General rules for flame retardant and fire resistant electric wires and cables or optical fiber cables
1 Scope
This standard specifies the burning behavior code, technical requirements, test methods and acceptance rules of flame retardant and fire resistant electric wires and cables or optical fiber cables, including the burning behavior of halogen-free, low smoke, low toxicity, flame retardance and fire resistance.
This standard is applicable to flame retardant and fire resistant electric wires and cables or optical fiber cables containing halogen, halogen-free or with low smoke or low toxicity.
2 Normative references
The following referenced documents are indispensable for the application of this standard. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendments) applies.
GB/T 4208-2017 Degrees of protection provided by enclosure (IP code)
GB/T 17650.1 Test on gases evolved during combustion of materials from cables or optical fiber cables — Part 1: Determination of the halogen acid gas content
GB/T 17650.2 Test on gases evolved during combustion of materials from cables or optical fiber cables — Part 2: Determination of acidity (by pH measurement) and conductivity
GB/T 17651.2 Measurement of smoke density of cables burning under defined conditions — Part 2: Test procedure and requirements
GB/T 18380.12 Tests on electric and optical fibre cables under fire conditions — Part 12: Test for vertical flame propagation for a single insulated wire or cable — Procedure for 1 kW pre-mixed flame
GB/T 18380.13 Tests on electric and optical fibre cables under fire conditions — Part 13: Test for vertical flame propagation for a single insulated wire or cable — Procedure for determination of flaming droplets/particles
GB/T 18380.22 Tests on electric and optical fibre cables under fire conditions — Part 22: Test for vertical flame propagation for a single small insulated wire or cable — Procedure for diffusion flame
GB/T 18380.33 Tests on electric and optical fibre cables under fire conditions — Part 33: Test for vertical flame spread of vertically-mounted bunched wires or cables — Category A
GB/T 18380.34 Tests on electric and optical fibre cables under fire conditions — Part 34: Test for vertical flame spread of vertically-mounted bunched wires or cables — Category B
GB/T 18380.35 Tests on electric and optical fibre cables under fire conditions — Part 35: Test for vertical flame spread of vertically-mounted bunched wires or cables — Category C
GB/T 18380.36 Tests on electric and optical fibre cables under fire conditions — Part 36: Test for vertical flame spread of vertically-mounted bunched wires or cables — Category D
GB/T 19216.21 Tests for electric cables under fire conditions — Circuit integrity — Part 21: Procedures and requirements — Cable of rated voltage up to and including 0.6/1.0 kV
GB/T 19216.23 Tests for electric cables under fire conditions — Circuit integrity — Part 23:Procedures and requirements — Electric data cables
GB/T 19216.25 Tests for electric cables under fire conditions — Circuit integrity — Part 25: Procedures and requirements — Optical fibre cables
IEC 60331-1 Tests for electric cables under fire conditions — Circuit integrity — Part 1: Test method for fire with shock at a temperature of at least 830°C for cables of rated voltage up to and including 0,6/1,0 kV and with an overall diameter exceeding 20 mm
IEC 60331-2 Tests for electric cables under fire conditions — Circuit integrity — Part 2: Test method for fire with shock at a temperature of at least 830°C for cables of rated voltage up to and including 0,6/1,0 kV and with an overall diameter not exceeding 20 mm
IEC 60684-2:2011 Flexible insulating sleeving — Part 2: Methods of test
IEC 60754-3 Test on gases evolved during combustion of materials from cables — Part 3: Measurement of low level of halogen content by ion chromatography
3 Terms and definitions
For the purpose of this document, the following terms and definitions apply.
3.1
flame retardance
burning behavior that after a sample is burned under the specified conditions, the flame spread on the sample only within a limited range after the fire source is removed, i.e., burning behavior of a sample to prevent or delay the occurrence or spread of flame
3.2
fire resistance
burning behavior that a sample can operate continuously under specified conditions when it is burned on a specified fire source and in specific period
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Product designation
5.1 Burning behavior codes and combinations
5.2 Composition of product model
5.3 Product representation method
6 Requirements of burning behavior
6.1 Flame retardance
6.2 Fire resistance
6.3 Halogen-free property
6.4 Low smoke
6.5 Low toxicity
7 Technical requirements
7.1 Flame retardant electric wire and cable or optical fiber cable series
7.2 Fire-resistant electric wires and cables or optical fiber cable series
8 Acceptance rules
Annex A (Normative) Water spray test method
Annex B (Normative) Water jet test method
Annex C (Normative) Toxicity index test method
Bibliography
General rules for flame retardant and fire resistant electric wires and cables or optical fiber cables
1 Scope
This standard specifies the burning behavior code, technical requirements, test methods and acceptance rules of flame retardant and fire resistant electric wires and cables or optical fiber cables, including the burning behavior of halogen-free, low smoke, low toxicity, flame retardance and fire resistance.
This standard is applicable to flame retardant and fire resistant electric wires and cables or optical fiber cables containing halogen, halogen-free or with low smoke or low toxicity.
2 Normative references
The following referenced documents are indispensable for the application of this standard. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendments) applies.
GB/T 4208-2017 Degrees of protection provided by enclosure (IP code)
GB/T 17650.1 Test on gases evolved during combustion of materials from cables or optical fiber cables — Part 1: Determination of the halogen acid gas content
GB/T 17650.2 Test on gases evolved during combustion of materials from cables or optical fiber cables — Part 2: Determination of acidity (by pH measurement) and conductivity
GB/T 17651.2 Measurement of smoke density of cables burning under defined conditions — Part 2: Test procedure and requirements
GB/T 18380.12 Tests on electric and optical fibre cables under fire conditions — Part 12: Test for vertical flame propagation for a single insulated wire or cable — Procedure for 1 kW pre-mixed flame
GB/T 18380.13 Tests on electric and optical fibre cables under fire conditions — Part 13: Test for vertical flame propagation for a single insulated wire or cable — Procedure for determination of flaming droplets/particles
GB/T 18380.22 Tests on electric and optical fibre cables under fire conditions — Part 22: Test for vertical flame propagation for a single small insulated wire or cable — Procedure for diffusion flame
GB/T 18380.33 Tests on electric and optical fibre cables under fire conditions — Part 33: Test for vertical flame spread of vertically-mounted bunched wires or cables — Category A
GB/T 18380.34 Tests on electric and optical fibre cables under fire conditions — Part 34: Test for vertical flame spread of vertically-mounted bunched wires or cables — Category B
GB/T 18380.35 Tests on electric and optical fibre cables under fire conditions — Part 35: Test for vertical flame spread of vertically-mounted bunched wires or cables — Category C
GB/T 18380.36 Tests on electric and optical fibre cables under fire conditions — Part 36: Test for vertical flame spread of vertically-mounted bunched wires or cables — Category D
GB/T 19216.21 Tests for electric cables under fire conditions — Circuit integrity — Part 21: Procedures and requirements — Cable of rated voltage up to and including 0.6/1.0 kV
GB/T 19216.23 Tests for electric cables under fire conditions — Circuit integrity — Part 23:Procedures and requirements — Electric data cables
GB/T 19216.25 Tests for electric cables under fire conditions — Circuit integrity — Part 25: Procedures and requirements — Optical fibre cables
IEC 60331-1 Tests for electric cables under fire conditions — Circuit integrity — Part 1: Test method for fire with shock at a temperature of at least 830°C for cables of rated voltage up to and including 0,6/1,0 kV and with an overall diameter exceeding 20 mm
IEC 60331-2 Tests for electric cables under fire conditions — Circuit integrity — Part 2: Test method for fire with shock at a temperature of at least 830°C for cables of rated voltage up to and including 0,6/1,0 kV and with an overall diameter not exceeding 20 mm
IEC 60684-2:2011 Flexible insulating sleeving — Part 2: Methods of test
IEC 60754-3 Test on gases evolved during combustion of materials from cables — Part 3: Measurement of low level of halogen content by ion chromatography
3 Terms and definitions
For the purpose of this document, the following terms and definitions apply.
3.1
flame retardance
burning behavior that after a sample is burned under the specified conditions, the flame spread on the sample only within a limited range after the fire source is removed, i.e., burning behavior of a sample to prevent or delay the occurrence or spread of flame
3.2
fire resistance
burning behavior that a sample can operate continuously under specified conditions when it is burned on a specified fire source and in specific period
Contents of GB/T 19666-2019
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Product designation
5.1 Burning behavior codes and combinations
5.2 Composition of product model
5.3 Product representation method
6 Requirements of burning behavior
6.1 Flame retardance
6.2 Fire resistance
6.3 Halogen-free property
6.4 Low smoke
6.5 Low toxicity
7 Technical requirements
7.1 Flame retardant electric wire and cable or optical fiber cable series
7.2 Fire-resistant electric wires and cables or optical fiber cable series
8 Acceptance rules
Annex A (Normative) Water spray test method
Annex B (Normative) Water jet test method
Annex C (Normative) Toxicity index test method
Bibliography