GB/T 14048.12-2006 Low-voltage switchgear and controlgear - Part 4-3: Contactors and motor-starters-AC semiconductor controllers and contactors for non-motor loads (English Version)
1 Scope
This Standard applies to a.c. semiconductor non-motor load controllers and contactors intended for performing electrical operations by changing the state of a.c. electric circuits between the ON-state and the OFF-state. Typical applications are given in Table 2.
As controllers, they may be used to reduce the amplitude of the r.m.s. a.c. voltage on the load terminals from that of the applied voltage - either continuously or for a specified period of time. The half-wave period of the a.c. wave form remains unchanged from that of the applied voltage.
They may include a series mechanical switching device and are intended to be connected to circuits, the rated voltage of which does not exceed 1000 V a.c.
The controllers and contactors dealt with in this Standard are not normally intended to interrupt short-circuit currents. Therefore, suitable short-circuit protection (see 8.2.5) should form part of the installation but not necessarily of the controller itself.
In this context, this Standard gives requirements for semiconductor controllers and contactors associated with separate short-circuit protective devices.
This Standard does not apply to
- low-voltage a.c. semiconductor motor controllers and starters covered by GB 14048.6;
- electronic a.c. power controllers covered by IEC 60146;
- all-or-nothing solid-state relays.
Contactors and control-circuit devices used in semiconductor controllers and contactors should comply with the requirements of their relevant product standard. Where mechanical switching devices are used, they should meet the requirements of corresponding national standard and the additional requirements of this Standard.
The object of this Standard is to state
a) The characteristics of semiconductor controllers and contactors and associated equipment;
b) The conditions with which semiconductor controllers and contactors should comply with reference to
-their operation and behaviour;
-their dielectric properties;
- the degrees of protection provided by their enclosures, where applicable;
-their construction;
c) the tests intended for confirming that these conditions have been met, and the methods to be adopted for these tests;
d) the information to be given with the equipment or in the manufacturer’s literature.
1 Scope
2 Normative References
3 Terms and Definitions
4 Classification
5 Characteristics of a.c. Semiconductor Controllers and Contactors
6 Product Information
7 Normal Service, Mounting and Transport Conditions
8 Constructional and Performance Requirements
9 Tests
Annex A (Normative) Marking and Identification of Terminals
Annex B (Informative) Typical Service Conditions for Controllers and Contactors
Annex C Vacant
Annex D (Normative) Requirements for Radiated Emission Testing
Annex E (Informative) Method of Converting GB 4824-2004 Radiated Emission Limits to Transmitted Power Equivalents
Annex F (Informative) Operating Capability
Annex G (Informative) Examples of Control-circuit Configurations
Annex H (Informative) Items Subject to Agreement between Manufacturer and User
GB/T 14048.12-2006 Low-voltage switchgear and controlgear - Part 4-3: Contactors and motor-starters-AC semiconductor controllers and contactors for non-motor loads (English Version)
Standard No.
GB/T 14048.12-2006
Status
superseded
Language
English
File Format
PDF
Word Count
19000 words
Price(USD)
470.0
Implemented on
2007-4-1
Delivery
via email in 1 business day
Detail of GB/T 14048.12-2006
Standard No.
GB/T 14048.12-2006
English Name
Low-voltage switchgear and controlgear - Part 4-3: Contactors and motor-starters-AC semiconductor controllers and contactors for non-motor loads
1 Scope
This Standard applies to a.c. semiconductor non-motor load controllers and contactors intended for performing electrical operations by changing the state of a.c. electric circuits between the ON-state and the OFF-state. Typical applications are given in Table 2.
As controllers, they may be used to reduce the amplitude of the r.m.s. a.c. voltage on the load terminals from that of the applied voltage - either continuously or for a specified period of time. The half-wave period of the a.c. wave form remains unchanged from that of the applied voltage.
They may include a series mechanical switching device and are intended to be connected to circuits, the rated voltage of which does not exceed 1000 V a.c.
The controllers and contactors dealt with in this Standard are not normally intended to interrupt short-circuit currents. Therefore, suitable short-circuit protection (see 8.2.5) should form part of the installation but not necessarily of the controller itself.
In this context, this Standard gives requirements for semiconductor controllers and contactors associated with separate short-circuit protective devices.
This Standard does not apply to
- low-voltage a.c. semiconductor motor controllers and starters covered by GB 14048.6;
- electronic a.c. power controllers covered by IEC 60146;
- all-or-nothing solid-state relays.
Contactors and control-circuit devices used in semiconductor controllers and contactors should comply with the requirements of their relevant product standard. Where mechanical switching devices are used, they should meet the requirements of corresponding national standard and the additional requirements of this Standard.
The object of this Standard is to state
a) The characteristics of semiconductor controllers and contactors and associated equipment;
b) The conditions with which semiconductor controllers and contactors should comply with reference to
-their operation and behaviour;
-their dielectric properties;
- the degrees of protection provided by their enclosures, where applicable;
-their construction;
c) the tests intended for confirming that these conditions have been met, and the methods to be adopted for these tests;
d) the information to be given with the equipment or in the manufacturer’s literature.
Contents of GB/T 14048.12-2006
1 Scope
2 Normative References
3 Terms and Definitions
4 Classification
5 Characteristics of a.c. Semiconductor Controllers and Contactors
6 Product Information
7 Normal Service, Mounting and Transport Conditions
8 Constructional and Performance Requirements
9 Tests
Annex A (Normative) Marking and Identification of Terminals
Annex B (Informative) Typical Service Conditions for Controllers and Contactors
Annex C Vacant
Annex D (Normative) Requirements for Radiated Emission Testing
Annex E (Informative) Method of Converting GB 4824-2004 Radiated Emission Limits to Transmitted Power Equivalents
Annex F (Informative) Operating Capability
Annex G (Informative) Examples of Control-circuit Configurations
Annex H (Informative) Items Subject to Agreement between Manufacturer and User