1 Scope
This standard specifies technical requirements, test methods, inspection rules, packaging, labeling, product data sheet, transportation and storage requirements for aircraft disinfectants (the “disinfectant”).
This standard applies to liquid disinfection products for aircrafts.
2 Normative references
The following documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding any corrigendum), or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For any undated references, the latest edition of the document referred to applies.
GB/T 2828.1 Sampling procedures for inspection by attributes—Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection (GB/T 2828.1- 2003, ISO 2859-1:1999, IDT)
GB 16483 General rules for preparation of chemical safety data sheet (GB 16483-2000, eqv. ISO 11014-1: 1994)
ASTM D 93 Standard test methods for flash point by Pensky-Martens closed cup tester
ASTM D 471 Standard test method for rubber property—Effect of liquids
ASTM F 483 Standard practice for total immersion corrosion test for aircraft maintenance chemicals
ASTM F 484 Standard test method for stress crazing of acrylic plastics in contact with liquid or semi-liquid compounds
ASTM F 502 Standard test method for effects of cleaning and chemical maintenance materials on painted aircraft surfaces
ASTM F 1104 Standard test method for preparing aircraft cleaning compounds, liquid type, water base, for storage stability testing
ASTM F 1110 Standard test method for sandwich corrosion test
ASTM F 2109 Standard test method to determine color change and staining caused by aircraft maintenance chemicals upon aircraft cabin interior hard surfaces
3 Technical requirements
3.1 General
Composition of the disinfectant shall be optional with the manufacture. The disinfectant shall be licensed by the competent health authority of China and meet the requirements of this standard.
3.2 Appearance
The disinfectant shall be uniform and consistent in color, free from surface crusts, agglomerates, and impurities that affect product use.
3.3 Flash point
The flash point of the disinfectant shall not be lower than 100 °C.
3.4 Storage stability
The disinfectant shall show no precipitation, layering, or increased turbidity after storage stability testing.
Foreword i
1 Scope
2 Normative references
3 Technical requirements
4 Test methods
5 Inspection rules
6 Packaging, labeling, product data sheet, transportation and storage
1 Scope
This standard specifies technical requirements, test methods, inspection rules, packaging, labeling, product data sheet, transportation and storage requirements for aircraft disinfectants (the “disinfectant”).
This standard applies to liquid disinfection products for aircrafts.
2 Normative references
The following documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding any corrigendum), or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For any undated references, the latest edition of the document referred to applies.
GB/T 2828.1 Sampling procedures for inspection by attributes—Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection (GB/T 2828.1- 2003, ISO 2859-1:1999, IDT)
GB 16483 General rules for preparation of chemical safety data sheet (GB 16483-2000, eqv. ISO 11014-1: 1994)
ASTM D 93 Standard test methods for flash point by Pensky-Martens closed cup tester
ASTM D 471 Standard test method for rubber property—Effect of liquids
ASTM F 483 Standard practice for total immersion corrosion test for aircraft maintenance chemicals
ASTM F 484 Standard test method for stress crazing of acrylic plastics in contact with liquid or semi-liquid compounds
ASTM F 502 Standard test method for effects of cleaning and chemical maintenance materials on painted aircraft surfaces
ASTM F 1104 Standard test method for preparing aircraft cleaning compounds, liquid type, water base, for storage stability testing
ASTM F 1110 Standard test method for sandwich corrosion test
ASTM F 2109 Standard test method to determine color change and staining caused by aircraft maintenance chemicals upon aircraft cabin interior hard surfaces
3 Technical requirements
3.1 General
Composition of the disinfectant shall be optional with the manufacture. The disinfectant shall be licensed by the competent health authority of China and meet the requirements of this standard.
3.2 Appearance
The disinfectant shall be uniform and consistent in color, free from surface crusts, agglomerates, and impurities that affect product use.
3.3 Flash point
The flash point of the disinfectant shall not be lower than 100 °C.
3.4 Storage stability
The disinfectant shall show no precipitation, layering, or increased turbidity after storage stability testing.
Contents of MH/T 6045-2008
Foreword i
1 Scope
2 Normative references
3 Technical requirements
4 Test methods
5 Inspection rules
6 Packaging, labeling, product data sheet, transportation and storage
