This standard specifies the technical requirements, test methods, inspection rules, marking, packaging, storage and preservation for automotive electrical equipment.
This standard is applicable to automotive electrical equipment (electronic engines, appliances and electronic products, hereinafter referred to as products).
2 Normative References
The following documents contain provisions which, through reference in this standard, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding any corrigendum), or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For undated references, the latest edition of the document referred to applies.
GB 191 Packaging - Pictorial Marking for Handling of Goods (eqv ISO 780)
GB/T 2423.1 Basic Environmental Testing Procedures for Electric and Electronic Products - Tests A: Cold (eqv IEC 68-2-1)
GB/T 2423.2 Basic Environmental Testing Procedures for Electric and Electronic Products Tests B: Dry Heat (eqv IEC 68-2-2)
GB/T 2423.10 Environmental Testing for Electric and Electronic Products - Part 2: Test Methods Test Fc and Guidance: Vibration (Sinusoidal) (idt IEC 68-2-6)
GB/T 2423.17 Basic Environmental Testing Procedures for Electric and Electronic Products Test Ka: Salt Mist (eqv IEC 68-2-11)
GB/T 2423.22 Basic Environmental Testing Procedures for Electric and Electronic Products Test N: Change of Temperature (eqv IEC 68-2-14)
GB/T 2423.34 Basic Environmental Testing Procedures for Electric and Electronic Products; Test Z/AD: Composite Temperature/Humidity Cyclic Test (idt IEC 68-2-38)
GB/T 2828 In-batch Inspection Computation Sampling Procedure and Sampling Table (Applicable to In-batch Inspection)
GB/T 4942.1 Classification of Degrees of Protection Provided by Enclosures for Rotating Machines (eqv IEC 34-5)
GB/T 4942.2 Degrees of Protection Provided by Enclosures for Low-voltage Apparatus (eqv IEC 947-1)
GB/T 10069.1 Measurement of Airborne Noise Emitted by Rotating Electrical Machinery and the Noise Limits-Engineering Method for the Measurement of Airborne Noise (neq ISO 1680.1)
GB/T 13306 Plates
GB/T 17619 Limits and Methods of Testing for Immunity of Electrical/Electronic Sub-assemblies in Vehicles to Electromagnetic Radiation (adopting EC Instruction 95/54/EC)
GB 18655 Limits and Methods of Measurement of Radio Disturbance Characteristics for the Protection of Receivers Used on Board Vehicles (idt CISPR 25)
QC/T 238 Storage and Preservation for Automotive Parts
QC/T 438 Technical Specification for High-voltage Plastic Pieces of Automobile Ignition System
QC/T 625 Metallic Coatings and Conversion Coatings for Automobile
QC/T 29106 Technical Specification Of Low-voltage Electric Harness For Motor Vehicles
ISO 7637 Road Vehicles - Electrical Disturbances from Conduction and Coupling
3 Technical Requirements
3.1 General provisions for products
3.1.1 Document of products
Products shall meet the requirements of this standard and classified product standards and be manufactured in accordance with drawing and design document approved by specified procedures.
Foreword i 1 Scope 2 Normative References 3 Technical Requirements 4 Test Methods 5 Inspection Rules 6 Marking, Packaging, Storage and Preservation
1 Scope
This standard specifies the technical requirements, test methods, inspection rules, marking, packaging, storage and preservation for automotive electrical equipment.
This standard is applicable to automotive electrical equipment (electronic engines, appliances and electronic products, hereinafter referred to as products).
2 Normative References
The following documents contain provisions which, through reference in this standard, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding any corrigendum), or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For undated references, the latest edition of the document referred to applies.
GB 191 Packaging - Pictorial Marking for Handling of Goods (eqv ISO 780)
GB/T 2423.1 Basic Environmental Testing Procedures for Electric and Electronic Products - Tests A: Cold (eqv IEC 68-2-1)
GB/T 2423.2 Basic Environmental Testing Procedures for Electric and Electronic Products Tests B: Dry Heat (eqv IEC 68-2-2)
GB/T 2423.10 Environmental Testing for Electric and Electronic Products - Part 2: Test Methods Test Fc and Guidance: Vibration (Sinusoidal) (idt IEC 68-2-6)
GB/T 2423.17 Basic Environmental Testing Procedures for Electric and Electronic Products Test Ka: Salt Mist (eqv IEC 68-2-11)
GB/T 2423.22 Basic Environmental Testing Procedures for Electric and Electronic Products Test N: Change of Temperature (eqv IEC 68-2-14)
GB/T 2423.34 Basic Environmental Testing Procedures for Electric and Electronic Products; Test Z/AD: Composite Temperature/Humidity Cyclic Test (idt IEC 68-2-38)
GB/T 2828 In-batch Inspection Computation Sampling Procedure and Sampling Table (Applicable to In-batch Inspection)
GB/T 4942.1 Classification of Degrees of Protection Provided by Enclosures for Rotating Machines (eqv IEC 34-5)
GB/T 4942.2 Degrees of Protection Provided by Enclosures for Low-voltage Apparatus (eqv IEC 947-1)
GB/T 10069.1 Measurement of Airborne Noise Emitted by Rotating Electrical Machinery and the Noise Limits-Engineering Method for the Measurement of Airborne Noise (neq ISO 1680.1)
GB/T 13306 Plates
GB/T 17619 Limits and Methods of Testing for Immunity of Electrical/Electronic Sub-assemblies in Vehicles to Electromagnetic Radiation (adopting EC Instruction 95/54/EC)
GB 18655 Limits and Methods of Measurement of Radio Disturbance Characteristics for the Protection of Receivers Used on Board Vehicles (idt CISPR 25)
QC/T 238 Storage and Preservation for Automotive Parts
QC/T 438 Technical Specification for High-voltage Plastic Pieces of Automobile Ignition System
QC/T 625 Metallic Coatings and Conversion Coatings for Automobile
QC/T 29106 Technical Specification Of Low-voltage Electric Harness For Motor Vehicles
ISO 7637 Road Vehicles - Electrical Disturbances from Conduction and Coupling
3 Technical Requirements
3.1 General provisions for products
3.1.1 Document of products
Products shall meet the requirements of this standard and classified product standards and be manufactured in accordance with drawing and design document approved by specified procedures.
Contents of QC/T 413-2002
Foreword i
1 Scope
2 Normative References
3 Technical Requirements
4 Test Methods
5 Inspection Rules
6 Marking, Packaging, Storage and Preservation
