Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
This standard is developed in accordance with the rules given in GB/T 1.1-2009.
This standard replaces FZ/T 01028-1993 Horizontal method for determination of textile fabrics combustion performance, and the following main technical changes have been made with respect to FZ/T 01028-1993:
—— the standard name is revised to Textiles - Burning behaviour - Determination of flame spread rate of horizontally oriented specimens;
—— in Clause 2 “Normative references”, GB/T 8629 is added;
—— the term "burning rate" is modified to "flame spread rate” or “rate of flame spread”;
—— the contents of Clause 4 "Principle" and Clause 5 "Health and safety of test personnel" are modified;
—— the detailed description is added for the horizontal burning test chamber (see 6.1.1);
—— the detailed description and requirements are modified for the specimen clamp, and a specimen clamp without heat-resistant metal mesh is added (see 6.1.2);
—— the description is added for the specimen holder (see 6.1.3);
—— the schematic diagram is modified for the horizontal burning test chamber (see Figure 1);
—— the schematic diagrams are added for the dimension of horizontal burning test chamber (see Figure 2) and the dimension of catch tray (see Figure 3);
—— the schematic diagram is modified for the specimen clamp (see Figures 4 and 5);
—— the standard dimension of specimen is modified from "350mm×100mm" to "340mm×100mm" (see 7.1.1), and the length of specimen with width less than 60mm is modified from "350mm" to "340mm" (see 7.1.2.1);
—— the note "Refer to GB/T 1804 for the tolerance" is added in the schematic diagram for test equipment;
—— the requirement of "If necessary, test the burning behaviour after washing" is added, and the washing procedure requirements are specified (see 7.5);
—— 8.1 in the clause "Test procedures” of the previous standard is taken as a separate clause in this standard;
—— “Note 1” and “Note 2” are added in 9.2;
—— 9.5 is added.
This standard was proposed by China National Textile and Apparel Council.
This standard is under the jurisdiction of Basic Standard Subcommittee of Technical Committee 209 on Textiles of Standardization Administration of China (SAC/TC 209/SC 1).
The previous edition of this standard is as follows:
—— FZ/T 01028-1993.
Textiles - Burning behaviour - Determination of flame spread rate of horizontally oriented specimens
1 Scope
This standard specifies the test method for determining the burning behaviour of horizontally oriented fabrics by bottom edge ignition.
This standard is applicable to various fabrics and its products.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 6529 Textiles - Standard atmospheres for conditioning and testing
GB/T 8629 Textiles - Domestic washing and drying procedures for textile testing
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
burning time
time required for the flame to spread a certain distance on the burning material under the specified test conditions
3.2
flame spread rate; rate of flame spread
distance of flame front spread per unit time under the specified test conditions
[GB/T 14644-2014, definition 3.2]
4 Principle
Under specified conditions, ignite the center of the bottom edge of the horizontally oriented specimen. After a certain flame application time, measure the burning distance and burning time of the specimen and calculate the flame spread rate.
5 Health and safety of test personnel
The burning of textiles may produce fume and toxic gases that affect the health of operating personnel, so the test personnel shall wear gas masks. Test instruments may be installed in the fume hood, and fume and smoke dust shall be removed after each test. However, the ventilation system shall be closed during the burning of the specimen, so as not to affect the test results.
6 Equipment and materials
6.1 Horizontal burning tester.
6.1.1 Horizontal burning test chamber: made of heat-resistant and fume-resistant materials. The front part of the chamber is provided with an observation door made of heat-resistant and fume-resistant transparent materials. The chamber is provided with 10 vents with a diameter of 19mm at the bottom, and a tray for catching molten drips is placed under the chamber. The catch tray is placed between two rows of vents without affecting the ventilation of the vents. A ventilation slot is arranged respectively at the four edge of the chamber top. The chamber is provided with a small door on the left and right sides respectively, one for taking and placing the specimen clamp, and the other for connecting the gas pipe. A horizontal specimen holder is arranged inside the chamber. The whole test chamber is supported by four support legs with a height of 10mm. See Figures 1, 2 and 3.
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Health and safety of test personnel
6 Equipment and materials
7 Specimen preparation
8 Test conditions
9 Test procedures
10 Result calculation
11 Test report
Bibliography
Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
This standard is developed in accordance with the rules given in GB/T 1.1-2009.
This standard replaces FZ/T 01028-1993 Horizontal method for determination of textile fabrics combustion performance, and the following main technical changes have been made with respect to FZ/T 01028-1993:
—— the standard name is revised to Textiles - Burning behaviour - Determination of flame spread rate of horizontally oriented specimens;
—— in Clause 2 “Normative references”, GB/T 8629 is added;
—— the term "burning rate" is modified to "flame spread rate” or “rate of flame spread”;
—— the contents of Clause 4 "Principle" and Clause 5 "Health and safety of test personnel" are modified;
—— the detailed description is added for the horizontal burning test chamber (see 6.1.1);
—— the detailed description and requirements are modified for the specimen clamp, and a specimen clamp without heat-resistant metal mesh is added (see 6.1.2);
—— the description is added for the specimen holder (see 6.1.3);
—— the schematic diagram is modified for the horizontal burning test chamber (see Figure 1);
—— the schematic diagrams are added for the dimension of horizontal burning test chamber (see Figure 2) and the dimension of catch tray (see Figure 3);
—— the schematic diagram is modified for the specimen clamp (see Figures 4 and 5);
—— the standard dimension of specimen is modified from "350mm×100mm" to "340mm×100mm" (see 7.1.1), and the length of specimen with width less than 60mm is modified from "350mm" to "340mm" (see 7.1.2.1);
—— the note "Refer to GB/T 1804 for the tolerance" is added in the schematic diagram for test equipment;
—— the requirement of "If necessary, test the burning behaviour after washing" is added, and the washing procedure requirements are specified (see 7.5);
—— 8.1 in the clause "Test procedures” of the previous standard is taken as a separate clause in this standard;
—— “Note 1” and “Note 2” are added in 9.2;
—— 9.5 is added.
This standard was proposed by China National Textile and Apparel Council.
This standard is under the jurisdiction of Basic Standard Subcommittee of Technical Committee 209 on Textiles of Standardization Administration of China (SAC/TC 209/SC 1).
The previous edition of this standard is as follows:
—— FZ/T 01028-1993.
Textiles - Burning behaviour - Determination of flame spread rate of horizontally oriented specimens
1 Scope
This standard specifies the test method for determining the burning behaviour of horizontally oriented fabrics by bottom edge ignition.
This standard is applicable to various fabrics and its products.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 6529 Textiles - Standard atmospheres for conditioning and testing
GB/T 8629 Textiles - Domestic washing and drying procedures for textile testing
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
burning time
time required for the flame to spread a certain distance on the burning material under the specified test conditions
3.2
flame spread rate; rate of flame spread
distance of flame front spread per unit time under the specified test conditions
[GB/T 14644-2014, definition 3.2]
4 Principle
Under specified conditions, ignite the center of the bottom edge of the horizontally oriented specimen. After a certain flame application time, measure the burning distance and burning time of the specimen and calculate the flame spread rate.
5 Health and safety of test personnel
The burning of textiles may produce fume and toxic gases that affect the health of operating personnel, so the test personnel shall wear gas masks. Test instruments may be installed in the fume hood, and fume and smoke dust shall be removed after each test. However, the ventilation system shall be closed during the burning of the specimen, so as not to affect the test results.
6 Equipment and materials
6.1 Horizontal burning tester.
6.1.1 Horizontal burning test chamber: made of heat-resistant and fume-resistant materials. The front part of the chamber is provided with an observation door made of heat-resistant and fume-resistant transparent materials. The chamber is provided with 10 vents with a diameter of 19mm at the bottom, and a tray for catching molten drips is placed under the chamber. The catch tray is placed between two rows of vents without affecting the ventilation of the vents. A ventilation slot is arranged respectively at the four edge of the chamber top. The chamber is provided with a small door on the left and right sides respectively, one for taking and placing the specimen clamp, and the other for connecting the gas pipe. A horizontal specimen holder is arranged inside the chamber. The whole test chamber is supported by four support legs with a height of 10mm. See Figures 1, 2 and 3.
Contents of FZ/T 01028-2016
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Health and safety of test personnel
6 Equipment and materials
7 Specimen preparation
8 Test conditions
9 Test procedures
10 Result calculation
11 Test report
Bibliography
