Detail of YD/T 1215-2006

Introduction of YD/T 1215-2006

Testing Methods of 900/1800MHz TDMA Digital Cellular Mobile Telecommunication Network General Packet Radio Service (GPRS) Equipment: Mobile Stations 1 Scope This standard specifies the testing methods of mobile stations (MS) of General Packet Radio Service (GPRS) in 900/1800MHz TDMA digital cellular mobile telecommunication network in terms of service, function, performance, electromagnetic compatibility and environmental adaptability. This standard is applicable to the test of mobile stations (MS) of General Packet Radio Service (GPRS) in 900/1800MHz TDMA digital cellular mobile telecommunication network; the contents other than those related to General Packet Radio Service (GPRS) are applicable to GSM mobile stations that do not support GPRS. 2 Normative References The following documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections) to, or revisions, of any of these publications do not apply to this standard. However parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. GB/T 18287 General Specification of Lithium-ion Cells and Batteries for Mobile Phone GB/T 18288 General Specification of Nickel-metal Hydride Battery for Cellular Phone GB/T 18289 General Specification of Nickel-cadmium Battery for Cellular Phone YD 1268 The Safety Specification and Test Method for Lithium Batteries and Charger YD/T 965 Safety Requirements and Test Method for User Equipment Technical Requirements and Testing Methods for Reliability of Mobile Telecommunication Handset Technical Requirements and Test Methods for Acoustics Performance of Digital Mobile Terminal YD 1032 Limits and Measurement Methods of Electromagnetic Compatibility for 900/1800 MHz TDMA Digital Cellular Telecommunications System—Part 1: Mobile Station and Ancillary Equipment 3GPP TS 02.04/ 3GPP TS 22.004 General on Supplementary Services 3GPP TS 51.010-1 Mobile Station (MS) Conformance Specification; Part 1: Conformance Specification 3 Abbreviations For the purposes of this standard, the following abbreviations apply. ARFCN Absolute Radio Frequency Channel Number AND Abbreviated Dialling Number AoC Advice of Charge B Bottom BCCH Broadcast Control Channel BER Bit Error Rate BFI Bad Frame Indication BLER Block Error Rate BSIC Base transceiver Station Identity Code CCCH Common Control Channel CS Coding Scheme Circuit Switched DCCH Dedicated Control Channel DTX Discontinuous transmission ETSI European Telecommunications Standards Institute FDN Fixed Dialing Number FER Frame Erasure Rate GPRS General Packet Radio Service GSM Global System Mobile HLR Home Location Register HT Hilly Terrain IMEI International Mobile Equipment Identity IMSI International Mobile Subscriber Identity IP Internet Protocol M Middle Frequency in the Supported Frequency Range of the MS under Test MAC Medium Access Control MMI Man Machine Interface MO Mobile Originated MS Mobile Station MT Mobile Terminated PDP Packet Data Protocol PDTCH Packet Data Traffic Channel PIN Personal Identification Number PLMN Public Land Mobile Network RA Rural Area RBER Residual Bit Error Ratio RF Radio Frequency RLC Radio Link Control RMS Root Mean Square value RR Radio Resource RX Receive SDCCH Stand-alone Dedicated Control Channel SGSN Serving GPRS Support Node SIM Subscriber Identity Module SM Short Message SMS Short Message Service T Top Frequency in the Supported Frequency Range of the MS under Test TCH Traffic Channel TCH/FS Traffic Channel/Full Rate Speech TDMA Time Division Multiple Access TE Test Equipment TU Terrestrial Urban TX Transmit Um Interface Interface between BBS and MS USF Uplink State Flag VBS Voice Broadcast Service VGCS Voice Group Call Service VLR Visitor Location Register WAP Wireless Application Protocol 4 Test Environment Normal test environment means a combination of the conditions specified in the following. Tests other than environmental adaptability tests shall be conducted in a normal test environment. The reference test environment for RF testing, audio testing, and protocol testing is shown in Figures 1, 2, and 3; the network test environment for service function test is shown in Figure 4, which contains a complete GSM/GPRS system. Temperature: 15°C to 35°C Relative humidity: 20% to 75% Power supply: Nominal value provided by manufacturer Instruments: mainly including wireless comprehensive tester, fading simulator, spectrum analyzer, audio analyzer and protocol analyzer. Wireless integrated tester is mainly used to simulate the base station equipment, communicate with the MS under test and measure some RF indexes. Fading simulator is mainly to simulate various multi-path fading modes on RF channels. Spectrum analyzer is mainly to test spectrum and conducted spurious emission. Acoustic analyzer is to test the acoustics performance of the NMS by connecting with the wireless comprehensive tester through the acoustic interface. Protocol analyzer is mainly to test protocols.

Contents of YD/T 1215-2006

Foreword i 1 Scope 2 Normative References 3 Abbreviations 4 Test Environment 5 Test of Services and Functions 6 Performance Test 7 Test of Layer 2 Signaling Functions 8 Test of Layer 3 Functions 9 Test of SIM/ME Interface 10 Test of Auto Call Barrings 11 Test of Bearer Services 12 Test of Supplement Services 13 Test of Speech Transcoding Functions 14 Test of Short Message Service (SMS) 15 Low Battery Voltage Detection 16 GPRS Paging, TBF Establishment/Release and DCCH Related Procedures 17 Test of Medium Access Control (MAC) Protocol 18 Radio Link Control (RLC) Test Cases 19 Test Case Requirements for GPRS Mobility Management 20 Session Management Procedures 21 Test of LLC and SNDCP 22 Dual Transfer Mode 23 Test of Electromagnetic Compatibility (EMC) 24 Test of Environmental Adaptability 25 Test of Battery and Charger 26 Test of Appearance, Packaging and Assembly