GB 18564.1-2006 Road tanker for dangerous liquid goods transportation - Part 1: Technical requirements of atmospheric pressure metal tank (English Version)
1.1 This part specifies technical requirements for design, manufacture, test methods, end-of-manufacturing inspection, coating, marking and identification, and periodic inspection items of the atmospheric pressure metal tank of road tanker for dangerous liquid goods (hereinafter referred to as "tank body").
1.2 This part is applicable to the tank body being used for loading and transporting the dangerous liquid goods, with working pressure less than 0.1 MPa, manufactured with metal material, and having permanent connection with finalized automobile chassis or semitrailer frame.
1.3 This part is applicable to the media given in Appendix A. As for the media beyond the scope of Appendix A, if their physical and chemical properties are similar to those listed in Appendix A, they also may be made reference to this part.
1.4 This part not applicable to the non-metal tank body, tank body of vacuum insulation structure or the tank body used for the military equipment having special requirements.
1.5 As for the tank body that shall not be designed according to this part, it is allowed to adopt the following methods for design, but they shall pass the assessment and confirmation of the unit approved by the national authority:
- Stress analysis, including finite element method;
- Replication experiment analysis (such as experimental stress analysis and replication hydraulic pressure test);
- Comparison experience design with comparable in-service structures.
Foreword I 1 Scope 2 Normative References 3 Terms and Definitions 4 General Provisions 5 Design 6 Manufacture 7 Test Methods 8 End-of-manufacturing Inspection 9 Coating, Marking and Identification 10 Storage 11 End-of-manufacturing Documents 12 Periodic Inspection Appendix A (Normative) Common Dangerous Liquid Good Media and Their Main Design Parameters Appendix B (Informative) Compatibility between Common Dangerous Liquid Good Media and Tank Body Material Appendix C (Informative) Design Calculation of Safety Relief Device Appendix D (Normative) Tank Body with Non-circular Cross Section
GB 18564.1-2006 Road tanker for dangerous liquid goods transportation - Part 1: Technical requirements of atmospheric pressure metal tank (English Version)
Standard No.
GB 18564.1-2006
Status
superseded
Language
English
File Format
PDF
Word Count
15000 words
Price(USD)
370.0
Implemented on
2006-11-1
Delivery
via email in 1 business day
Detail of GB 18564.1-2006
Standard No.
GB 18564.1-2006
English Name
Road tanker for dangerous liquid goods transportation - Part 1: Technical requirements of atmospheric pressure metal tank
1.1 This part specifies technical requirements for design, manufacture, test methods, end-of-manufacturing inspection, coating, marking and identification, and periodic inspection items of the atmospheric pressure metal tank of road tanker for dangerous liquid goods (hereinafter referred to as "tank body").
1.2 This part is applicable to the tank body being used for loading and transporting the dangerous liquid goods, with working pressure less than 0.1 MPa, manufactured with metal material, and having permanent connection with finalized automobile chassis or semitrailer frame.
1.3 This part is applicable to the media given in Appendix A. As for the media beyond the scope of Appendix A, if their physical and chemical properties are similar to those listed in Appendix A, they also may be made reference to this part.
1.4 This part not applicable to the non-metal tank body, tank body of vacuum insulation structure or the tank body used for the military equipment having special requirements.
1.5 As for the tank body that shall not be designed according to this part, it is allowed to adopt the following methods for design, but they shall pass the assessment and confirmation of the unit approved by the national authority:
- Stress analysis, including finite element method;
- Replication experiment analysis (such as experimental stress analysis and replication hydraulic pressure test);
- Comparison experience design with comparable in-service structures.
Contents of GB 18564.1-2006
Foreword I
1 Scope
2 Normative References
3 Terms and Definitions
4 General Provisions
5 Design
6 Manufacture
7 Test Methods
8 End-of-manufacturing Inspection
9 Coating, Marking and Identification
10 Storage
11 End-of-manufacturing Documents
12 Periodic Inspection
Appendix A (Normative) Common Dangerous Liquid Good Media and Their Main Design Parameters
Appendix B (Informative) Compatibility between Common Dangerous Liquid Good Media and Tank Body Material
Appendix C (Informative) Design Calculation of Safety Relief Device
Appendix D (Normative) Tank Body with Non-circular Cross Section
