1 Scope
This standard specifies the material, making, assembly, test and preparation for shipment for burners of tubular heater in petrochemical industry.
This standard is applicable to the burners for tubular heater fuel oil and fuel gas in petrochemical industry.
2 Normative References
The following referenced documents are indispensable for the application of this standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 1804-2000 General Tolerances - Tolerances for Linear and Angular Dimensions without Individual Tolerance Indications
GB/T 2988 High Alumina Bricks
GB/T 6414-1999 Castings - System of Dimensional Tolerances and Machining Allowances
GB/T 8923.1 Preparation of Steel Substrates before Application of Paints and Related Products - Visual Assessment of Surface Cleanliness - Part 1: Rust Grades and Preparation Grades of Uncoated Steel Substrates and of Steel Substrates after Overall Removal of Previous Coatings
GB/T 7350-1999 Waterproof Packaging
SH/T 3602-2009 Testing and Measurements Code of Burner for Petrochemical Tubular Heater
TSG ZB002 Type Test Rule for Oil and Gas Burners
3 Material
3.1 The material for making burners shall meet the requirements of design documents. If not specified in the design documents, the burner assembly shall at least meet the requirements of Table 3.1.
Foreword i
1 Scope
2 Normative References
3 Material
4 Making
5 Assembly
6 Test
7 Preparation for Shipment
7.1 Anti-corrosion
7.2 Packing
7.3 Nameplate
7.4 Documentation
Explanation of Wording in this Standard
SH/T 3113-2016, SH 3113-2016, SHT 3113-2016, SH/T3113-2016, SH/T 3113, SH/T3113, SH3113-2016, SH 3113, SH3113, SHT3113-2016, SHT 3113, SHT3113
Introduction of SH/T 3113-2016
1 Scope
This standard specifies the material, making, assembly, test and preparation for shipment for burners of tubular heater in petrochemical industry.
This standard is applicable to the burners for tubular heater fuel oil and fuel gas in petrochemical industry.
2 Normative References
The following referenced documents are indispensable for the application of this standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 1804-2000 General Tolerances - Tolerances for Linear and Angular Dimensions without Individual Tolerance Indications
GB/T 2988 High Alumina Bricks
GB/T 6414-1999 Castings - System of Dimensional Tolerances and Machining Allowances
GB/T 8923.1 Preparation of Steel Substrates before Application of Paints and Related Products - Visual Assessment of Surface Cleanliness - Part 1: Rust Grades and Preparation Grades of Uncoated Steel Substrates and of Steel Substrates after Overall Removal of Previous Coatings
GB/T 7350-1999 Waterproof Packaging
SH/T 3602-2009 Testing and Measurements Code of Burner for Petrochemical Tubular Heater
TSG ZB002 Type Test Rule for Oil and Gas Burners
3 Material
3.1 The material for making burners shall meet the requirements of design documents. If not specified in the design documents, the burner assembly shall at least meet the requirements of Table 3.1.
Contents of SH/T 3113-2016
Foreword i
1 Scope
2 Normative References
3 Material
4 Making
5 Assembly
6 Test
7 Preparation for Shipment
7.1 Anti-corrosion
7.2 Packing
7.3 Nameplate
7.4 Documentation
Explanation of Wording in this Standard