Detail of 16G101-2

Introduction of 16G101-2

1. This drawing collection is based on the MOHURD document No. [2016] 89 Notification of Distributing the Working Plan of Compiling the National Standard Design for Buildings in 2016. 2. This drawing collection is the national building standard design drawing collection for construction drawings of cast-in-situ concrete slab-stairs using ichnographic representing method (IRM). Ichnographic representing, in general, is to show dimensions and reinforcement details of structural members directly in the structural plan layout according to rules of IRM. A completed set of structural construction drawings shall include both IRM drawings and standard detailing drawings. 3. Main design references in this drawing collection are: Seismic Ground Motion Parameters Zonation Map of China (GB 18306-2015); Code for Design of Concrete Structures (2015 version) (GB 50010-2010); Code for Seismic Design of Buildings (GB 50011-2010) and its partial revision in 2016; Technical Specification for Concrete Structures of Tall Building (JGJ 3-2010) Standard for Structural Drawings (GB/T 50105-2010) If the reference standards are revised or new standards are implemented and the contents or products in this drawing collection are conflicted with them, such contents or products shown in this drawing collection shall be looked on as invalid. Engineers who use this drawing collection shall check relevant contents in this drawing collection with updated standards. 4. There are two parts in this drawing collection: drawing rules of cast-in-situ concrete slab-stairs and standard detailing drawings. 5. This drawing collection is applicable to cast-in-situ concrete slab-stairs in seismic design with seismic precautionary intensity 6~9. 6. The rules specified in this drawing collection can be used for designers to generate ichnographic construction drawings of stairs or can be used as reference for contractors and inspectors to understand and use ichnographic construction drawings correctly. 7. Details and other items which are not included in this drawing collection should be worked out by designers. 8. If modifications of the standard detailing drawings in this drawing collection are required for certain projects, designers should provide specific modified contents. 9. All dimensions are in millimeters (mm), and structural levels are in meters (m). 10. Type codes in this drawing collection: Stair slab—AT~GT, ATa, ATb, ATc, CTa and CTb; landing slab—PTB; stair beam—TL; stair column—TZ 11. To uniform the expression, the direction of travel upwards of all the stairs in this drawing collection is anticlockwise. However, drawing rules and detailing are applicable to all stairs no matter the direction of travel upwards is clockwise or anticlockwise. 12. Are there any questions and comments when using this drawing collection, please visit webpage http://www.chinabuilding.com.cn, and contact us via G101. 1 General Provisions 1.1.1 Setting the rules of IRM is to standardize the use of IRM in structural construction drawings of buildings, to uniform the format of construction drawings carried out by IRM, and to ensure the quality of design and construction. 1.1.2 The rules in this drawing collection are applicable to cast-in-situ concrete slab-stairs. 1.1.3 Apart from the rules of the IRM in this drawing collection, other updated national standards shall also be complied with. 1.1.4 Construction drawings carried out in accordance with IRM usually consist of two main parts, ichnographic construction drawings of stairs and standard detailing drawings. 1.1.5 IRM of stair slabs includes ichnographic annotation, sectional annotation and tabulated annotation. IRM of landing slabs, stair beams and stair columns should comply with the drawing collection for national building standard design 16G101-1 Drawing Rules and Standard Detailing Drawings of Ichnographic Representing Method for Construction Drawings of R.C. Structures (Cast-in-situ R.C. Frames, Shear Walls, Beams and Slabs). 1.1.6 For ichnographic construction drawings, the structural floor level, story height and corresponding floor number of floors below and above ground level shall be shown in tables or by other methods. Structural floor level shall be coordinate with structural story height in the same project in order to set the vertical position of foundations, columns, walls, beams, slabs, etc.- properly. For the convenience of construction, the structural floor level, structural story height shall be shown in ichnographic construction drawing of all kinds of structural members such as columns, walls and beams. Note: Structural floor level is the floor level shown in architectural drawings excluding the thickness of floor finishing and cushion layers. The floor number in structural drawings shall be consistent with that in architectural drawings. 1.1.7 When ichnographic construction drawings are prepared, every structural member should be numbered, and the numbering of each member includes the type code and serial number. The type code is to indicate relevant standard detailing drawings. Standard detailing drawings are noted with the type code of members to show the complementary relationship between the detailing drawings and corresponding types of members in ichnographic construction drawings. A completed set of structural design drawings shall include both ichnographic construction drawings and standard detailing drawings. 1.1.8 In order to carry out construction properly according to ichnographic construction drawings, the information, which is closely relevant to ichnographic construction drawings, has to be specified in specific construction drawings as below: 1. The reference number of the adopted ichnographic standard drawing collection (e.g. 16G101-2 for this drawing collection) shall be specified in order to prevent any misuse of the drawing collection once updated.

Contents of 16G101-2

Hooks and mechanical anchorage types of longitudinal bars Stirrup detailing in the lap zone of longitudinal main bars Splice of longitudinal bars Lap length ll of longitudinal tension bars Lap length llE of longitudinal tension bars in seismic design Ichnographic annotation method and application of AT stairs Reinforcement detailing of AT stair slabs Ichnographic annotation method and application of BT stairs Reinforcement detailing of BT stair slabs Ichnographic annotation method and application of CT stairs Reinforcement detailing of CT stair slabs Ichnographic annotation method and application of DT stairs Reinforcement detailing of DT stair slabs Ichnographic annotation method and application of ET stairs Reinforcement detailing of ET stair slabs Ichnographic annotation method and application of FT stairs Reinforcement detailing of FT stair slabs (Section 1-1) Reinforcement detailing of FT stair slabs (Section 2-2) Ichnographic annotation method and application of GT stairs Reinforcement detailing of GT stair slabs (Section 1-1) Reinforcement detailing of GT stair slabs (Section 2-2) Reinforcement detailing of the landing slab of FT and GT stairs (Section 3-3 and 4-4) Ichnographic annotation method and application of ATa and ATb stairs Detailing drawings of slide bearings of ATa and CTa stairs Reinforcement detailing of ATa stair slabs Detailing drawings of slide bearings of ATb and CTb stairs Reinforcement detailing of ATb stair slabs Ichnographic annotation method and application of ATc stairs Reinforcement detailing of ATc stair slabs Ichnographic annotation method and application of CTa and CTb stairs Reinforcement detailing of CTa stair slabs Reinforcement detailing of CTb stair slabs Detailing of increasing and decreasing rise at different risers Connection detailing between the first flight of stairs and foundations Sectional annotation example of construction drawings of AT~DT stairs (plan) Sectional annotation example of construction drawings of AT~DT stairs (section) Sectional annotation example of construction drawings of ATa stairs (plan) Sectional annotation example of construction drawings of ATa stairs (section) Sectional annotation example of construction drawings of ATb stairs (plan) Sectional annotation example of construction drawings of ATb stairs (section) Sectional annotation example I of construction drawings of ATc stairs (plan) Sectional annotation example I of construction drawings of ATc stairs (section) Sectional annotation example Ⅱ of construction drawings of ATc stairs (plan) Sectional annotation example II of construction drawings of ATc stairs (section) Sectional annotation example of construction drawings of CTa stairs (plan) Sectional annotation example of construction drawings of CTa stairs (section) Sectional annotation example of construction drawings of CTb stairs (plan) Sectional annotation example of construction drawings of CTb stairs (section)