This standard specifies the limits and measurement methods for emissions of exhaust pollutants from two-wheeled or three-wheeled mopeds on running mode, requirements for emission of pollutants from crankcase and durability requirements of pollution control device.
This standard specifies the requirements of type approval, production conformity inspection and judgment method for two-wheeled and three-wheeled mopeds at Stage III.
This standard is applicable to two-wheeled or three-wheeled mopeds which are equipped with spark-ignition engine and with the complete vehicle kerb mass not greater than 400kg, the engine displacement not greater than 50mL and the maximum design speed not greater than 50km/h.
2 Normative References
The following standards contain provisions which, through reference in this standard, constitute provisions of this standard. For dated references, subsequent amendments to (excluding corrigendum), or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of these standards applies.
GB/T 5359.5-1996 Term for Motorcycles and Mopeds - Mass of Vehicle with Two Wheels
GB/T 5359.6-1996 Term for Motorcycles and Mopeds - Mass of Vehicle with Three Wheels
GB/T 15089-2001 Classification of Power-driven Vehicles and Trailers
3 Terms and Definitions
Foreword i 1 Application Scope 2 Normative References 3 Terms and Definitions 4 Application and Approval of Type Approval 5 Technical Requirements 6 Type Approval Test and Emission Limits 7 Production Conformity Inspection 8 Type Approval Extension 9 Implementation of Standard Appendix A (Normative) Type Approval Application Information Appendix B (Normative) Format of Type Approval Certificate [Maximum Dimensions: A4 (210mm×297mm)] Appendix C (Normative) Measurement of Average Emissions of Exhaust Pollutants after Cold Start at Room Temperature (Type I Test) Appendix D (Normative) Durability Test of Pollution Control Device (Type V Test) Appendix E (Normative) Production Conformity Inspection Specification Appendix F (Normative) Technical Requirements of Reference Fuel
1 Application Scope
This standard specifies the limits and measurement methods for emissions of exhaust pollutants from two-wheeled or three-wheeled mopeds on running mode, requirements for emission of pollutants from crankcase and durability requirements of pollution control device.
This standard specifies the requirements of type approval, production conformity inspection and judgment method for two-wheeled and three-wheeled mopeds at Stage III.
This standard is applicable to two-wheeled or three-wheeled mopeds which are equipped with spark-ignition engine and with the complete vehicle kerb mass not greater than 400kg, the engine displacement not greater than 50mL and the maximum design speed not greater than 50km/h.
2 Normative References
The following standards contain provisions which, through reference in this standard, constitute provisions of this standard. For dated references, subsequent amendments to (excluding corrigendum), or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of these standards applies.
GB/T 5359.5-1996 Term for Motorcycles and Mopeds - Mass of Vehicle with Two Wheels
GB/T 5359.6-1996 Term for Motorcycles and Mopeds - Mass of Vehicle with Three Wheels
GB/T 15089-2001 Classification of Power-driven Vehicles and Trailers
3 Terms and Definitions
Contents of GB 18176-2007
Foreword i
1 Application Scope
2 Normative References
3 Terms and Definitions
4 Application and Approval of Type Approval
5 Technical Requirements
6 Type Approval Test and Emission Limits
7 Production Conformity Inspection
8 Type Approval Extension
9 Implementation of Standard
Appendix A (Normative) Type Approval Application Information
Appendix B (Normative) Format of Type Approval Certificate [Maximum Dimensions: A4 (210mm×297mm)]
Appendix C (Normative) Measurement of Average Emissions of Exhaust Pollutants after Cold Start at Room Temperature (Type I Test)
Appendix D (Normative) Durability Test of Pollution Control Device (Type V Test)
Appendix E (Normative) Production Conformity Inspection Specification
Appendix F (Normative) Technical Requirements of Reference Fuel
