1 Scope
This part specifies the weld studs for manual welding with thread specifications of M3~M20.
2 Normative references
The following normative documents contain provisions which, through reference in this part, constitute provisions of this part. For dated references, subsequent amendments (excluding corrections), or revisions, of any of these publications do not apply. However, parties to agreements based on this part are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest editions apply to this part.
GB/T 2 Fasteners - Ends of parts with external thread (GB/T 2-2001, idt ISO 4753: 1999)
GB/T 90.1 Fasteners - Acceptance inspection (GB/T 90.1-2002, idt ISO 3269: 2000)
GB/T 90.2-2002 Fasteners - Marking and packaging
GB/T 196 General purpose metric screw threads - Basic dimensions (GB/T 196-2003, ISO 724: 1993, ISO general purpose metric screw threads - Basic dimensions, MOD)
GB/T 197 General purpose metric screw threads - Tolerances (GB/T 197-2003, ISO 965-1: 1998, ISO general purpose metric screw threads - Tolerances - Part 1: Principles and basic data, MOD)
GB/T 1237 Designation system for fasteners (GB/T 1237-2000, eqv ISO 8991:1986)
GB/T 3098.1 Mechanical properties of fasteners - Bolts, screws and studs (GB/T 3098.1-2010, idt ISO 898-1: 1999)
GB/T 5267.1 Fasteners - Electroplated coatings (GB/T 5267.1-2002, idt ISO 4042: 1999)
GB/T 16938 Fasteners - General requirements for bolts, screws, studs and nuts (GB/T 16938-2008, ISO 8839: 2005, IDT)
3 Dimensions
See Figure 1 and Table 1 for the types and dimensions of weld studs for manual welding.
Foreword i
1 Scope
2 Normative references
3 Dimensions
4 Technical requirements and reference standards
5 Marking
1 Scope
This part specifies the weld studs for manual welding with thread specifications of M3~M20.
2 Normative references
The following normative documents contain provisions which, through reference in this part, constitute provisions of this part. For dated references, subsequent amendments (excluding corrections), or revisions, of any of these publications do not apply. However, parties to agreements based on this part are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest editions apply to this part.
GB/T 2 Fasteners - Ends of parts with external thread (GB/T 2-2001, idt ISO 4753: 1999)
GB/T 90.1 Fasteners - Acceptance inspection (GB/T 90.1-2002, idt ISO 3269: 2000)
GB/T 90.2-2002 Fasteners - Marking and packaging
GB/T 196 General purpose metric screw threads - Basic dimensions (GB/T 196-2003, ISO 724: 1993, ISO general purpose metric screw threads - Basic dimensions, MOD)
GB/T 197 General purpose metric screw threads - Tolerances (GB/T 197-2003, ISO 965-1: 1998, ISO general purpose metric screw threads - Tolerances - Part 1: Principles and basic data, MOD)
GB/T 1237 Designation system for fasteners (GB/T 1237-2000, eqv ISO 8991:1986)
GB/T 3098.1 Mechanical properties of fasteners - Bolts, screws and studs (GB/T 3098.1-2010, idt ISO 898-1: 1999)
GB/T 5267.1 Fasteners - Electroplated coatings (GB/T 5267.1-2002, idt ISO 4042: 1999)
GB/T 16938 Fasteners - General requirements for bolts, screws, studs and nuts (GB/T 16938-2008, ISO 8839: 2005, IDT)
3 Dimensions
See Figure 1 and Table 1 for the types and dimensions of weld studs for manual welding.
Contents of GB/T 902.1-2008
Foreword i
1 Scope
2 Normative references
3 Dimensions
4 Technical requirements and reference standards
5 Marking
