GB/T 45788.1-2025 Quality requirements for resistance welding of metallic - Part 1: Comprehensive quality requirements
1 Scope
This document specifies the comprehensive quality requirements for resistance welding of metallic, including contract and technical review, sub-contracting, personnel, equipment, welding and related activities, welding electrodes and auxiliaries, storage of parent metal, heat treatment, tests and inspections related to welding, non-conformances and corrective actions, equipment calibration, identification and quality reporting, etc.
This document is applicable to the comprehensive quality requirements for welding both in metal material workshops and on site. Annex A presents a comparison table of the comprehensive quality requirements and elementary quality requirements for resistance welding of metallic.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 12467.1 Quality requirements for fusion welding of metallic materials - Part 1: Criteria for the selection of the appropriate level of quality requirements (GB/T 12467.1-2009; ISO 3834-1:2005, IDT)
3 Terms and definitions
For the purpose of this document, the terms and definitions given in GB/T 12467.1 apply.
4 Contract and technical review
4.1 General
The manufacturer shall review the contractual requirements and the design scheme provided by the user or in-house data for construction designed by the manufacturer. This is to ensure that all information necessary to carry out the fabrication operations is complete and feasible prior to the commencement of the work. The manufacturer shall affirm his capability to meet all welding contract requirements and ensure adequate planning of all quality-related activities.
Contract review is performed by the manufacturer to verify that:
——the contract is within his capability to carry out;
——documentation is clear, correct and unambiguous;
——and sufficient resources are available to achieve delivery schedules;
The manufacturer should ensure any variations between the contract and previous tender documentation are identified and the user notified of any programme, cost or engineering changes that may result.
Contents
Foreword i
Introduction iii
1 Scope
2 Normative references
3 Terms and definitions
4 Contract and technical review
4.1 General
4.2 Contract review
4.3 Technical review
5 Sub-contracting
6 Welding personnel
6.1 General
6.2 Operators
6.3 Resistance weld setter
6.4 Welding responsible personnel
7 Testing and examination personnel
8 Equipment
8.1 Production and testing facilities
8.2 Description of facilities
8.3 Approval of facilities
8.4 New facilities
8.5 Maintenance
9 Welding and related activities
9.1 Production planning
9.2 Welding procedure specification
9.3 Welding procedure approval
9.4 Work instructions
9.5 Procedures for document preparation and control
10 Welding electrodes and auxiliaries
10.1 General
10.2 Batch testing
10.3 Welding electrodes
10.4 Marking of welding electrodes
11 Storage of parent metal
12 Heat treatment
13 Weld-related inspection and testing
13.1 General
13.2 Inspection before welding
13.3 Inspection and testing during production
13.4 Inspection and testing after welding
13.5 Inspection and test status
14 Non-conformance and corrective actions
15 Calibration of equipment
16 Identification and traceability
17 Quality records
Annex A (informative) Summary comparison of quality requirements for resistance welding of metallic
GB/T 45788.1-2025 Quality requirements for resistance welding of metallic - Part 1: Comprehensive quality requirements
1 Scope
This document specifies the comprehensive quality requirements for resistance welding of metallic, including contract and technical review, sub-contracting, personnel, equipment, welding and related activities, welding electrodes and auxiliaries, storage of parent metal, heat treatment, tests and inspections related to welding, non-conformances and corrective actions, equipment calibration, identification and quality reporting, etc.
This document is applicable to the comprehensive quality requirements for welding both in metal material workshops and on site. Annex A presents a comparison table of the comprehensive quality requirements and elementary quality requirements for resistance welding of metallic.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 12467.1 Quality requirements for fusion welding of metallic materials - Part 1: Criteria for the selection of the appropriate level of quality requirements (GB/T 12467.1-2009; ISO 3834-1:2005, IDT)
3 Terms and definitions
For the purpose of this document, the terms and definitions given in GB/T 12467.1 apply.
4 Contract and technical review
4.1 General
The manufacturer shall review the contractual requirements and the design scheme provided by the user or in-house data for construction designed by the manufacturer. This is to ensure that all information necessary to carry out the fabrication operations is complete and feasible prior to the commencement of the work. The manufacturer shall affirm his capability to meet all welding contract requirements and ensure adequate planning of all quality-related activities.
Contract review is performed by the manufacturer to verify that:
——the contract is within his capability to carry out;
——documentation is clear, correct and unambiguous;
——and sufficient resources are available to achieve delivery schedules;
The manufacturer should ensure any variations between the contract and previous tender documentation are identified and the user notified of any programme, cost or engineering changes that may result.
Contents of GB/T 45788.1-2025
Contents
Foreword i
Introduction iii
1 Scope
2 Normative references
3 Terms and definitions
4 Contract and technical review
4.1 General
4.2 Contract review
4.3 Technical review
5 Sub-contracting
6 Welding personnel
6.1 General
6.2 Operators
6.3 Resistance weld setter
6.4 Welding responsible personnel
7 Testing and examination personnel
8 Equipment
8.1 Production and testing facilities
8.2 Description of facilities
8.3 Approval of facilities
8.4 New facilities
8.5 Maintenance
9 Welding and related activities
9.1 Production planning
9.2 Welding procedure specification
9.3 Welding procedure approval
9.4 Work instructions
9.5 Procedures for document preparation and control
10 Welding electrodes and auxiliaries
10.1 General
10.2 Batch testing
10.3 Welding electrodes
10.4 Marking of welding electrodes
11 Storage of parent metal
12 Heat treatment
13 Weld-related inspection and testing
13.1 General
13.2 Inspection before welding
13.3 Inspection and testing during production
13.4 Inspection and testing after welding
13.5 Inspection and test status
14 Non-conformance and corrective actions
15 Calibration of equipment
16 Identification and traceability
17 Quality records
Annex A (informative) Summary comparison of quality requirements for resistance welding of metallic
