GB 14048.6-2008 Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters AC semiconductor motor controllers and starters(including soft-starter) (English Version)
Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters AC semiconductor motor controllers and starters(including soft-starter)
This standard applies to controllers and starters, which may include a series mechanical switching device, intended to be connected to circuits, the rated voltage of which does not exceed 1000V a.c.
This standard characterizes controllers and starters with and without bypass means.
Controllers and starters dealt with in this Part are not normally designed to interrupt short-circuit currents. Therefore, suitable short-circuit protection (see 8.2.5) shall form part of the installation, but not necessarily of the controller or starter.
In this context, this Part gives requirements for controllers and starters associated with separate short-circuit protective devices.
This standard does not apply to:
-The motor speeds of the continuous operation a.c. motors at abnormal speed;
-Semiconductor equipment controlling non-motor loads, including semiconductor contactors (see 2.2.13 of GB 14048.1);
-Electronic a.c. power controllers covered by IEC 60146.
Contactors and control circuit devices used in controllers and starters shall comply with the requirements of their relevant product standard. Where mechanical switching devices are used, they shall meet the requirements of their own national standard, and the additional requirements of this Part.
The object of this Part is to state as follows:
-The characteristics of controllers and starters and associated equipment;
-The conditions with which controllers and starters shall comply with reference to:
a) Their operation properties;
b) Their dielectric properties;
c) The degrees of protection provided by their enclosures where applicable;
d) Their construction;
-The tests intended for confirming that these conditions have been met, and the methods to be adopted for these tests;
-The information to be given with the equipment, or in the manufacturer's literature.
Forward I 1 Scope 2 Normative references 3 Terms and Definitions 4 Classification 5 Characteristics of AC Semiconductor Motor Controllers and Starters 6 Product Information 7 Normal Service, Mounting and Transport Conditions 8 Constructional and Performance Requirements 9 Tests Annex A (Normative) Marking and Identification of Terminals Annex B (Normative) Overload Relays or Releases Annex C (Normative) Discrimination between Overload Protective Devices and SCPDs Annex D (Normative) Requirements for Radiated Emission Testing Annex E (Informative) Method of Converting GB 4824 Radiated Emission Limits to Transmitted Power Equivalents Annex F (Informative) Operating Capability Annex G (Informative) Examples of Control Circuit Configurations Annex H (Informative) Items Subject to Agreement between Manufacturer and User Annex I (Normative) Modified Test Circuit for Short-circuit Testing of Semiconductor Motor Controllers and Starters Annex J (Informative) Flowchart for Constructing Bypassed Semiconductor Controllers Tests Bibliography
GB 14048.6-2008 Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters AC semiconductor motor controllers and starters(including soft-starter) (English Version)
Standard No.
GB 14048.6-2008
Status
superseded
Language
English
File Format
PDF
Word Count
20000 words
Price(USD)
500.0
Implemented on
2009-1-1
Delivery
via email in 1 business day
Detail of GB 14048.6-2008
Standard No.
GB 14048.6-2008
English Name
Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters AC semiconductor motor controllers and starters(including soft-starter)
1 Scope
This standard applies to controllers and starters, which may include a series mechanical switching device, intended to be connected to circuits, the rated voltage of which does not exceed 1000V a.c.
This standard characterizes controllers and starters with and without bypass means.
Controllers and starters dealt with in this Part are not normally designed to interrupt short-circuit currents. Therefore, suitable short-circuit protection (see 8.2.5) shall form part of the installation, but not necessarily of the controller or starter.
In this context, this Part gives requirements for controllers and starters associated with separate short-circuit protective devices.
This standard does not apply to:
-The motor speeds of the continuous operation a.c. motors at abnormal speed;
-Semiconductor equipment controlling non-motor loads, including semiconductor contactors (see 2.2.13 of GB 14048.1);
-Electronic a.c. power controllers covered by IEC 60146.
Contactors and control circuit devices used in controllers and starters shall comply with the requirements of their relevant product standard. Where mechanical switching devices are used, they shall meet the requirements of their own national standard, and the additional requirements of this Part.
The object of this Part is to state as follows:
-The characteristics of controllers and starters and associated equipment;
-The conditions with which controllers and starters shall comply with reference to:
a) Their operation properties;
b) Their dielectric properties;
c) The degrees of protection provided by their enclosures where applicable;
d) Their construction;
-The tests intended for confirming that these conditions have been met, and the methods to be adopted for these tests;
-The information to be given with the equipment, or in the manufacturer's literature.
Contents of GB 14048.6-2008
Forward I
1 Scope
2 Normative references
3 Terms and Definitions
4 Classification
5 Characteristics of AC Semiconductor Motor Controllers and Starters
6 Product Information
7 Normal Service, Mounting and Transport Conditions
8 Constructional and Performance Requirements
9 Tests
Annex A (Normative) Marking and Identification of Terminals
Annex B (Normative) Overload Relays or Releases
Annex C (Normative) Discrimination between Overload Protective Devices and SCPDs
Annex D (Normative) Requirements for Radiated Emission Testing
Annex E (Informative) Method of Converting GB 4824 Radiated Emission Limits to Transmitted Power Equivalents
Annex F (Informative) Operating Capability
Annex G (Informative) Examples of Control Circuit Configurations
Annex H (Informative) Items Subject to Agreement between Manufacturer and User
Annex I (Normative) Modified Test Circuit for Short-circuit Testing of Semiconductor Motor Controllers and Starters
Annex J (Informative) Flowchart for Constructing Bypassed Semiconductor Controllers Tests
Bibliography
