Detail of GB/T 12467.5-2009

Introduction of GB/T 12467.5-2009

1 Scope This part of GB/T 12467 specifies the standard documents with which it is necessary to conform to claim conformity to the quality requirements of GB/T 12467.2, GB/T 12467.3 or GB/T 12467.4. This part is applicable to assess and certify the welding capacity of manufacturers, and shall be used in conjunction with GB/T 12467.2, GB/T 12467.3 and GB/T 12467.4. 2 Standard Documents Need to Conform to Claim Conformity to the Quality Requirements 2.1 General principles To claim conformity to the quality requirements of GB/T 12467.2, GB/T 12467.3 and GB/T 12467.4, the product standards of a manufacturer is required to conform either to the standards listed in 2.2 or to other standards that provide technically equivalent conditions. It is the responsibility of the manufacturer to demonstrate technically equivalent conditions when standards other than those specified in 2.2 are employed. Certificates (or claims of compliance by a manufacturer) shall clearly identify the standards used by the manufacturer. 2.2 Standard documents When manufacturers are welding in accordance with GB/T 12467.2, GB/T 12467.3 and GB/T 12467.4, they shall adopt the valid editions of the following standard documents. GB/T 9445 Non-destructive Testing-Qualification and Certification of Personnel (GB/T 9445-2008, ISO 9712:2005, IDT) GB/T 15169 Qualification test of welders-Fusion welding for steels (GB/T 15169-2003, ISO/DIS 9606-1:2002, IDT) GB/T 18591 Welding--Guidance on the measurement of preheating temperature, interpass temperature and preheat maintenance temperature (GB/T 18591-2001, ISO 13916:1996, IDT) GB/T 19419 Welding coordination-Tasks and responsibilities (GB/T 19419-2003, ISO 14731:1997, IDT) GB/T 19805 Qualification test of welding operators (GB/T 19805-2005, ISO 14732:1998, IDT) GB/T 19866 Specification and Qualification of Welding Procedures for Metallic Materials-General Rules (GB/T 19866-2005, ISO 15607:2003, IDT) GB/T 19867.1 Welding Procedure Specification for Arc Welding (GB/T 19867.1-2005, ISO 15609-1:2004, IDT) GB/T 19867.2 Welding Procedure Specification for Gas Welding (GB/T 19867.2-2008, ISO 15609-2:2001, IDT) GB/T 19867.3 Welding Procedure Specification for Electron Beam Welding (GB/T 19867.3-2008, ISO 15609-3:2004, IDT) GB/T 19867.4 Welding Procedure Specification for Laser Beam Welding (GB/T 19867.4-2008, ISO 15609-4:2004, IDT) GB/T 19868.1 Welding procedure qualification based on tested welding consumables (GB/T 19868.1-2005, ISO 15610:2003, IDT) GB/T 19868.2 Welding procedure qualification based on previous welding experience (GB/T 19868.2-2005, ISO 15611:2003, IDT) GB/T 19868.3 Welding procedure qualification by adoption of a standard welding procedure (GB/T 19868.3-2005, ISO 15612:2004, IDT) GB/T 19868.4 Welding Procedure Qualification Based on Pre-production Welding Test (GB/T 19868.4-2005, ISO 15613:2004, IDT) GB/T 19869.1 Welding procedure qualification test for steels, nickel and nickel alloys (GB/T 19869.1-2005, ISO 15614-1:2004, IDT) ISO 9606-2 Qualification test of welders-Fusion welding-Part 2: Aluminium and aluminium alloys ISO 9606-3 Approval testing of welders-Fusion welding-Part 3: Copper and copper alloys ISO 9606-4 Approval testing of welders-Fusion welding-Part 4: Nickel and nickel alloys ISO 9606-5 Approval testing of welders-Fusion welding-Part 5: Titanium and titanium alloys, zirconium and zirconium alloys ISO 14555 Welding-Arc stud welding of metallic materials ISO 15614-2 Specification and qualification of welding procedures for metallic materials-Welding procedure test-Part 2: Arc welding of aluminium and its alloys ISO 15614-3 Specification and qualification of welding procedures for metallic materials-Welding procedure test-Part 3: Fusion and pressure welding of non-alloyed and low-alloyed cast irons ISO 15614-4 Specification and qualification of welding procedures for metallic materials-Welding procedure test Part 4: Finishing welding of aluminium castings ISO 15614-5 Specification and qualification of welding procedures for metallic materials-Welding procedure test-Part 5: Arc welding of titanium, zirconium and their alloys ISO 15614-6 Specification and qualification of welding procedures for metallic materials-Welding procedure test-Part 6: Arc welding of copper and copper alloys ISO 15614-7 Specification and qualification of welding procedures for metallic materials-Welding procedure test-Part 7: Overlay welding ISO 15614-8 Specification and qualification of welding procedures for metallic materials-Welding procedure test-Part 8: Welding of tubes to tube-plate joints ISO 15614-10 Specification and qualification of welding procedures for metallic materials-Welding procedure test-Part 10: Hyperbaric dry welding ISO 15614-11 Specification and qualification of welding procedures for metallic materials-Welding procedure test-Part 11: Electron and laser beam welding ISO 15618-1 Qualification testing of welders for underwater welding-Part 1: Diver-welders for hyperbaric wet welding ISO 15618-2 Qualification testing of welders for underwater welding--Part 2: Diver-welders and welding operators for hyperbaric dry welding ISO 17635 Non-destructive testing of welds-General rules for fusion welds in metallic materials ISO 17636 Non-destructive testing of welds-Radiographic testing of fusion-welded joints ISO 17637 Non-destructive testing of welds-Visual testing of fusion-welded joints ISO 17638 Non-destructive testing of welds-Magnetic particle testing ISO 17639 Destructive tests on welds in metallic materials-Macroscopic and microscopic examination of welds ISO 17640 Non-destructive testing of welds-Ultrasonic testing of welded joints ISO 17662 Welding-Calibration, verification and validation of equipment used for welding, including ancillary activities ISO/TR 17663 Welding-Guidelines for quality requirements for heat treatment in connection with welding and allied processes ISO/TR 17671-2 Welding-Recommendations for welding of metallic materials-Part 2: Arc welding of ferritic steels ISO/TR 17844 Comparison of standardized methods for the avoidance of cold cracks 2.3 Applicability of standards Among the activities in relation to welding quality control, the key processes (or elements) which have significant impacts on the welding quality shall be specially controlled. ——These control activities shall comply with the standards listed in Table 1 ~ Table 9. ——The standards with which the quality control for stud welding is required to comply is listed in Table 10. Note 1: The quality requirements for fusion welding may also be used for friction welding, as appropriate (see ISO 15620). Note 2: For qualification/education scheme for personnel dealing with welding coordination and inspection, see Annex A.

Contents of GB/T 12467.5-2009