GB/T 18029.6-2024 Wheelchairs - Part 6: Determination of maximum speed of electrically powered wheelchairs
1 Scope
This document specifies test methods for determining the maximum speed of electrically powered wheelchairs, including scooters, intended to carry one person with a maximum nominal speed not exceeding 15 km/h on a level surface.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 7176-11 Wheelchairs - Part 11: Test dummies
Note: GB/Z 18029.11-2021, Wheelchairs - Part 11: Test dummies (ISO 7176-11:2012, IDT)
ISO 7176-13 Wheelchair - Part 13: Determination of friction of test surface
Note: GB/T 18029.13-2008, Wheelchair - Part 13: Determination of friction of test surface (ISO 7176-13:1989, IDT)
ISO 7176-15 Wheelchairs - Part 15: Requirements for information disclosure, documentation and labelling
Note: GB/T 18029.15-2008, Wheelchairs - Part 15: Requirements for information disclosure, documentation and labelling (ISO 7176-15:1996, IDT)
ISO 7176-22 Wheelchairs - Part 22: Set-up procedures
Note: GB/T 18029.22-2024, Wheelchairs - Part 22: Set-up procedures (ISO 7176-22:2014, IDT)
3 Terms and definitions
No terms and definitions are listed in this document.
4 Apparatus
4.1 Instrumentation
That may need to be added to the test dummy, in which case its mass shall not exceed 5 % of the total dummy mass.
4.2 Horizontal test plane
Made up of a rigid, flat, horizontal surface of sufficient size to conduct the tests and with a coefficient of friction that meets the requirements of ISO 7176-13.
Note: The floor of a typical large building used for manufacturing or indoor leisure with, for example, a concrete, asphalt or wooden floor is acceptable.
4.3 Speed measurement device
To measure and record speed up to 5 m/s with an accuracy of ± 0.1 m/s and a sample rate of at least 60 Hz.
4.4 Test dummy
As specified in ISO 7176-11, or a human test occupant according to ISO 7176-22.
Mass added to the wheelchair for the purposes of control or instrumentation should not significantly affect the overall mass distribution of the wheelchair. The overall mass of the loaded wheelchair shall be adjusted to compensate for any such added mass.
4.5 Supplementary weight
Shall be added to a human test driver to give the mass distribution equivalent to the relevant dummy.
Standard
GB/T 18029.6-2024 Wheelchairs—Part 6: Determination of maximum speed of electrically powered wheelchairs (English Version)
Standard No.
GB/T 18029.6-2024
Status
valid
Language
English
File Format
PDF
Word Count
7000 words
Price(USD)
210.0
Implemented on
2024-12-1
Delivery
via email in 1~3 business day
Detail of GB/T 18029.6-2024
Standard No.
GB/T 18029.6-2024
English Name
Wheelchairs—Part 6: Determination of maximum speed of electrically powered wheelchairs
GB/T 18029.6-2024 Wheelchairs - Part 6: Determination of maximum speed of electrically powered wheelchairs
1 Scope
This document specifies test methods for determining the maximum speed of electrically powered wheelchairs, including scooters, intended to carry one person with a maximum nominal speed not exceeding 15 km/h on a level surface.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 7176-11 Wheelchairs - Part 11: Test dummies
Note: GB/Z 18029.11-2021, Wheelchairs - Part 11: Test dummies (ISO 7176-11:2012, IDT)
ISO 7176-13 Wheelchair - Part 13: Determination of friction of test surface
Note: GB/T 18029.13-2008, Wheelchair - Part 13: Determination of friction of test surface (ISO 7176-13:1989, IDT)
ISO 7176-15 Wheelchairs - Part 15: Requirements for information disclosure, documentation and labelling
Note: GB/T 18029.15-2008, Wheelchairs - Part 15: Requirements for information disclosure, documentation and labelling (ISO 7176-15:1996, IDT)
ISO 7176-22 Wheelchairs - Part 22: Set-up procedures
Note: GB/T 18029.22-2024, Wheelchairs - Part 22: Set-up procedures (ISO 7176-22:2014, IDT)
3 Terms and definitions
No terms and definitions are listed in this document.
4 Apparatus
4.1 Instrumentation
That may need to be added to the test dummy, in which case its mass shall not exceed 5 % of the total dummy mass.
4.2 Horizontal test plane
Made up of a rigid, flat, horizontal surface of sufficient size to conduct the tests and with a coefficient of friction that meets the requirements of ISO 7176-13.
Note: The floor of a typical large building used for manufacturing or indoor leisure with, for example, a concrete, asphalt or wooden floor is acceptable.
4.3 Speed measurement device
To measure and record speed up to 5 m/s with an accuracy of ± 0.1 m/s and a sample rate of at least 60 Hz.
4.4 Test dummy
As specified in ISO 7176-11, or a human test occupant according to ISO 7176-22.
Mass added to the wheelchair for the purposes of control or instrumentation should not significantly affect the overall mass distribution of the wheelchair. The overall mass of the loaded wheelchair shall be adjusted to compensate for any such added mass.
4.5 Supplementary weight
Shall be added to a human test driver to give the mass distribution equivalent to the relevant dummy.
