1.1 This standard specifies the construction procedures and methods of spherical tanks, as well as the requirements of field assembly welding procedure control, test/inspection/quality specifications and handover specifications.
1.2 This standard is applicable to the construction of orange-segment-model or mixed-model, pillar-supported, carbon steel/low alloy steel-welded spherical tanks (see Annex A) whose design pressure is larger than or equal to 0.1MPa but not larger than 4MPa, and whose nominal volume is larger than or equal to 50m3.
1.3 This standard is applicable to the following construction scopes of spherical tanks (see Article 1.1):
a）Spherical shell plate and its welding joint;
b）Pressure head, flat cover and fastener of spherical tank opening;
c）The following parts where the spherical shell pipes are connected with outside pipe:
1) The first girth joint groove head face of welded connection;
2) The first screwed joint head face of screwed connection;
3) The first flange sealing surface of flanged connection;
d） Non-pressure elements and their connection welds of the spherical tanks such as pillar, pull rod, backing plate and base plate.
1.4 This standard is not applicable to construction of the following spherical tanks:a）Spherical tanks suffering from nuclear radiation;
b）Non-fixed (such as vehicle or ship-borne) spherical tanks;
c）Spherical tanks with double-shell structures;
d）Spherical tanks formed by expansion.
Foreword III 1 Scope 2 Normative References 3 General Provisions 4 Construction Preparations 4.1 Technical Preparation 4.2 Construction Field Preparation 4.3 Equipment Preparation 5 Acceptances of Spherical Shell Plates and Spare Parts 5.1 Inspection of Quality Certificate Documents 5.2 Inspection of Spherical Shell Plates and Test Plates 5.3 Inspection of Spherical Tank Pillars and Spare Parts 6 Field Assemblies 6.1 Inspection and Acceptance of Foundations 6.2 Installation of Sizing Blocks 6.3 Slicing Assembly Procedures of Spherical Tank 6.4 Girdle Assembly Procedures of Spherical Tank 6.5 Accessory Installation 6.6 Installation of Scaffolds and Other Temporary Facilities 6.7 Quality Inspection Method 7 Welding 7.1 General Rules 7.2 Welding Materials 7.3 Welding Procedures 7.4 Weld Inspection 7.5 Repair 8 Postwelding Whole Heat Treating 8.1 General Rules 8.2 Heat Treating Methods 8.3 Temperature Measurement 8.4 Post-heat-treating Quality Inspection 9 Product Welded Test plates 9.1 Preparation Requirements of Product Welded Test plates 9.2 Specimen Preparation and Test 10 Pressure Test and Gas Tight Test 10.1 General Rules 10.2 Hydraulic Test 10.3 Air Pressure Test 10.4 Air Tight Test 11 Handover Technical Documents Annex A Annex B Annex C Annex D Annex E
SH/T 3512-2002, SH 3512-2002, SHT 3512-2002, SH/T3512-2002, SH/T 3512, SH/T3512, SH3512-2002, SH 3512, SH3512, SHT3512-2002, SHT 3512, SHT3512
Introduction of SH/T 3512-2002
1.1 This standard specifies the construction procedures and methods of spherical tanks, as well as the requirements of field assembly welding procedure control, test/inspection/quality specifications and handover specifications.
1.2 This standard is applicable to the construction of orange-segment-model or mixed-model, pillar-supported, carbon steel/low alloy steel-welded spherical tanks (see Annex A) whose design pressure is larger than or equal to 0.1MPa but not larger than 4MPa, and whose nominal volume is larger than or equal to 50m3.
1.3 This standard is applicable to the following construction scopes of spherical tanks (see Article 1.1):
a）Spherical shell plate and its welding joint;
b）Pressure head, flat cover and fastener of spherical tank opening;
c）The following parts where the spherical shell pipes are connected with outside pipe:
1) The first girth joint groove head face of welded connection;
2) The first screwed joint head face of screwed connection;
3) The first flange sealing surface of flanged connection;
d） Non-pressure elements and their connection welds of the spherical tanks such as pillar, pull rod, backing plate and base plate.
1.4 This standard is not applicable to construction of the following spherical tanks:a）Spherical tanks suffering from nuclear radiation;
b）Non-fixed (such as vehicle or ship-borne) spherical tanks;
c）Spherical tanks with double-shell structures;
d）Spherical tanks formed by expansion.
Contents of SH/T 3512-2002
Foreword III
1 Scope
2 Normative References
3 General Provisions
4 Construction Preparations
4.1 Technical Preparation
4.2 Construction Field Preparation
4.3 Equipment Preparation
5 Acceptances of Spherical Shell Plates and Spare Parts
5.1 Inspection of Quality Certificate Documents
5.2 Inspection of Spherical Shell Plates and Test Plates
5.3 Inspection of Spherical Tank Pillars and Spare Parts
6 Field Assemblies
6.1 Inspection and Acceptance of Foundations
6.2 Installation of Sizing Blocks
6.3 Slicing Assembly Procedures of Spherical Tank
6.4 Girdle Assembly Procedures of Spherical Tank
6.5 Accessory Installation
6.6 Installation of Scaffolds and Other Temporary Facilities
6.7 Quality Inspection Method
7 Welding
7.1 General Rules
7.2 Welding Materials
7.3 Welding Procedures
7.4 Weld Inspection
7.5 Repair
8 Postwelding Whole Heat Treating
8.1 General Rules
8.2 Heat Treating Methods
8.3 Temperature Measurement
8.4 Post-heat-treating Quality Inspection
9 Product Welded Test plates
9.1 Preparation Requirements of Product Welded Test plates
9.2 Specimen Preparation and Test
10 Pressure Test and Gas Tight Test
10.1 General Rules
10.2 Hydraulic Test
10.3 Air Pressure Test
10.4 Air Tight Test
11 Handover Technical Documents
Annex A
Annex B
Annex C
Annex D
Annex E
