Detail of HG/T 20584-2011

Introduction of HG/T 20584-2011

1 Scope 1.0.1 This standard is the supplement and concretization of the fabrication part in "Steel pressure vessels" GB 150 in combination with the specific conditions of steel chemical vessels. 1.0.2 Unless otherwise specified, the application scope of this standard is the same as that of "Steel Pressure Vessels" GB 150. 2 Normative References The following referenced documents are indispensable for the application of this standard. For dated references, only the dated editions are applicable to this standard. For undated references, the latest edition (including all amendments) is applicable to this standard. Steel pressure vessels GB 150 General Purpose Metric Screw Threads-Basic Dimensions GB/T 196 General purpose metric screw threads-Tolerances GB/T 197 Steel Plates for Boiler and Pressure Vessels GB 713 Double end studs (clamping type)-Product grade BGB/T 901 Designation System for Fasteners GB/T 1237 Tolerances for Fasteners--Bolts, Screws, Studs and Nuts GB/T 3103.1 Methods of Radiographic Testing and Classification of Radiographs for Steel Castings GB/T 5677 Fasteners-surface discontinuities-bolts, screws and studs for general requirements GB/T 5779.1 Fasteners-surface discontinuities-nuts GB/T 5779.2 Fasteners-Surface Discontinuities-Bolts, Screws and Studs for Special Requirements GB/T 5779.3 Rust Grades and Preparation Grades of Steel Surfaces before Application of Paints and Related Products GB/T 8923 General purpose metric screw threads-Limits of sizes for the screw threads of medium quality and preferable plan GB/T 9145 Methods of liquid penetrant testing and classification of indication for steel castings GB/T 9443 The methods for magnetic particle testing and for specifying quality levels of steel castings GB/T 9444 Specification for welding of stainless steel clad steel plate GB/T 13148 Specification of design base for steel chemical vessels HG/T 20580 Specification of Materials Selection for Steel Chemical Vessels HG/T 20581 Specification for Stress Calculation of Steel Chemical Vessels HG/T 20582 Specification for Structural Design of Steel Chemical Vessels HG/T 20583 Technical Specification for Steel Low Temperature Pressure Vessels HG/T 20585 Detailed management rules for manufacturing of austenitic stainless steel pressure vessels HG/T 2806 Stud bolts JB/T 4707 Welding Procedure Qualification for Steel Pressure Vessels JB 4708 Welding Specification for Steel Pressure Vessels JB/T 4709 Carbon and low-alloy steel forgings for pressure vessels JB/T 4726 Low-alloy steel forgings for low temperature pressure vessels JB/T 4727 Stainless steel forgings for pressure vessels JB/T 4728 Nondestructive Testing of Pressure Equipments JB/T 4730 Coating and packing for pressure vessels transport JB/T 4711 General purpose screw threads-Selected sizes for commercial screws, bolts and nuts JB/T 7912 Ultrasonic inspection methods for steel castings JB/ZQ 6109 Supervision regulation on safety technology for stationary pressure vessel TSG R0004-2009 3 Terms and Definitions In addition to the terms and definitions given in "Steel pressure vessels", GB 150, for the purposes of this standard, the following terms and definitions apply. 3.0.1 Simulated postwelding heat treatment It refers to all postwelding heat treatment procedures experienced while simulating the actual fabricating process of materials with the testing plate or the materials of testing pieces at a temperature below Ac1(transformation temperature) or above 480℃. It is divided into two types-simulated short-period post-welding heat treatment and simulated long-period post-welding heat treatment 3.0.2 Simulated short-period post-welding heat treatment It refers to a postwelding heat treatment period experienced while simulating the actual fabricating process of materials with sample plate and sample material at a temperature below Ac1(transformation temperature) or above 480℃. 3.0.3 Simulated long-period post-welding heat treatment It refers to all postwelding heat treatment procedures experienced while simulating the actual fabricating process of materials with sample plate and sample material at a temperature below Ac1(transformation temperature) or above 480℃,and it includes the postwelding heat treatments after one or several times of repairing. At least one times of postwelding heat treatment shall be reserved for the user's future applying. 3.0.4 Vessel axes It refers to a straight line perpendicular to the reference surface center.

Contents of HG/T 20584-2011

Foreword i 1 Scope 2 Normative References 3 Terms and Definitions 4 Generals 5 Manufacture Used Raw Materials 6 Fabrication and Forming 7 Welding and Cutting 8 Post Welding Heat Treatment 9 Size Tolerances 10 Bolts and Screw Holes 11 Test and Examination 12 Surface Treatment, Painting, Packing and Transportation Annex A (Informative Annex) Leakage Test for Pressure Vessels by Using Ammonia Annex B (Informative Annex) Leakage Test for Pressure Vessels by Using Helium Annex C (Informative Annex) Leakage Test for Pressure Vessels by Using Halogen Annex D (Informative Annex) Commonly Equipment Used Anticorrosion Painting Annex E (Informative Annex) Fundamental Standards of Bolts, Studs and Nuts