1 Scope
This standard specifies technical requirements and inspection rules of complete popular karting (hereafter referred to as "karting") and its components.
This standard is applicable to the appraisal inspection, acceptance inspection and arbitration inspection of karting produced and operated within the territory of China and imported karting.
2 Normative References
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections) to, or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 2828 Sampling Procedures and Tables for Lot-by-lot Inspection by Attributes (Apply to Inspection of Successive Lots or Batches)
GB 19196 Kart Classification & Homologation
GB 19197 Criteria for Karting Circuit Construction
HG/T 2177 Appearance Quality of Tyres
JB 3677 Tightening Torque for Automotive Threaded Fasteners
JB/T 5943 Engineering Machinery - General Technical Specifications for Welding Parts
3 Technical Requirements
3.1 Basic Requirements
Design, manufacture and repair of the karting shall meet the safety requirements. The karting shall be free from any defect causing harm to personal safety of karter and other personnel. The karting can be operated only after it is in a safe state.
3.2 Operating Conditions
The karting shall be operated at the field complying with GB 19197.
Foreword i
1 Scope
2 Normative References
3 Technical Requirements
3.1 Basic Requirements
3.2 Operating Conditions
3.3 Construction of Karting
3.4 Operating Performance
3.5 Occupant Protection
3.6 Noise
3.7 Chassis
3.8 Engine
3.9 Brake System
3.10 Steering System
3.11 Running Gear
3.12 Transmission System
3.13 Fuel System
3.14 Non-metal Materials
3.15 Seat
3.16 Frame
3.17 Safety Devices
3.18 Marking
4 Inspection Rules
4.1 Inspection Classification
4.2 Sampling
4.3 Appraisal Inspection
4.4 Quality Conformity Inspection
Figure 1 Structural Diagram for Indoor Karting
Table 1 Sample Size and Inspection Lot Number for Critical Defect Items
Table 2 Sample Size and Inspection Lot Number for Major Defect Items
Table 3 Sample Size and Inspection Lot Number for Minor Defect Items
1 Scope
This standard specifies technical requirements and inspection rules of complete popular karting (hereafter referred to as "karting") and its components.
This standard is applicable to the appraisal inspection, acceptance inspection and arbitration inspection of karting produced and operated within the territory of China and imported karting.
2 Normative References
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections) to, or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 2828 Sampling Procedures and Tables for Lot-by-lot Inspection by Attributes (Apply to Inspection of Successive Lots or Batches)
GB 19196 Kart Classification & Homologation
GB 19197 Criteria for Karting Circuit Construction
HG/T 2177 Appearance Quality of Tyres
JB 3677 Tightening Torque for Automotive Threaded Fasteners
JB/T 5943 Engineering Machinery - General Technical Specifications for Welding Parts
3 Technical Requirements
3.1 Basic Requirements
Design, manufacture and repair of the karting shall meet the safety requirements. The karting shall be free from any defect causing harm to personal safety of karter and other personnel. The karting can be operated only after it is in a safe state.
3.2 Operating Conditions
The karting shall be operated at the field complying with GB 19197.
Contents of GB 19195-2003
Foreword i
1 Scope
2 Normative References
3 Technical Requirements
3.1 Basic Requirements
3.2 Operating Conditions
3.3 Construction of Karting
3.4 Operating Performance
3.5 Occupant Protection
3.6 Noise
3.7 Chassis
3.8 Engine
3.9 Brake System
3.10 Steering System
3.11 Running Gear
3.12 Transmission System
3.13 Fuel System
3.14 Non-metal Materials
3.15 Seat
3.16 Frame
3.17 Safety Devices
3.18 Marking
4 Inspection Rules
4.1 Inspection Classification
4.2 Sampling
4.3 Appraisal Inspection
4.4 Quality Conformity Inspection
Figure 1 Structural Diagram for Indoor Karting
Table 1 Sample Size and Inspection Lot Number for Critical Defect Items
Table 2 Sample Size and Inspection Lot Number for Major Defect Items
Table 3 Sample Size and Inspection Lot Number for Minor Defect Items
