Detail of GB/T 24632.2-2024

Introduction of GB/T 24632.2-2024

GB/T 24632.2-2024 Geometrical product specifications (GPS) - Cylindricity - Part 2 : Specification operators 1 Scope This standard specifies the complete specification operator for cylindricity of complete integral features. This standard is applicable to the cylindricity of complete integral features. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 12180-1 Geometrical product specifications (GPS) - Cylindricity - Part 1 : Vocabulary and parameters of cylindrical form Note: GB/T 24633.1-2024 Geometrical product specifications (GPS) - Cylindricity - Part 1 : Vocabulary and parameters of cylindrical form (ISO 12180-1:2011, MOD) ISO 12181-1 Geometrical product specifications (GPS) - Roundness - Part 1 : Vocabulary and parameters of roundness Note: GB/T 24632.1-2024 Geometrical product specifications (GPS) - Roundness - Part 1 : Vocabulary and parameters of roundness (ISO 12181-1:2011, MOD) ISO 12780-1 Geometrical product specifications (GPS) - Straightness - Part 1 : Vocabulary and parameters of straightness Note: GB/T 24631.1-2024 Geometrical product specifications (GPS) - Straightness - Part 1 : Vocabulary and parameters of straightness (ISO 12780-1:2011, MOD) ISO 14253-1 Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 1 : Decision rules for verifying conformity or nonconformity with specifications Note: GB/T 18779.1-2022 Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 1 : Decision rules for verifying conformity or nonconformity with specifications (ISO 14253-1:2017, IDT) ISO 16610-21 Geometrical product specifications (GPS) - Filtration - Part 21 : Linear profile filters : Gaussian filters Note: GB/T 26958.21-2020 Geometrical product specifications (GPS) - Filtration - Part 21 : Linear profile filters : Gaussian filters (ISO 16610-21:2011, IDT) ISO 17450-2 Geometrical product specifications (GPS) - General concepts - Part 2 : Basic tenets, specifications, operators, uncertainties and ambiguities Note: GB/T 24637.2-2020 Geometrical product specifications (GPS) - General concepts - Part 2 : Basic tenets, specifications, operators, uncertainties and ambiguities 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 12180-1, ISO 12181-1, ISO 12780-1, ISO 16610-21 and ISO 17450-2 apply. 4 Complete specification operator 4.1 General The complete specification operator (as defined in ISO 17450-2) is a full ordered set of unambiguous specification operations in a well-defined order. The complete specification operator defines the transmission band for the cylindricity surface, together with an appropriate stylus tip geometry. Note: In practice, it is unrealistic to hope to achieve comprehensive coverage of the cylindrical feature given by the theoretical minimum density of points (see Annex B) within an acceptable time span using available technology. Therefore, more limited extraction strategies are employed that give specific, rather than general, information concerning the deviations from cylindrical form. 4.2 Probing system 4.2.1 Probing method A contacting probing system with a stylus tip, as defined in 4.2.2, is part of the specification operator. 4.2.2 Stylus tip geometry The theoretically exact stylus tip geometry is a sphere. 4.2.3 Probing force The probing force is 0 N. 5 Compliance with the specification For proving conformance or non-conformance with the specification, ISO 14253-1 applies.

Contents of GB/T 24632.2-2024