Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
NB/T 47065-2018 consists of the following five parts under the general title Vessel support:
——Part 1: Saddle support (NB/T 47065.1-2018);
——Part 2: Leg support (NB/T 47065.2-2018);
——Part 3: Lug support (NB/T 47065.3-2018);
——Part 4: Bracket support (NB/T 47065.4-2018);
——Part 5: Support lugs with rigid rings (NB/T 47065.5-2018).
This is Part 4 of NB/T 47065-2018: Bracket support.
This part is developed in accordance with the rules given in GB/T 1.1-2009 Directives for standardization - Part 1: Structure and drafting of standards.
This part replaces JB/T 4712.4-2007 Vessel support - Part 4: Bracket support. The following main technical changes have been made with respect to JB/T 4712.4-2007:
——Main material of bracket support: Q235B plate and 10# steel pipe; the allowable material stress of the bracket support body is [σ]=200MPa and 180MPa respectively;
——The allowable load [F] of Type B support limited by the head is given when the allowable stress [σ] of equipment head material of Type B support is 120MPa, 140MPa, 167MPa or 185MPa;
——The load superposition requirements for pipeline thrust and vertical seismic force are added;
——The applicable thickness range of the head is 6mm~24mm.
This part was proposed by and is under the jurisdiction of the National Technical Committee on Boilers and Pressure Vessels of Standardization Administration of China (SAC/TC 262).
This part is drafted by the Design Branch National Technical Committee on Boilers and Pressure Vessels of Standardization Administration of China.
This part is interpreted by the National Technical Committee on Boilers and Pressure Vessels of Standardization Administration of China (SAC/TC 262).
The previous editions of this part are as follows:
——JB/T 4724-1992;
——JB/T 4712.4-2007.
Vessel supports - Part 4: Bracket support
1 Scope
1.1 This part specifies the type characteristics, series parameters and dimensions, materials, marking, manufacturing technical requirements and selection instructions of bracket support.
1.2 It is applicable to steel vertical cylindrical vessels under the following conditions:
a) nominal diameter: DN800mm ~ DN4 000mm;
b) the ratio (L/DN) of cylinder length L to nominal diameter DN is not greater than 5;
c) the total height H0 of the vessel is not greater than 10m;
d) the allowable service temperature is -20℃~200℃.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 985.1 Recommended joint preparation for gas welding, manual metal arc welding, gas-shield arc welding and beam welding
GB/T 1804 General tolerances - Tolerances for linear and angular dimensions without individual tolerance indications
3 Type characteristics
See Table 1 for the type characteristics of bracket support.
Table 1 Type characteristics
Type Support No. Backing plate Applicable nominal diameter DN/mm Support dimension (see the tables and figures)
Steel plate welding A 1~4 With 800~2 200 Figure 1 and Table 2
5~6 2 400~3 000 Figure 2 and Table 2
Steel pipe production B 1~8 With 800~4 000 Figure 3 and Table 3
4 Series parameters and dimensions
4.1 The structure and dimension of Type A support shall be as specified in Figure 1, Figure 2 and Table 2, and those of Type B support shall be as specified in Figure 3 and Table 3.
4.2 The thickness of the support backing plate may be adjusted according to actual needs. The height of Type B support may be changed, but it shall not be greater than the upper limit of support height.
Figure 1 No. 1 ~ No. 4 Type A bracket support
Figure 2 No. 5 ~ No. 6 Type A bracket support
Figure 3 No. 1 ~ No. 8 Type B bracket support
Foreword i
1 Scope
2 Normative references
3 Type characteristics
4 Series parameters and dimensions
5 Materials
6 Marking
7 Technical requirements of production
8 Selection methods
Annex A (Informative) Approximate calculation of actual load borne on bracket support
Annex B (Informative) Allowable vertical load [F] of Type B support limited by vessel head
Annex C (Informative) Installation height of bracket support
NB/T 47065.4-2018, NB 47065.4-2018, NBT 47065.4-2018, NB/T47065.4-2018, NB/T 47065.4, NB/T47065.4, NB47065.4-2018, NB 47065.4, NB47065.4, NBT47065.4-2018, NBT 47065.4, NBT47065.4
Introduction of NB/T 47065.4-2018
Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
NB/T 47065-2018 consists of the following five parts under the general title Vessel support:
——Part 1: Saddle support (NB/T 47065.1-2018);
——Part 2: Leg support (NB/T 47065.2-2018);
——Part 3: Lug support (NB/T 47065.3-2018);
——Part 4: Bracket support (NB/T 47065.4-2018);
——Part 5: Support lugs with rigid rings (NB/T 47065.5-2018).
This is Part 4 of NB/T 47065-2018: Bracket support.
This part is developed in accordance with the rules given in GB/T 1.1-2009 Directives for standardization - Part 1: Structure and drafting of standards.
This part replaces JB/T 4712.4-2007 Vessel support - Part 4: Bracket support. The following main technical changes have been made with respect to JB/T 4712.4-2007:
——Main material of bracket support: Q235B plate and 10# steel pipe; the allowable material stress of the bracket support body is [σ]=200MPa and 180MPa respectively;
——The allowable load [F] of Type B support limited by the head is given when the allowable stress [σ] of equipment head material of Type B support is 120MPa, 140MPa, 167MPa or 185MPa;
——The load superposition requirements for pipeline thrust and vertical seismic force are added;
——The applicable thickness range of the head is 6mm~24mm.
This part was proposed by and is under the jurisdiction of the National Technical Committee on Boilers and Pressure Vessels of Standardization Administration of China (SAC/TC 262).
This part is drafted by the Design Branch National Technical Committee on Boilers and Pressure Vessels of Standardization Administration of China.
This part is interpreted by the National Technical Committee on Boilers and Pressure Vessels of Standardization Administration of China (SAC/TC 262).
The previous editions of this part are as follows:
——JB/T 4724-1992;
——JB/T 4712.4-2007.
Vessel supports - Part 4: Bracket support
1 Scope
1.1 This part specifies the type characteristics, series parameters and dimensions, materials, marking, manufacturing technical requirements and selection instructions of bracket support.
1.2 It is applicable to steel vertical cylindrical vessels under the following conditions:
a) nominal diameter: DN800mm ~ DN4 000mm;
b) the ratio (L/DN) of cylinder length L to nominal diameter DN is not greater than 5;
c) the total height H0 of the vessel is not greater than 10m;
d) the allowable service temperature is -20℃~200℃.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 985.1 Recommended joint preparation for gas welding, manual metal arc welding, gas-shield arc welding and beam welding
GB/T 1804 General tolerances - Tolerances for linear and angular dimensions without individual tolerance indications
3 Type characteristics
See Table 1 for the type characteristics of bracket support.
Table 1 Type characteristics
Type Support No. Backing plate Applicable nominal diameter DN/mm Support dimension (see the tables and figures)
Steel plate welding A 1~4 With 800~2 200 Figure 1 and Table 2
5~6 2 400~3 000 Figure 2 and Table 2
Steel pipe production B 1~8 With 800~4 000 Figure 3 and Table 3
4 Series parameters and dimensions
4.1 The structure and dimension of Type A support shall be as specified in Figure 1, Figure 2 and Table 2, and those of Type B support shall be as specified in Figure 3 and Table 3.
4.2 The thickness of the support backing plate may be adjusted according to actual needs. The height of Type B support may be changed, but it shall not be greater than the upper limit of support height.
Figure 1 No. 1 ~ No. 4 Type A bracket support
Figure 2 No. 5 ~ No. 6 Type A bracket support
Figure 3 No. 1 ~ No. 8 Type B bracket support
Contents of NB/T 47065.4-2018
Foreword i
1 Scope
2 Normative references
3 Type characteristics
4 Series parameters and dimensions
5 Materials
6 Marking
7 Technical requirements of production
8 Selection methods
Annex A (Informative) Approximate calculation of actual load borne on bracket support
Annex B (Informative) Allowable vertical load [F] of Type B support limited by vessel head
Annex C (Informative) Installation height of bracket support
