 Textiles - Determination of pH of the aqueous extract
GB/T 8427-1998 Textiles - Tests for colour fastness - Colour fastness to artificial light: Xenon arc fading lamp test
GB/T 8629-2001 Textiles - Domestic washing and drying procedures for textile testing
GB/T 18132 Silk garment
FZ/T 01053 Textiles - Identification of fiber content
FZ/T 01057-1999 Test method for identification of textile fibers
FZ/T 20019-1999 Test method for determining the seam slipping of wool woven fabrics
FZ/T 80002 Marking, packaging, transportation and storage for garments
FZ/T 80007.1 Test method of peeled off strength value for garments used adhesive interlining
FZ/T 80007.3 Dry wash resistance test method for garments used adhesive interlining
3 Requirements
3.1 Instructions for use
Instructions for use of finished product shall comply with the requirements of GB 5296.4.
3.2 Specification for size designation
3.2.1 Size designation setting shall comply with the requirements of GB/T 1335.2 and GB/T 1335.3.
3.2.2 Specifications of main positions of finished product shall be designed by self according to the relevant requirements of GB/T 1335.2 and GB/T 1335.3.
3.3 Materials
3.3.1 Shell fabric
Shell fabric suitable for skirt, one-piece dress and skirted suit shall be selected according to the textile shell fabrics standards.
3.3.2 Lining
Lining with property and color matching with the shell fabric used shall be adopted (excluding the special design).
3.3.3 Accessories
3.3.3.1 Lining cloth, shoulder pad
Adhesive interlining and shoulder pads with shrinkage, property, and color matching with the shell fabric used shall be selected, and the quality shall meet the requirements of corresponding product standards.
3.3.3.2 Stitch thread
Stitch thread suitable for the quality of accessories used shall be adopted. The shrinkage of embroidery thread shall match with the shell fabric. Button thread shall match with the color of button. Brand thread shall match with the brand ground colour (except ornamental thread).
3.3.3.3 Button, zipper and metallic auxiliaries
Button (except ornamental button) and auxiliaries suitable for the shell fabric used shall be adopted. Zipper and metal auxiliaries shall be free from defects. Buttons and auxiliaries shall be rustless, and free of deformation and discolouring after washing and ironing.
3.4 Warp and weft direction
3.4.1 Allowable skewness degree of top collar, back, sleeve and straight skirt shall not be larger than 3%, and the front fly hem is not turned.
3.4.2 The skew weft of colored woven checks shall not be greater than 3%.
3.5 Stripe and plaid matching
3.5.1 Apparent stripes or plaids of over 1.0cm, if on shell fabric, shall comply with the requirements of Table 1.
Table 1 Unit: cm
Position name Requirements on stripe or plaid matching Remarks
Left and right front Stripe matching of strip material; plaid matching of plaid material; the mutual deviation shall not be greater than 0.3. If the sizes of plaids are different, take the upper part of one half coat length.
Bag and front fly Stripe matching of strip material and plaid matching of plaid material, the mutual deviation shall not be greater than 0.3. If the sizes of plaids are different, take the front part of pocket.
Collar point, lapel The stripe material shall be symmetrical, and the mutual deviation shall not be greater than 0.2. If checker board weaves exist, take the obvious one.
Back yoke Stripes shall be smooth and straight, the mutual deviation not greater than 0.4 Subject to the obvious stripes
Cuff button Left and right cuff button stripes and plaids are smooth and straight, symmetrical to the vertical stripes, and the mutual deviation not greater than 0.2 Subject to the obvious stripes
Long sleeve Stripe and plaid shall be smooth and straight; subject to sleeve cap, two sleeves shall be symmetrical; the mutual deviation shall not be greater than 0.5. —
Short sleeve Stripe and plaid shall be smooth and straight; subject to cuff, two sleeves shall be symmetrical; the mutual deviation shall not be greater than 0.5. —
Sleeve and front fly The part above elbow line and the front fly checks are be aligned horizontally, and the mutual deviation on two sleeves is not larger than 0.5. —
Center back seam Stripe matching of strip material; plaid matching of plaid material; the mutual deviation shall not be greater than 0.3. —
Side seam Plaid matching of plaid material; the mutual deviation 10.0 below the arm hole is not larger than 0.4. —
Skirt side seam Stripes shall be straight, plaids across each other, the mutual deviation shall not be greater than 0.3. —
Note: it is exclusive of special design.
3.5.2 The fabric (velvet), checker board weave raw material and the whole body shall be in the same direction; the whole part of long-hair raw materials shall be in the same direction (excluding the special design).
3.5.3 Shell fabric with special pattern shall subject to the main picture, and the whole body shall be in the same direction.
1 Scope
2 Normative References
3 Requirements
4 Inspection (test) method
5 Inspection Classification Rules
6 Marking, Packaging, Transportation and Storage
Appendix A (Normative) Test method for determining seam slipping
Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
This Standard replace FZ/T 81004-1991 "Skirts and Skirted Suit".
Compared with FZ/T 81004-1991, this Standard has the following main changes:
——Adjust the application scope of the Standard;
——Add the quality technical requirements of skirt, one-piece dress and skirted suit;
——Supplement the normative references;
——Revise the requirements on splicing and color difference;
——add the specifications of warp and weft directions;
——Cancel Position 4 of finished product;
——Cancel on the content on 5 · 3 series;
——Add inspection indices of distortion rate of tight skirt products;
——Add the assessment for the peeled off strength of the position covered with adhesive interlining and the slipping degree of seam;
——Add the limit of the formaldehyde content emitted from finished product;
——Add the limit of pH value of finished product;
——Add the requirements in allowable degrees of dry cleaning fastness, dry friction fastness, wet friction fastness and light fastness for finished products;
——Add the requirements of dimensional change ratio of finished product after washing;
——Add the requirements in the allowable degree of fuzzing and pilling of finished product;
——Divide the product quality grades into superior quality product, first-grade product and qualified product;
——Supplement and improve the contents related to the quality defect determination of finished products;
——Add Appendix A "Test Methods for Slipping Degree of Seam".
Annex A of this standard is normative.
This Standard was proposed by the China National Textile and Apparel Council.
This national standard is under the jurisdiction of the National Technical Committee 219 on Garments of Standardization Administration of China.
Drafting organizations: Shenzhen Academy of Metrology& Quality Inspection, Shanghai Garment Research Institute, National Garments Quality Inspection and Supervision Center (Shanghai), Wenzhou Institute of technology Testing & Quality, Zhejiang Xuege Fashion Co., Ltd., Wensli Group Co., Ltd.
Chief drafting staffs: Yang Zhimin, Xu Jian, Zhan Zuqin, Tu Hongyan, Ma Qianfang, Zhang Aizhen, Lin Ouwen, Cheng Mili, Chen Guoqiang, Qin Wei
This Standard was firstly issued in 1991, and firstly revised this time.
Contents
1 Scope 1
2 Normative References 1
3 Requirements 2
4 Inspection (test) method 8
5 Inspection Classification Rules 11
6 Marking, Packaging, Transportation and Storage 16
Appendix A (Normative) Test method for determining seam slipping 17
Skirts and Skirted Suit
1 Scope
This standard specifies requirements, inspection method, inspection rules, marking, packing, transportation and storage of skirt, one-piece dress and skirted suit.
This standard is applicable to mass-produced skirt, one-piece dress and skirted suit made of raw materials like cotton, hemp, silk, chemical fiber and blend fabric.
2 Normative References
Provisions of the following documents, through reference in this standard, constitute provisions of this standard. For dated reference, subsequent amendments to, or revisions of, any of these publications do not apply. Parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For undated references, the latest editions of the normative documents are applicable to this standard.
GB 250 Gray scale for assessing change in colour
GB 251 Gray scale for assessing staining
GB/T 1335.2 Standard sizing systems for garments - Women
GB/T 1335.3 Standard sizing systems for garments - Children
GB/T 2910-1997 Textile - Binary fibre mixtures - Quantitative chemical analysis
GB/T 2911-1997 Textiles - Ternary fibre mixtures - Quantitative analysis
GB/T 2912- 11998 Textiles - Determination of Formaldehyde - Part 1: Free and Hydrolized Formaldehyde (Water Extraction Method)
GB/T 3920-1997 Textiles - Tests for colour fastness - Colour fastness to rubbing
GB/T 3921.1-1997 Textiles - Tests for colour fastness - colour fastness to washing: Test 1
GB/T 3921.3-1997 Textiles - Tests for colour fastness - colour fastness to washing: Test 3
GB/T 3922-1995 Textiles - Testing method for colour fastness to perspiration
GB/T 4802.1-1997 Textiles - Assessing the rate of pilling of fabrics - Circular locus method
GB 5296.4 Instructions for use of products of consumer interest - Instructions for use of textiles and apparel
GB/T 5711-1997 Textiles - Tests for colour fastness - Colour fastness to dry cleaning
GB/T 7573-2002 Textiles - Determination of pH of the aqueous extract
GB/T 8427-1998 Textiles - Tests for colour fastness - Colour fastness to artificial light: Xenon arc fading lamp test
GB/T 8629-2001 Textiles - Domestic washing and drying procedures for textile testing
GB/T 18132 Silk garment
FZ/T 01053 Textiles - Identification of fiber content
FZ/T 01057-1999 Test method for identification of textile fibers
FZ/T 20019-1999 Test method for determining the seam slipping of wool woven fabrics
FZ/T 80002 Marking, packaging, transportation and storage for garments
FZ/T 80007.1 Test method of peeled off strength value for garments used adhesive interlining
FZ/T 80007.3 Dry wash resistance test method for garments used adhesive interlining
3 Requirements
3.1 Instructions for use
Instructions for use of finished product shall comply with the requirements of GB 5296.4.
3.2 Specification for size designation
3.2.1 Size designation setting shall comply with the requirements of GB/T 1335.2 and GB/T 1335.3.
3.2.2 Specifications of main positions of finished product shall be designed by self according to the relevant requirements of GB/T 1335.2 and GB/T 1335.3.
3.3 Materials
3.3.1 Shell fabric
Shell fabric suitable for skirt, one-piece dress and skirted suit shall be selected according to the textile shell fabrics standards.
3.3.2 Lining
Lining with property and color matching with the shell fabric used shall be adopted (excluding the special design).
3.3.3 Accessories
3.3.3.1 Lining cloth, shoulder pad
Adhesive interlining and shoulder pads with shrinkage, property, and color matching with the shell fabric used shall be selected, and the quality shall meet the requirements of corresponding product standards.
3.3.3.2 Stitch thread
Stitch thread suitable for the quality of accessories used shall be adopted. The shrinkage of embroidery thread shall match with the shell fabric. Button thread shall match with the color of button. Brand thread shall match with the brand ground colour (except ornamental thread).
3.3.3.3 Button, zipper and metallic auxiliaries
Button (except ornamental button) and auxiliaries suitable for the shell fabric used shall be adopted. Zipper and metal auxiliaries shall be free from defects. Buttons and auxiliaries shall be rustless, and free of deformation and discolouring after washing and ironing.
3.4 Warp and weft direction
3.4.1 Allowable skewness degree of top collar, back, sleeve and straight skirt shall not be larger than 3%, and the front fly hem is not turned.
3.4.2 The skew weft of colored woven checks shall not be greater than 3%.
3.5 Stripe and plaid matching
3.5.1 Apparent stripes or plaids of over 1.0cm, if on shell fabric, shall comply with the requirements of Table 1.
Table 1 Unit: cm
Position name Requirements on stripe or plaid matching Remarks
Left and right front Stripe matching of strip material; plaid matching of plaid material; the mutual deviation shall not be greater than 0.3. If the sizes of plaids are different, take the upper part of one half coat length.
Bag and front fly Stripe matching of strip material and plaid matching of plaid material, the mutual deviation shall not be greater than 0.3. If the sizes of plaids are different, take the front part of pocket.
Collar point, lapel The stripe material shall be symmetrical, and the mutual deviation shall not be greater than 0.2. If checker board weaves exist, take the obvious one.
Back yoke Stripes shall be smooth and straight, the mutual deviation not greater than 0.4 Subject to the obvious stripes
Cuff button Left and right cuff button stripes and plaids are smooth and straight, symmetrical to the vertical stripes, and the mutual deviation not greater than 0.2 Subject to the obvious stripes
Long sleeve Stripe and plaid shall be smooth and straight; subject to sleeve cap, two sleeves shall be symmetrical; the mutual deviation shall not be greater than 0.5. —
Short sleeve Stripe and plaid shall be smooth and straight; subject to cuff, two sleeves shall be symmetrical; the mutual deviation shall not be greater than 0.5. —
Sleeve and front fly The part above elbow line and the front fly checks are be aligned horizontally, and the mutual deviation on two sleeves is not larger than 0.5. —
Center back seam Stripe matching of strip material; plaid matching of plaid material; the mutual deviation shall not be greater than 0.3. —
Side seam Plaid matching of plaid material; the mutual deviation 10.0 below the arm hole is not larger than 0.4. —
Skirt side seam Stripes shall be straight, plaids across each other, the mutual deviation shall not be greater than 0.3. —
Note: it is exclusive of special design.
3.5.2 The fabric (velvet), checker board weave raw material and the whole body shall be in the same direction; the whole part of long-hair raw materials shall be in the same direction (excluding the special design).
3.5.3 Shell fabric with special pattern shall subject to the main picture, and the whole body shall be in the same direction.
Contents of FZ/T 81004-2003
1 Scope
2 Normative References
3 Requirements
4 Inspection (test) method
5 Inspection Classification Rules
6 Marking, Packaging, Transportation and Storage
Appendix A (Normative) Test method for determining seam slipping
