This standard specifies terms and definitions, requirements, test methods and inspection rules of vehicle ignition coil.
This standard is applicable to inductance storage type vehicle ignition coil.
2 Normative references
The following referenced documents are indispensable for the application of this standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 2423.10 Environmental testing for electric and electronic products - Part 2: Tests methods - Test Fc: Vibration (sinusoidal)
GB/T 2828.1-2012 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
GB 18655-2010 Vehicles boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers
GB/T 19951-2005 Road vehicles - Test methods for electrical disturbances from electrostatic discharge
GB/T 21437.2 Road vehicles - Electrical disturbances from conduction and coupling - Part 2: Electrical transient conduction along supply lines only
GB/T 21437.3 Road vehicles - Electrical disturbances from conduction and coupling - Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines
GB/T 28046.1-2011 Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 1: General
GB/T 28046.4-2011 Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 4: Climatic loads
GB/T 33014.2-2016 Road vehicles - Component test methods for electrical/electronic disturbances from narrowband radiated electromagnetic energy - Part 2: Absorber-lined shielded enclosure
QC/T 413 Basic specification for automotive electrical equipment
3 Terms and definitions
For the purposes of this standard, the following terms and definitions apply.
3.1
maximum secondary output voltage, Usm
maximum absolute value of the secondary output voltage
3.2
primary resistance, Rp
resistance of primary coil
3.3
primary current, Ip
current that passes through the primary coil
3.4
interruption current, Ipi
Foreword i 1 Scope 2 Normative references 3 Terms and definitions 4 Requirements 5 Test method 6 Inspection rules 7 Marking, packaging, transport and storage
1 Scope
This standard specifies terms and definitions, requirements, test methods and inspection rules of vehicle ignition coil.
This standard is applicable to inductance storage type vehicle ignition coil.
2 Normative references
The following referenced documents are indispensable for the application of this standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 2423.10 Environmental testing for electric and electronic products - Part 2: Tests methods - Test Fc: Vibration (sinusoidal)
GB/T 2828.1-2012 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
GB 18655-2010 Vehicles boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers
GB/T 19951-2005 Road vehicles - Test methods for electrical disturbances from electrostatic discharge
GB/T 21437.2 Road vehicles - Electrical disturbances from conduction and coupling - Part 2: Electrical transient conduction along supply lines only
GB/T 21437.3 Road vehicles - Electrical disturbances from conduction and coupling - Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines
GB/T 28046.1-2011 Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 1: General
GB/T 28046.4-2011 Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 4: Climatic loads
GB/T 30038-2013 Road vehicles - Degrees of electrical equipment protection (IP-code)
GB/T 33014.2-2016 Road vehicles - Component test methods for electrical/electronic disturbances from narrowband radiated electromagnetic energy - Part 2: Absorber-lined shielded enclosure
QC/T 413 Basic specification for automotive electrical equipment
3 Terms and definitions
For the purposes of this standard, the following terms and definitions apply.
3.1
maximum secondary output voltage, Usm
maximum absolute value of the secondary output voltage
3.2
primary resistance, Rp
resistance of primary coil
3.3
primary current, Ip
current that passes through the primary coil
3.4
interruption current, Ipi
Contents of QC/T 16-2016
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Test method
6 Inspection rules
7 Marking, packaging, transport and storage
