Detail of NB/T 33008.1-2018

Introduction of NB/T 33008.1-2018

NB/T 33008.1-2018 Inspection and test specifications for electric vehicle charging equipment - Part 1: Off-board charger 1 Scope This part specifies the inspection rules and test methods for off-board chargers of electric vehicles (hereinafter referred to as chargers). This part is applicable to type test, end-of-manufacturing inspection and arrival acceptance of chargers. This part is applicable to chargers specified in NB/T 33001-2018. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendments) applies. GB/T 2421.1-2008 Environmental testing for electric and electronic products - General and guidance GB/T 2423.1-2008 Environmental testing for electric and electronic products - Part 2: Test methods - Tests A: Cold GB/T 2423.2-2008 Environmental testing for electric and electronic products - Part 2: Test methods - Test B: Dry heat GB/T 2423.4-2008 Environmental testing for electric and electronic products - Part 2: Test method - Test Db: Damp heat, cyclic (12h+12h cycle) GB/T 2423.17-2008 Environmental testing for electric and electronic products - Part 2: Test methods - Test Ka: Salt mist GB/T 2423.55-2006 Environmental testing for electric and electronic products - Part 2: Test methods - Test Eh: Hammer tests GB 4208 Degrees of protection provided by enclosure (IP code) GB 4824-2013 Industrial, scientific and medical (ISM) radio-frequency equipment - Disturbance characteristics - Limits and methods of measurement GB/T 7251.1-2013 Low-voltage switchgear and controlgear assemblies - Part 1: General rules GB 17625.1 Electromagnetic compatibility - Limits - Limits for harmonic current emissions (equipment input current ≤ 16A per phase) GB/T 17625.2 Electromagnetic compatibility (EMC)- Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤16A per phase and not subject to conditional connection GB/T 17625.7 Electromagnetic compatibility - Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems for equipment with rated current ≤ 75A and subject to conditional connection GB/T 17625.8 Electromagnetic compatibility - Limits - Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current > 16A and ≤ 75A per phase GB/T 17626.2 Electromagnetic compatibility - Testing and measurement techniques - Electrostatic discharge immunity test GB/T 17626.3 Electromagnetic compatibility - Testing and measurement techniques - Radiated radio-frequency electromagnetic field immunity test GB/T 17626.4 Electromagnetic compatibility - Testing and measurement techniques - Electrical fast transient/burst immunity test GB/T 17626.5 Electromagnetic compatibility - Testing and measurement techniques - Surge immunity test GB/T 17626.6 Electromagnetic compatibility - Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields GB/T 17626.8 Electromagnetic compatibility - Testing and measurement techniques - Power frequency magnetic field immunity test GB/T 17626.11 Electromagnetic compatibility - Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests GB/T 17626.34 Electromagnetic compatibility - Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests for equipment with mains current more than 16A per phase GB/T 18487.1-2015 Electric vehicle conductive charging system - Part 1: General requirements GB/T 18487.2-2017 Electric vehicle conductive charging system - Part 2: EMC requirements for off-board electric vehicle supply equipment GB/T 20234.1-2015 Connection set for conductive charging of electric vehicles - Part 1: General requirements GB/T 20234.3-2015 Connection set for conductive charging of electric vehicles - Part 3: DC charging coupler GB/T 27930-2015 Communication protocols between off-board conductive charger and battery management system for electric vehicle GB/T 29317 Terminology of electric vehicle charging/battery swap infrastructure GB/T 29318 Electric energy metering for electric vehicle off-board charger GB/T 34657.1-2017 Interoperability test specifications of electric vehicle conductive charging - Part 1: Supply equipment GB/T 34658-2017 Conformance test for communication protocols between off-board conductive charger and battery management system for electric vehicle NB/T 33001-2018 Specification for electric vehicle off-board conductive charger IEC 61851-23 Electric vehicle conductive charging system - Part 23: DC electric vehicle charging station 3 Terms and definitions For the purpose of this document, the terms and definitions defined in GB/T 18487.1-2015, GB/T 18487.2-2017, GB/T 29317 and NB/T 33001-2018 apply. 4 Inspection rules 4.1 Inspection classification The inspection of products can be classified intro type inspection, end-of-manufacturing inspection and arrival inspection. 4.1.1 Type test In the following cases, the products must be subject to type test: a) products newly put into production (including products produced at transferred factories) shall be subjected to type test before production appraisal; b) in case of change in and impact on product performance due to the changes in design, process or major components, type tests shall be conducted before the products are into production; c) for products that have been discontinued for more than two years, type tests shall be conducted before they are put into production again. 4.1.2 End-of-manufacturing inspection Each product shall be subject to end-of-manufacturing inspection. Only after being confirmed by the quality inspection department of the manufacturer, can it leave the factory with a certificate proving that the product is qualified. 4.1.3 Arrival acceptance The receiving unit should inspect the received products before use, and the products can only be put into use after passing the acceptance. The specific acceptance sampling plan shall be decided by each receiving unit voluntarily. 4.2 Test items The test items of chargers are shown in Table 1. Table 1 Test items of chargers

Contents of NB/T 33008.1-2018

Foreword i 1 Scope 2 Normative references 3 Terms and definitions 4 Inspection rules 5 Test methods Annex A (Informative) Battery simulation test device