GB/T 12618.2-2006 Open End Blind Rivets with Break Pull Mandrel and Protruding Head-Property Class 30
1 Scope
This part specifies the mechanical properties and application data of Open end blind rivets with break pull mandrel and protruding head-property class 30 with the rivet body diameter d=2.4 mm~6.4 mm, the rivet body material of aluminum alloy (AlA) and the rivet core material of steel (St).
2 Normative References
The following normative documents contain provisions which, through reference in this Part of GB/T 12618, constitute provisions of this part. For dated reference, subsequent amendments to, or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this Part are encouraged to study whether the latest editions of these documents are applicable. For undated references, the latest edition of the normative document referred to applies.
GB/T 90.1 Fasteners - Acceptance inspection (GB/T 90.1-2002, idt ISO 3269: 2000)
GB/T 90.2 Fasteners--Marking and packaging
GB/T 699 Quality carbon structural steels
GB/T 1237 Designation system for fasteners (GB/T 1237-2000, eqv ISO 8991: 1986)
GB/T 3098.18 Mechanical properties of fasteners--Blind rivets testing (GB/T 3098.18-2004, ISO 14589: 2000, Blind rivets-Mechanical testing, IDT)
GB/T 3098.19 Mechanical properties of fasteners-Blind rivets with break pull mandrel
GB/T 3099.2 Terminology of fasteners-Blind rivets (GB/T 3099.2-2004, ISO 14588: 2000, Blind rivets- Terminology and definitions, IDT)
GB/T 3206 Carbon constructional quality steel wires
GB/T 5267.1 Fasteners - Electroplated coatings (GB/T 5267.1-2002, idt ISO 4042: 1999 IDT)
GB/T 9800 Chromate conversion coatings on electroplated zinc and cadmium coatings (GB/T 9800-1988, eqv ISO 4520: 1981)
3 Dimension
3.1 General provisions
Dimension code and marks shall meet those specified in GB/T 3099.2.
3.2 Rivet dimension
Foreword II
1 Scope
2 Normative References
3 Dimension
3.1 General provisions
3.2 Rivet dimension
3.3 Rivet hole diameter
4 Material Combinations and Surface Treatment
5 Mechanical Properties
5.1 Shear load, tensile load and rivet core breaking load
5.2 Rivet core dismantlement ability
5.3 Rivet head holding capacity
6 Performance Quality
7 Acceptance Inspection, Marking and Packaging
8 Designation
Annex A
GB/T 12618.2-2006 Open End Blind Rivets with Break Pull Mandrel and Protruding Head-Property Class 30
1 Scope
This part specifies the mechanical properties and application data of Open end blind rivets with break pull mandrel and protruding head-property class 30 with the rivet body diameter d=2.4 mm~6.4 mm, the rivet body material of aluminum alloy (AlA) and the rivet core material of steel (St).
2 Normative References
The following normative documents contain provisions which, through reference in this Part of GB/T 12618, constitute provisions of this part. For dated reference, subsequent amendments to, or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this Part are encouraged to study whether the latest editions of these documents are applicable. For undated references, the latest edition of the normative document referred to applies.
GB/T 90.1 Fasteners - Acceptance inspection (GB/T 90.1-2002, idt ISO 3269: 2000)
GB/T 90.2 Fasteners--Marking and packaging
GB/T 699 Quality carbon structural steels
GB/T 1237 Designation system for fasteners (GB/T 1237-2000, eqv ISO 8991: 1986)
GB/T 3098.18 Mechanical properties of fasteners--Blind rivets testing (GB/T 3098.18-2004, ISO 14589: 2000, Blind rivets-Mechanical testing, IDT)
GB/T 3098.19 Mechanical properties of fasteners-Blind rivets with break pull mandrel
GB/T 3099.2 Terminology of fasteners-Blind rivets (GB/T 3099.2-2004, ISO 14588: 2000, Blind rivets- Terminology and definitions, IDT)
GB/T 3206 Carbon constructional quality steel wires
GB/T 5267.1 Fasteners - Electroplated coatings (GB/T 5267.1-2002, idt ISO 4042: 1999 IDT)
GB/T 9800 Chromate conversion coatings on electroplated zinc and cadmium coatings (GB/T 9800-1988, eqv ISO 4520: 1981)
3 Dimension
3.1 General provisions
Dimension code and marks shall meet those specified in GB/T 3099.2.
3.2 Rivet dimension
Contents of GB/T 12618.2-2006
Foreword II
1 Scope
2 Normative References
3 Dimension
3.1 General provisions
3.2 Rivet dimension
3.3 Rivet hole diameter
4 Material Combinations and Surface Treatment
5 Mechanical Properties
5.1 Shear load, tensile load and rivet core breaking load
5.2 Rivet core dismantlement ability
5.3 Rivet head holding capacity
6 Performance Quality
7 Acceptance Inspection, Marking and Packaging
8 Designation
Annex A
