1 Scope
This Standard specifies the technical requirements, functional specification, test methods and inspection rules of distribution automation system.
This Standard is applicable to various feeder circuit terminal unit and medium-voltage monitoring and control unit (distribution automation and management system sub-station) as well as distribution transformer terminal unit suitable for distribution network with 10kV or above. Measurement and control unit installed dispersedly which is applicable to shielded area and outdoors may refer to it.
2 Normative references
The following standards contain provisions which, through reference in this Standard, constitute provisions of this Standard. At time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below.
GB 4208-1993 Degrees of Protection Provided by Enclosure (IP code)
GB/T 13729-1992 General Specification for Remote Terminal Unit
GB/T 15153.1-1998 "Telecontrol Equipment and Systems - Part 2: Operating Conditions - Section 1: Power Supply and Electromagnetic Compatibility" (idt IEC 60870-2-1:1995)
GB/T 17626.4-1998 Electromagnetic Compatibility-Testing and Measurement Techniques-Electrical Fast Transient/Burst Immunity Test" (idt IEC 61000-4-4:1995)
DL/T 630-1997 Technical Requirement for RTU with A. C. Electrical Quantities Input Discrete Sampling
DL/T 634-1997 Telecontrol Equipment and Systems - Part 5: Transmission Protocols - Section 101: Companion Standard for Basic Telecontrol Tasks (neq IEC 870-5 101:1995)
IEC 870-2-2:1996 Telecontrol Equipment and Systems - Part 2: Operation Condition - Section 2: Environmental Conditions (Climate, Mechanical and Other Non- electric Influence Factors)
IEC 61334-5-1:2001 Distribution Automation Using Distribution Line Carrier Systems Communication Protocols
3 Definitions
3.1 Remote Terminal Unit - RTU Suitable of Distribution Automation System
Foreword I
1 Scope
2 Normative references
3 Definitions
4 Technical Requirements
5 Test Methods
6 Inspection Rules
7 Marking, Packing, Transport and Storage
Appendix A (Normative) Circuit Against High Frequency Interference Test
Appendix B (Normative) Circuit of Fast Transient Burst Interference Resistance Test
Appendix C (Normative) Wiring Drawings of Electrostatic Discharge Test
Appendix D (Informative) Supplementary Explanations of Fast-Calibration-Process in DL/T 634-1997
1 Scope
This Standard specifies the technical requirements, functional specification, test methods and inspection rules of distribution automation system.
This Standard is applicable to various feeder circuit terminal unit and medium-voltage monitoring and control unit (distribution automation and management system sub-station) as well as distribution transformer terminal unit suitable for distribution network with 10kV or above. Measurement and control unit installed dispersedly which is applicable to shielded area and outdoors may refer to it.
2 Normative references
The following standards contain provisions which, through reference in this Standard, constitute provisions of this Standard. At time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below.
GB 4208-1993 Degrees of Protection Provided by Enclosure (IP code)
GB/T 13729-1992 General Specification for Remote Terminal Unit
GB/T 15153.1-1998 "Telecontrol Equipment and Systems - Part 2: Operating Conditions - Section 1: Power Supply and Electromagnetic Compatibility" (idt IEC 60870-2-1:1995)
GB/T 17626.4-1998 Electromagnetic Compatibility-Testing and Measurement Techniques-Electrical Fast Transient/Burst Immunity Test" (idt IEC 61000-4-4:1995)
DL/T 630-1997 Technical Requirement for RTU with A. C. Electrical Quantities Input Discrete Sampling
DL/T 634-1997 Telecontrol Equipment and Systems - Part 5: Transmission Protocols - Section 101: Companion Standard for Basic Telecontrol Tasks (neq IEC 870-5 101:1995)
IEC 870-2-2:1996 Telecontrol Equipment and Systems - Part 2: Operation Condition - Section 2: Environmental Conditions (Climate, Mechanical and Other Non- electric Influence Factors)
IEC 61334-5-1:2001 Distribution Automation Using Distribution Line Carrier Systems Communication Protocols
3 Definitions
3.1 Remote Terminal Unit - RTU Suitable of Distribution Automation System
Contents of DL/T 721-2000
Foreword I
1 Scope
2 Normative references
3 Definitions
4 Technical Requirements
5 Test Methods
6 Inspection Rules
7 Marking, Packing, Transport and Storage
Appendix A (Normative) Circuit Against High Frequency Interference Test
Appendix B (Normative) Circuit of Fast Transient Burst Interference Resistance Test
Appendix C (Normative) Wiring Drawings of Electrostatic Discharge Test
Appendix D (Informative) Supplementary Explanations of Fast-Calibration-Process in DL/T 634-1997
