Rolling Bearing Parts—Skeleton Acrylonitrile-buta-diene Copolymers Seal —Specifications
1 Scope
This standard specifies the sizing material and skeleton of skeleton rubber seal ring (hereinafter referred to as seal ring) for deep groove ball bearings, and technical requirements, inspection and assessment methods, inspection rules and marks, packaging and transportation of finished products.
This standard is applicable to vulcanized acrylonitrile butadiene rubber (NBR) seal ring for sealed deep groove ball bearings specified in JB/T 7752-1995.
2 Normative References
The following normative documents contain provisions which, through reference in this standard, constitute provisions of this standard. For dated reference, subsequent amendments (excluding amending errors) to, or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest editions of these documents are applicable. For undated references, the latest edition of the normative document referred to applies.
GB/T 528-1998 Rubber,Vulcamized or Thermoplastic--Determination of Tensile Stress-strain Properties(eqv ISO 37: 1994)
GB/T 531-1999 Rubber-Determination of Indentation Hardness by Means of Pocket Hardness Meters (idt ISO 7619: 1986)
GB/T 1682-1994 Rubber, Vulcanized-Determination of Low-temperature Brittleness(Single Test Piece Method) (eqv ISO 812: 1991)
GB/T 1689-1998 Rubber Vulcanized—Determination of Abrasion Resistance (Akron machine) (neq BS 903:Part A9:1988)
GB/T 1690-1992 Rubber, Vulcanized - Determination of the Effect of Liquids (neq ISO 1817: 1985)
GB/T 2361-1992 Rust Preventing Oils and Greases - Test Method of Wet Heat (neq JIS K 2246:1989)
GB/T 2828-1987 In-batch Inspection Computation Sampling Procedure and Sampling Table (applicable to in-batch inspection)
GB/T 3512-2001 "Rubber Vulcanized or Thermoplastic-Accelerated Ageing and Heat Resistance Tests-Air-oven Method" (eqv ISO 188:1998)
GB/T 3522-1983 Cold-rolled Quality Carbon structural Steel Strips
GB/T 5721-1993 General Rules of Indentification, Packaging, Transportation and Storage for Rubber Sealing Products
GB/T 7759-1996 Rubber, Vulcanized or Thermoplastic-Determination of Compression Set at Ambient Elevated or Low Temperatures (eqv ISO 815: 1991)
GB/T 11211-1989 Rubber Vulcanized - Determination of Adhesion to Metal-Tension Method" (neq ISO 814: 1986)
JB/T 7752-1995 Sealed Deep Groove Ball Bearings - Specifications
3 Technical Requirements
3.1 Sizing material for seal ring
3.1.1 Sizing material for seal ring is vulcanized nitrile butadiene rubber. Refer to Table 1 for the indexes for physical properties of vulcanized nitrile butadiene rubber.
Table 1
Rolling Bearing Parts—Skeleton Acrylonitrile-buta-diene Copolymers Seal —Specifications
1 Scope
This standard specifies the sizing material and skeleton of skeleton rubber seal ring (hereinafter referred to as seal ring) for deep groove ball bearings, and technical requirements, inspection and assessment methods, inspection rules and marks, packaging and transportation of finished products.
This standard is applicable to vulcanized acrylonitrile butadiene rubber (NBR) seal ring for sealed deep groove ball bearings specified in JB/T 7752-1995.
2 Normative References
The following normative documents contain provisions which, through reference in this standard, constitute provisions of this standard. For dated reference, subsequent amendments (excluding amending errors) to, or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest editions of these documents are applicable. For undated references, the latest edition of the normative document referred to applies.
GB/T 528-1998 Rubber,Vulcamized or Thermoplastic--Determination of Tensile Stress-strain Properties(eqv ISO 37: 1994)
GB/T 531-1999 Rubber-Determination of Indentation Hardness by Means of Pocket Hardness Meters (idt ISO 7619: 1986)
GB/T 1682-1994 Rubber, Vulcanized-Determination of Low-temperature Brittleness(Single Test Piece Method) (eqv ISO 812: 1991)
GB/T 1689-1998 Rubber Vulcanized—Determination of Abrasion Resistance (Akron machine) (neq BS 903:Part A9:1988)
GB/T 1690-1992 Rubber, Vulcanized - Determination of the Effect of Liquids (neq ISO 1817: 1985)
GB/T 2361-1992 Rust Preventing Oils and Greases - Test Method of Wet Heat (neq JIS K 2246:1989)
GB/T 2828-1987 In-batch Inspection Computation Sampling Procedure and Sampling Table (applicable to in-batch inspection)
GB/T 3512-2001 "Rubber Vulcanized or Thermoplastic-Accelerated Ageing and Heat Resistance Tests-Air-oven Method" (eqv ISO 188:1998)
GB/T 3522-1983 Cold-rolled Quality Carbon structural Steel Strips
GB/T 5721-1993 General Rules of Indentification, Packaging, Transportation and Storage for Rubber Sealing Products
GB/T 7759-1996 Rubber, Vulcanized or Thermoplastic-Determination of Compression Set at Ambient Elevated or Low Temperatures (eqv ISO 815: 1991)
GB/T 11211-1989 Rubber Vulcanized - Determination of Adhesion to Metal-Tension Method" (neq ISO 814: 1986)
JB/T 7752-1995 Sealed Deep Groove Ball Bearings - Specifications
3 Technical Requirements
3.1 Sizing material for seal ring
3.1.1 Sizing material for seal ring is vulcanized nitrile butadiene rubber. Refer to Table 1 for the indexes for physical properties of vulcanized nitrile butadiene rubber.
Table 1
