This standard specifies the rules for comparison of the measured values with the tolerance limits for surface texture parameters defined in GB/T 3505-2009, GB/T 18618, GB/T 18778.2-2003 and GB/T 18778.3-2006.
It also specifies the default rules for selection of cutoff wavelength, λc, for measuring roughness profile parameters according to GB/T 3505-2009 by using stylus instruments according to GB/T 6062.
2 Normative References
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections), or revisions, of any of these publications do not apply to this standard. However parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 131-2006 Geometrical Product Specifications (GPS) – Indication of Surface Texture in Technical Product Documentation (ISO 1302: 2002, IDT)
GB/T 1031-2009 Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Surface Roughness Parameters and Their Values
GB/T 18778.1-2002 Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Surfaces Having Stratified Functional Properties - Part 1: Filtering and General Measurement Conditions (eqv ISO 13565-1: 1996)
GB/T 18778.2-2003 Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Surface Having Stratified Functional Properties - Part 2: Height Characterization Using the Linear Material ratio Curve (ISO 13565-2: 1996, IDT)
GB/T 18778.3-2006 Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Surface Having Stratified Functional Properties - Part 3: Height Characterization Using the Material Probability Curve (ISO 13565-3: 1998, IDT)
Foreword i 1 Scope 2 Normative References 3 Terms and Definitions 4 Parameter Estimation 5 Rules for Comparison of the Measured Values with the Tolerance Limits 6 Parameter Evaluation 7 Rules and Procedures for Inspection Using Stylus Instruments Annex A (Informative) Simplified Procedure for Roughness Inspection Annex B (Informative) Relation to the GPS Matrix Model
1 Scope
This standard specifies the rules for comparison of the measured values with the tolerance limits for surface texture parameters defined in GB/T 3505-2009, GB/T 18618, GB/T 18778.2-2003 and GB/T 18778.3-2006.
It also specifies the default rules for selection of cutoff wavelength, λc, for measuring roughness profile parameters according to GB/T 3505-2009 by using stylus instruments according to GB/T 6062.
2 Normative References
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections), or revisions, of any of these publications do not apply to this standard. However parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 131-2006 Geometrical Product Specifications (GPS) – Indication of Surface Texture in Technical Product Documentation (ISO 1302: 2002, IDT)
GB/T 1031-2009 Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Surface Roughness Parameters and Their Values
GB/T 3505-2009 Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Terms Definitions and Surface Texture Parameters (ISO 4287: 1997, IDT)
GB/T 6062-2009 Geometrical Product Specifications (GPS) - Surface Texture: Profile Method – Nominal Characteristics of Contact (Stylus) Instruments (ISO 3274: 1996, IDT)
GB/T 18618-2002 Geometrical Product Specifications (GPS) - Surface Texture - Profile Method - Motif Parameters (eqv ISO 12085: 1996)
GB/T 18778.1-2002 Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Surfaces Having Stratified Functional Properties - Part 1: Filtering and General Measurement Conditions (eqv ISO 13565-1: 1996)
GB/T 18778.2-2003 Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Surface Having Stratified Functional Properties - Part 2: Height Characterization Using the Linear Material ratio Curve (ISO 13565-2: 1996, IDT)
GB/T 18778.3-2006 Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Surface Having Stratified Functional Properties - Part 3: Height Characterization Using the Material Probability Curve (ISO 13565-3: 1998, IDT)
Contents of GB/T 10610-2009
Foreword i
1 Scope
2 Normative References
3 Terms and Definitions
4 Parameter Estimation
5 Rules for Comparison of the Measured Values with the Tolerance Limits
6 Parameter Evaluation
7 Rules and Procedures for Inspection Using Stylus Instruments
Annex A (Informative) Simplified Procedure for Roughness Inspection
Annex B (Informative) Relation to the GPS Matrix Model
