Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
This standard is developed in accordance with the rules given in GB/T 1.1-2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. The issuing body of this document shall not be held responsible for identifying any or all such patent rights.
This standard was proposed by the State Forestry Administration of the People's Republic of China
This standard is under the jurisdiction of the National Technical Committee on Wood-based Panels of Standardization Administration of China (SAC/TC 198).
Surface decorated plywood and blockboard with paper impregnated thermosetting resins
1 Scope
This standard specifies terms and definitions, classification, requirements, inspection methods, inspection rules as well as identification, packaging, transportation and storage of surface decorated plywood and blockboard with paper impregnated thermosetting resins.
This standard is applicable to surface decorated plywood and blockboard with paper impregnated thermosetting resins.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 2828.1-2012 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
GB/T 9846-2015 Plywood for general use
GB/T 17657-2013 Test methods of evaluating the properties of wood-based panels and surface decorated wood-based panels
GB/T 18259-2009 Terms of wood-based panel and its surface decoration
GB 18580 Indoor decorating and refurbishing materials - Limit of formaldehyde emission of wood-based panels and finishing products
GB/T 19367-2009 Wood-based panels - Determination of dimensions of panels
3 Terms and definitions
For the purposes of this document, the terms and definitions given in GB/T 18259-2009 and the following apply. For the convenience of use, some terms and definitions in GB/T 18259-2009 are listed below.
3.1
surface decorated plywood and blockboard with paper impregnated thermosetting resins
decorative panel after hot pressing, installing on plywood or blockboard substrate by impregnated paper with thermosetting amino resin
3.2
color unmatching
difference between a certain pattern color and the given standard sample pattern color
[GB/T 18259-2009, Definition 2.2.4.64]
3.3
misalignment between panel and impregnated paper
paper shortage in product panel caused by misalignment between impregnated paper and substrate, including white edge and crack of decorative paper printing
3.4
tearing of impregnated paper
fracture trace on the surface of product caused by partial rupture of impregnated paper
3.5
bare substrate spots due to defective surface covering
defect exposed to the substrate due to defective impregnated paper
3.6
substrate revealment
phenomenon of the color or defect of the substrate on the surface due to the color of impregnated paper or insufficient covering
[GB/T 18259-2009, Definition 2.2.4.68]
3.7
dents
jagged defects at the edge of decorative surface caused during edging
Note: it is revised from Definition 2.2.4.69, GB/T 18259-2009.
3.8
blisters
elevation induced by gas present in product surface
Note: it is revised from Definition 2.1.73, GB/T 18259-2009.
3.9
bulge
elevation induced by solid present in product surface
Note: it is revised from Definition 2.2.4.70, GB/T 18259-2009.
3.10
delaminating
segregation of substrate, of impregnated paper or between impregnated paper and substrate
[GB/T 18259-2009, Definition 2.2.4.71]
3.11
light fastness
resistance of product surface color to radiation of daylight or artificial light
[GB/T 18259-2009, Definition 2.2.4.72]
3.12
surface waviness
waved defect formed on the surface of product
4 Classification
4.1 Classification by substrate:
——the surface decorated plywood with paper impregnated thermosetting resins;
——the surface decorated blockboard with paper impregnated thermosetting resins.
4.2 Classification by decorated surface:
——the surface decorated plywood and blockboard with paper impregnated thermosetting resins with single decorated surface;
——the surface decorated plywood and blockboard with paper impregnated thermosetting resins with double decorated surface;
5 Requirements
5.1 Grading
According to the appearance quality, surface decorated plywood and blockboard with paper impregnated thermosetting resins are divided into superior products, first-grade products and qualified products.
Foreword i 1 Scope 2 Normative references 3 Terms and definitions 4 Classification 5 Requirements 6 Inspection methods 7 Inspection rules 8 Identification, packaging, transportation and storage
Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
This standard is developed in accordance with the rules given in GB/T 1.1-2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. The issuing body of this document shall not be held responsible for identifying any or all such patent rights.
This standard was proposed by the State Forestry Administration of the People's Republic of China
This standard is under the jurisdiction of the National Technical Committee on Wood-based Panels of Standardization Administration of China (SAC/TC 198).
Surface decorated plywood and blockboard with paper impregnated thermosetting resins
1 Scope
This standard specifies terms and definitions, classification, requirements, inspection methods, inspection rules as well as identification, packaging, transportation and storage of surface decorated plywood and blockboard with paper impregnated thermosetting resins.
This standard is applicable to surface decorated plywood and blockboard with paper impregnated thermosetting resins.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 2828.1-2012 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
GB/T 9846-2015 Plywood for general use
GB/T 17657-2013 Test methods of evaluating the properties of wood-based panels and surface decorated wood-based panels
GB/T 18259-2009 Terms of wood-based panel and its surface decoration
GB 18580 Indoor decorating and refurbishing materials - Limit of formaldehyde emission of wood-based panels and finishing products
GB/T 19367-2009 Wood-based panels - Determination of dimensions of panels
3 Terms and definitions
For the purposes of this document, the terms and definitions given in GB/T 18259-2009 and the following apply. For the convenience of use, some terms and definitions in GB/T 18259-2009 are listed below.
3.1
surface decorated plywood and blockboard with paper impregnated thermosetting resins
decorative panel after hot pressing, installing on plywood or blockboard substrate by impregnated paper with thermosetting amino resin
3.2
color unmatching
difference between a certain pattern color and the given standard sample pattern color
[GB/T 18259-2009, Definition 2.2.4.64]
3.3
misalignment between panel and impregnated paper
paper shortage in product panel caused by misalignment between impregnated paper and substrate, including white edge and crack of decorative paper printing
3.4
tearing of impregnated paper
fracture trace on the surface of product caused by partial rupture of impregnated paper
3.5
bare substrate spots due to defective surface covering
defect exposed to the substrate due to defective impregnated paper
3.6
substrate revealment
phenomenon of the color or defect of the substrate on the surface due to the color of impregnated paper or insufficient covering
[GB/T 18259-2009, Definition 2.2.4.68]
3.7
dents
jagged defects at the edge of decorative surface caused during edging
Note: it is revised from Definition 2.2.4.69, GB/T 18259-2009.
3.8
blisters
elevation induced by gas present in product surface
Note: it is revised from Definition 2.1.73, GB/T 18259-2009.
3.9
bulge
elevation induced by solid present in product surface
Note: it is revised from Definition 2.2.4.70, GB/T 18259-2009.
3.10
delaminating
segregation of substrate, of impregnated paper or between impregnated paper and substrate
[GB/T 18259-2009, Definition 2.2.4.71]
3.11
light fastness
resistance of product surface color to radiation of daylight or artificial light
[GB/T 18259-2009, Definition 2.2.4.72]
3.12
surface waviness
waved defect formed on the surface of product
4 Classification
4.1 Classification by substrate:
——the surface decorated plywood with paper impregnated thermosetting resins;
——the surface decorated blockboard with paper impregnated thermosetting resins.
4.2 Classification by decorated surface:
——the surface decorated plywood and blockboard with paper impregnated thermosetting resins with single decorated surface;
——the surface decorated plywood and blockboard with paper impregnated thermosetting resins with double decorated surface;
5 Requirements
5.1 Grading
According to the appearance quality, surface decorated plywood and blockboard with paper impregnated thermosetting resins are divided into superior products, first-grade products and qualified products.
Contents of GB/T 34722-2017
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Requirements
6 Inspection methods
7 Inspection rules
8 Identification, packaging, transportation and storage
