Detail of T/CEEIA 334-2018

Introduction of T/CEEIA 334-2018

Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative. This standard is developed in accordance with the rules given in GB/T 1.1-2009 Directives for standardization—Part 1: Structure and drafting of standards and T/CEEIA 270-2017 Guidance for preparation of CEEIA standards. This standard was proposed by and is under the jurisdiction of Standardization Working Committee of China Electrical Equipment Industry Association. For the purpose of this standard, the Standardization Working Committee Secretariat of China Electrical Equipment Industry Association and Technical Committee of Low-voltage Apparatus are responsible for the explanation. Introduction Overcurrent protection circuit breaker in household and similar installation, as overload and short-circuit protection appliance in terminal circuit, is widely used in low-voltage apparatus. With the continuous development of modern science and technology, new technologies, new processes and new materials are constantly appearing, and the production process and various materials of circuit-breakers for overcurrent protection are constantly improved, which greatly improves the performance of circuit-breakers for overcurrent protection in household and similar installation. Green-design products are the ultimate embodiment of supply-side structural reform through green manufacturing, focusing on the greening of the whole life cycle of products. It is helpful to minimize energy and resource consumption and ecological environment impact and maximize regeneration rate by actively carrying out green-design and taking the impacts of raw material selection, production, sale, use, recovery and disposal on resources and environment in the product design and development stage according to the concept of the whole life cycle. This standard specifies the assessment principles and methods, organizational requirements, assessment indicators, assessment method for product life cycle and requirements of report format for green-design products of circuit-breakers for overcurrent protection in household and similar installation. The main contents of this standard are as follows: ——The applicable scope of standards and normative references are specified; ——The terms and definitions of product green-design are specified; ——The assessment principles, methods and basis of product green-design are specified; ——The assessment indicator requirements of product green-design are specified. Before the formulation of this standard, the assessment of green-design products of circuit-breakers for overcurrent protection in household and similar installation has been in a situation where there is no standard to follow, resulting in difference of manufacturers in green-design products and their environmental friendliness. The formulation of this standard enables all parties concerned to seriously study and discuss the green-design products of circuit-breakers for overcurrent protection, and improve the environmental protection awareness of all production enterprises. In addition, it provides basis for energy resources, ecological environment impact and regeneration rate of products. Main issues concerned in the standard are to: ——specify category and contents of hazardous substances restricted in products; ——specify the calculation method and indicator of recyclability rate of product; ——specify the operating life of products, which is higher than the current national standard by reference to the upper-middle level in the industry and the feedback from the participating units; ——specify the maximum power consumption index of products per pole, which is higher than the current national standard by reference to the upper-middle level in the industry. This standard is formulated in combination with the current energy-saving requirements, which helps to improve the whole industry's attention to the environmental friendliness of products, establish the green image of domestic brands and made-in-China products, and create good social benefits. Technical specification for green-design product assessment— Circuit-breakers for overcurrent protection for household and similar installation 1 Scope This standard specifies the assessment principles and methods, organizational requirements, assessment indicators, assessment method for product life cycle and requirements of report format for green-design products of circuit-breakers for overcurrent protection in household and similar installation. This standard is applicable to air circuit breakers with AC 50 Hz, 60 Hz or 50 Hz/60 Hz, rated voltage up to 440 V (phase-to-phase), DC rated voltage up to 500 V, rated current up to 125 A and rated short-circuit capability up to 25,000 A. It is also applicable to products containing electronic components, such as circuit breakers for equipment (CBE) complying with GB/T 17701. Note 1: Circuit-breakers for overcurrent protection in domestic and similar installation are called "products" in this standard. Note 2: This standard is also available to other products for household and similar installation. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 5480 Test methods for mineral wool and its products GB/T 10963.1-2005 Electrical accessories—Circuit-breakers for overcurrent protection for household and similar installation—Part 1: Circuit-breakers for a.c. operation GB/T 10963.3-2016 Circuit-breakers for overcurrent protection for household and similar installation—Part 3:Circuit-breakers for d.c. operation GB/T 16288 Marking of plastics products (ISO 11469, MOD) GB/T 17701 Circuit-breaker for equipment(IEC 60934, IDT) GB/T 17626 (All parts) Electromagnetic compatibility—Testing and measurement techniques (EC 61000-4, IDT) GB/T 18455 Package recycling marking GB/T 24040 Environmental management—Life cycle assessment—Principles and framework (ISO 14040，IDT） GB/T 24044 Environmental management—Life cycle assessment— Requirements and guidelines (ISO 14044, IDT) GB/T 26125 Electrical and electronic products—Determination of six regulated substances (lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls, polybrominated diphenyl ethers)(IEC 62321, IDT) GB/T 26572 Requirements of concentration limits for certain restricted substances in electrical and electronic products GB/T 29493.2-2013 Determination of harmful substances in textile dyeing and finishing auxiliaries - Part 2: Determination of perfluorooctane sulfonates and perfluorooctanoicacid—HPLC-MS/MS method GB/T 29609-2013 Rubber—Determination of phenol and biphenyl-A GB/T 29786-2013 Determination of phthalates in electrical and electronic equipments—Gas chromatography-mass spectrometry GB/T 33344 Determination of short-chain chlorinated paraffin in electronic and electrical products—Gas chromatography-mass spectrometry SJ/T 11364-2014 Marking for the restriction of the use of hazardous substances in electrical and electronic product 3 Terms and definitions For the purposes of this document, the terms and definitions given in GB/T 10963 and GB/T 24040 and the following apply. 3.1 green-design behaviour of considering the impacts of raw material acquisition, manufacturing, packaging and transportation, use and maintenance, recycling and other links on resources and environment in the product design and development stage based on the concept of the whole life cycle, in order to minimize resource consumption, minimize or eliminate raw materials containing harmful substances as much as possible, and reduce the generation and emission of pollutants, thus realizing environmental protection Note 1: Green-design is also called ecological design, environmental design or environmental conscious design. Note: It is revised from GB/T 32161-2015, 3.2. 3.2 green-design products products that meet the green-design concept and assessment requirements Note: Green-design products are also called ecological design products, environmental design products or environmental conscious design products. [GB/T 32161-2015, 3.3] 3.3 environment external condition of an organization's operational activities, including air, water, land, natural resources, plants, animals and people, and their interrelationships Note 1: External conditions may extend from the organization to local, regional and global systems. Note 2: External conditions can be described by biodiversity, ecosystem, climate or other characteristics. [GB/T 24001-2016, 3.1] 3.4 life cycle thinking; LCT thinking about all relevant environmental aspects in the whole life cycle of the product [GB/T 23686-2009, 3.11] 3.5 recyclability rate percentage of the total mass of the electronic and electrical products expected to be reused and recycled (excluding the energy recovery part) and the total mass of the electronic and electrical products [GB/T 29769-2013, 3.18] 4 Assessment principles, methods and basis 4.1 Assessment principles Product assessment shall follow the following principles: a) Life cycle thinking: use life cycle thinking to systematically consider the important environmental aspects that have great influence on the environment in each stage of the whole life cycle of products; b) Combination of qualitative and quantitative assessments: qualitative or quantitative assessment criteria shall be put forward when implementing green-design product assessment. If feasible, it is encouraged to select quantitative assessment requirements as far as possible, so as to reflect the environmental performance of products more accurately. 4.2 Assessment method Product assessment methods are as follows: a) indicator assessment, includes, but is not limited to: 1) product environmental protection requirements specified in laws and regulations; 2) other advanced environmental protection requirements for products. Note: The sources of environmental protection requirements include enterprise environmental protection policies, national/industrial technical standards, customer requirements, environmental protection marks or green procurement technical specifications, etc. b) Life cycle assessment Product life cycle assessment is carried out according to GB/T 24040, GB/T 24044 and specific product category rules and standards. 4.3 Assessment basis Products shall be assessed as green-design products if they a) meet the basic requirements for the organization (see Clause 5) and the assessment indicator requirements for products (see Clause 6), and relevant compliance documents are provided; b) are subjected to product life cycle assessment (see Annex A for the assessment method for product life cycle) and green-design assessment report is provided (see Annex B for report format). 5 Basic requirements for product manufacturers Product manufacturers shall introduce green-design process into management system: ——Incorporating the goal of green-design and reducing the overall environmental impact into enterprise policies and strategies; ——Being consistent with the management system procedures of the enterprise, regularly review the green-design process to promote continuous improvement; ——The review content includes enterprise policies and strategies, necessity to improve the green-design process and possibility to improve the environmental performance of products. 6 Requirements of assessment indicator The assessment product shall be a green-design product, which consists of first-class indicator and second-class indicator. The first-class indicator includes resource, energy, environment and product attribute. Second-class indicators are specific assessment items in four types of attribute indicators, including indicator names, criteria, basis, etc. See Table 1 for the requirements of assessment indicator.

Contents of T/CEEIA 334-2018

Foreword i Introduction ii 1 Scope 2 Normative references 3 Terms and definitions 4 Assessment principles, methods and basis 5 Basic requirements for product manufacturers 6 Requirements of assessment indicator Annex A (Informative) Assessment method for product life cycle Annex B (Informative) Format of green-design assessment report of products Annex C (Normative) Calculation method of product recyclability rate Bibliography